MSI MS-6189 Manual de usuario
CHAPTER 1CHAPTER 1
CHAPTER 1CHAPTER 1
CHAPTER 1 INTRODUCTIONINTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
1-1
TheMS-6189MICROATXSI1mainboardisahigh-performancecomputer
mainboard based on SiS®630E chipset. The MS-6189 is designed for the
Intel®CeleronTM/Pentium III(FC-PGA) processor for inexpensive business/
personal desktop markets.
The SiS630E provides a high performance/low cost Desktop solution for the
socket 370 series CPUs based system by integrating a high performance
North Bridge, advanced hardware 2D/3D GUI engine and Super-South
bridge. SiS630E also adopts Share System Memory Architecture which can
flexibly utilize the frame buffer size up to 64MB. The “Super-South Bridge”
in SiS630E integrates all peripheral controllers /accelerators /interfaces.
SiS630E offers AC’97 compliant interface that comprises digital audio engine
with 3D-hardware accelerator, on-chip sample rate converter, and profes-
sional wavetable along with separate modem DMA controller. SiS630E also
provides interface to Low Pin Count (LPC) operating at 33 MHz clock which
is the same as PCI clock on the host, and dual USB host controller with four
USB ports that deliver better connectivity and 2 x 12Mb bandwidth.
The built-in fast PCI IDE controller supports the ATA PIO/DMA, and the
Ultra DMA33/66 function that supports the data transfer rate up to 66 MB/s.
It provides the separate data path for two IDE channels that can eminently
improve the performance under the multi-tasking environment.
Chapter 1
INTRODUCTION
CHAPTER 1CHAPTER 1
CHAPTER 1CHAPTER 1
CHAPTER 1 INTRODUCTIONINTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
1-2
1.1 Mainboard Features
CPU
!Support Socket370 for Intel®CeleronTM/Pentium III(FC-PGA) processor
and Cyrix III Processor.
!Support300MHz,333MHz,366MHz,400MHz,433MHz,466MHz,500MHz,
533MHz,550MHz,667MHz,700MHz,750Mhz,800MHz,orhigher proces-
sor
Chipset
!SiS®630Echipset.
-AGP4xGraphics chip
- 3D Positional Audio
-UltraATA66IDE
- Integrated 10/100Mb Fast Ethernet
!Winbond 83697HF chipset
- Enhanced Hardware Monitor
- Low pin count interface for SIO
FrontSideBus(FSB)
!66/100/133MHzclocks are supported.
MainMemory
!Support two 168-pin DIMM sockets.
!Supportamaximummemorysize of 256MB(64Mbit technology) or
1GB(256Mbittechnology)SDRAM.
Slots
!One MR(Modem Riser) slot.
!Three 32-bit Master PCI Bus slots.
!Support 3.3v/5v PCI bus Interface.
On-BoardIDE
!AnIDEcontrollerontheSiS630EchipsetprovidesIDEHDD/CD-ROM
with PIO, Bus Master and Ultra DMA33/66 operation modes.
!Can connect up to four IDE devices.
CHAPTER 1CHAPTER 1
CHAPTER 1CHAPTER 1
CHAPTER 1 INTRODUCTIONINTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
1-3
On-BoardPeripherals
!On-BoardPeripheralsinclude:
- 1 floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M and
2.88Mbytes.
- 2 serial port
- 1 parallel port supports SPP/EPP/ECP mode
- 4 USB ports(2 USB rear ports + 2 USB front headers)
- 1 IrDA connector for SIR.
-1VGAport
- 1 Audio/Game Port
Video
!Chip integrated
!2D/3DGraphics
Audio
!Chip integrated
!AC’972.1Compliant
Network(optional)
!Chip integrated
- Plug and Play Compatible
- IEEE 802.3u Auto Negotiation and Parallel Detection for Automatic
Speed Selection
- Full Duplex and Half Duplex Mode for Both 10 and 100 Mbps
BIOS
!The mainboard BIOS provides “Plug & Play” BIOS which detects the
peripheral devices and expansion cards of the board automatically.
!The mainboard provides a Desktop Management Interface(DMI) function
which records your mainboard specifications.
Dimension
!Micro ATX Form Factor: 7.5” x 9” inches
Mounting
!6 mounting holes.
CHAPTER 1CHAPTER 1
CHAPTER 1CHAPTER 1
CHAPTER 1 INTRODUCTIONINTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
1-4
1.2 Mainboard Layout
PCI SLOT 3
PCI SLOT 2
PCI SLOT 1
ATX
Power Supply
SiS
630E
chipset
Socket 370
DIMM 2
Top: mouse
Bottom:
keyboard
DIMM 1
IDE2
B: USB
Ports
IDE1
FDD
JMDM1
JIR1
SYSFAN JFP1
USB1
JBAT1
JWOL1
JCD1
JAUX1
COM B
BATT
+
Top: LPT
Bottom:
COMA
VGAPort
Top: Midi/
GamePort
Bottom:
Line-Out
Line-In
Mic
MS-6189MICROATX SI1 Mainboard
JTEL1
MR
Winbond
83697HF
CPU FAN
BIOS
JCIG
CODEC
T:LAN Port
CHAPTER 2CHAPTER 2
CHAPTER 2CHAPTER 2
CHAPTER 2 HARDHARD
HARDHARD
HARDWW
WW
WARE INSTARE INST
ARE INSTARE INST
ARE INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
2-1
CPU
CPU
Chapter 2
HARDWARE INSTALLATION
2.1 Central Processing Unit: CPU
ThemainboardoperateswithIntel®CeleronTM/PentiumIII(FC-PGA)
processor. The mainboard uses a CPU socket called Socket 370 for easy
CPU installation. The CPU should always have a Heat Sink and a cooling
fan attached to prevent overheating.
3. Press the lever down to
complete the installation.
2. Locate Pin 1 in the socket
and look for the white dot or
cut edge in the CPU. Match
Pin 1 with the white dot/cut
edge. Then, insert the CPU.
It should insert easily.
OpenLever
Pin1
Sliding
Plate
White dot/
Cut edge
Close
Lever
1. Pull the lever sideways away
from the socket. Then, raise
the lever up to a 90-degree
angle.
Pin1
2.1-1 CPU Installation Procedures
CHAPTER 2CHAPTER 2
CHAPTER 2CHAPTER 2
CHAPTER 2 HARDHARD
HARDHARD
HARDWW
WW
WARE INSTARE INST
ARE INSTARE INST
ARE INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
2-2
2.1-2 CPU Core Speed Derivation Procedure
The mainboard CPU Core/Bus ratio and CPU Bus Frequency can
both be set through BIOS setup
If CPUClock = 100MHz
Core/Bus ratio = 4
then CPU core speed = Host Clock x Core/Bus ratio
= 100MHz x 4
= 400MHz
CHAPTER 2CHAPTER 2
CHAPTER 2CHAPTER 2
CHAPTER 2 HARDHARD
HARDHARD
HARDWW
WW
WARE INSTARE INST
ARE INSTARE INST
ARE INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
2-3
2.1-3 Fan Power Connectors: CPUFAN/SYSFAN
These connectors support system cooling fan with + 12V. It supports three
pin head connector. When connecting the wire to the connector, always
take note that the red wire is the positive and should be connected to the
+12V, the black wire is Ground and should be connected to GND. If your
mainboard has System Hardware Monitor chipset on-board, you must use a
specially designed fan with speed sensor to take advantage of this function.
For fans with fan speed sensor, every rotation of the fan will send out 2
pulses. System Hardware Monitor will count and report the fan rotation
speed.
Note: 1. Always consult vendor for proper CPU cooling fan.
2. CPU FAN supports the FAN control. You can install PC Alert
utility. This will automatically control the CPU FAN Speed according
to the actual CPU temperature.
3. During Suspend mode, FAN status can be set through BIOS.
CPUFAN:ProcessorFan
SYSFAN: System(Chassis) Fan
+12V
SENSOR
GND
SYSFAN
GND
+12V
SENSOR
CPUFAN
CHAPTER 2CHAPTER 2
CHAPTER 2CHAPTER 2
CHAPTER 2 HARDHARD
HARDHARD
HARDWW
WW
WARE INSTARE INST
ARE INSTARE INST
ARE INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
2-4
2.2 Clear CMOS Jumper: JBA2.2 Clear CMOS Jumper: JBA
2.2 Clear CMOS Jumper: JBA2.2 Clear CMOS Jumper: JBA
2.2 Clear CMOS Jumper: JBAT1T1
T1T1
T1
A battery must be used to retain the mainboard configuration in CMOS
RAM. Short 1-2 pins of JBAT1 to store the CMOS data.
Clear Data Keep Data
11
3
3
Note: You can clear CMOS by shorting 1-2 pin, while the system is off.
Then, return to 2-3 pin position. Avoid clearing the CMOS while
the system is on, it will damage the mainboard. Always unplug
the power cord from the wall socket.
22
JBAT1
1
3
CHAPTER 2CHAPTER 2
CHAPTER 2CHAPTER 2
CHAPTER 2 HARDHARD
HARDHARD
HARDWW
WW
WARE INSTARE INST
ARE INSTARE INST
ARE INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
2-5
2.3 Memory Installation2.3 Memory Installation
2.3 Memory Installation2.3 Memory Installation
2.3 Memory Installation
2.3-1 Memory Bank Configuration
Themainboardsupportsamaximummemorysizeof256MB(64-bittechnol-
ogy) or 1GB(256-bit technology) for SDRAM: It provides two 168-pin
unbuffered DIMMs (Double In-Line Memory Module) sockets. It supports
8 MB to 512 Mbytes DIMM memory module.
DIMM1(Bank0+ Bank1)
DIMM2(Bank2+Bank3)
CHAPTER 2CHAPTER 2
CHAPTER 2CHAPTER 2
CHAPTER 2 HARDHARD
HARDHARD
HARDWW
WW
WARE INSTARE INST
ARE INSTARE INST
ARE INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
2-6
A. HowtoinstallaDIMMModule
1. The DIMM slot has 2 Notch Keys “VOLT and DRAM”, so the
DIMM memory module can only fit in one direction.
2. Insert the DIMM memory module vertically into the DIMM slot.
Then push it in.
3. The plastic clip at the side of the DIMM slot will automatically
close.
Single Sided DIMM
Double Sided DIMM
VOLTDRAM
2.3-2 Memory Installation Procedures
Tabla de contenidos
Otros manuales de Placa madre de MSI
MSI
MSI H310M PRO-M2 PLUS Manual de usuario
MSI
MSI K9N6PGM2-V2 - Motherboard - Micro ATX Manual de usuario
MSI
MSI 945GZM3 Series Manual de usuario
MSI
MSI K9N2GM-FD - Motherboard - Micro ATX Manual de usuario
MSI
MSI B550M PRO/ A520M PRO Manual de usuario
MSI
MSI Z790-S01 Manual de usuario
MSI
MSI Z170A KRAIT GAMING Manual de usuario
MSI
MSI MS-6315 Manual de usuario
MSI
MSI MS-98L2 Manual de usuario
MSI
MSI GF615M Manual de usuario
MSI
MSI PRO X670-P WIFI Manual de usuario
MSI
MSI 875P Neo-FIS2R Manual de usuario
MSI
MSI PM8M2-V Series Manual de usuario
MSI
MSI X58 PRO MS-7522 Manual de usuario
MSI
MSI MS-7222 Manual de usuario
MSI
MSI H310M PRO-M2 Manual de usuario
MSI
MSI 661FM3-L Manual de usuario
MSI
MSI MS-6337 Manual de usuario
MSI
MSI X299 TOMAHAWK AC Manual de usuario
MSI
MSI MAG B660 TOMAHAWK WIFI DDR4 Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
