MRMC MRMC-2165-00 Manual de usuario
ii
Broadcast Jib Arm Quick Start Guide
QSG Product code: MRMC-2165-00
Product Covered: MRMC-2159-00
© 2022 Mark Roberts Motion Control ®Ltd. All rights reserved.
No part of this publication may be reproduced, transmitted, or translated
by any means — graphical, electronic, or mechanical — including
photocopying, recording, taping, or storage in an information retrieval
system, without the express written permission of Mark Roberts Motion
Control.
Although every care has been taken to ensure that the information in this
document is accurate and up to date, Mark Roberts Motion Control
continuously strives to improve their products and may make changes to
the hardware, firmware, and software described in this document. Mark
Roberts Motion Control therefore cannot be held responsible for any
error or omission in this document.
All product names mentioned herein are the trademarks or registered
trademarks of their respective owners.
Contact information
Mark Roberts Motion Control Ltd.
Unit 3, South East Studios
Blindley Heath
Surrey
RH7 6JP
United Kingdom
Telephone: +44 (0) 1342 838000
Web: www.mrmoco.com
www.mrmocorentals.com
Broadcast Jib Arm Quick Start Guide
iii
Broadcast Jib Arm Quick Start GuideBroadcast Jib ArmQuick Start Guide
Contents
Chapter 1 Quick Start..................................................................... 1
Overview ................................................................................. 1
Safety........................................................................................2
Tripod Safety .................................................................2
Mounting Jib Arm on Tripod ...............................................3
Connecting the Cables ..........................................................6
Jib Arm ..................................................................................8
Setting Jib Arm Weight: ...............................................8
Cable Adjustments........................................................9
Rotate Limits ...............................................................10
Jib Arm Limits.............................................................11
Appendix 1 Specifications............................................................... 14
Broadcast Jib Arm Quick Start Guide
iv
Broadcast Jib Arm Quick Start Guide
1
Broadcast Jib Arm Quick Start GuideBroadcast Jib ArmQuick Start Guide
Chapter 1 Quick Start
Overview
Thank you for using the Broadcast Jib Arm from Mark Roberts Motion
Control (MRMC). The Broadcast Jib Arm is designed for reliable day-in,
day out use in professional studio environments. The extremely quiet and
Jib Arm is controlled by MRMC’s Flair software with a capability to be
used with a PTZ type camera unit controlled using MRMC’s Polymotion
Chat software, is designed to help you achieve automated, smooth and
repeatable camera motions. It can handle a total payload of up to 4.2kg.
Broadcast Jib Arm has the following components:
A heavy duty tripod on which the jib arm system rests
Rotate Motor that rotates Jib am unit around tripod top plate
Jib arm, or “Height”, moves up and down by cable from
motorised cable drum
PTZ support platform to seat the PTZ camera unit
Heavy-duty tripod
Motorised Cable
Drum
Jib arm (“Hight”)
PTZ Support
Platform
E-stop each side
Rotor Motor
Broadcast Jib Arm Quick Start Guide
2
An emergency-stop (E-stop) button on each side
Safety
•Do not use around flammable gas. All electrical equipment can
generate sparks that can ignite flammable gas.
•Keep Away From Pets And Children. The track and camera heads
have powerful motors that can pinch, so take care not to get your
hands trapped in the gears or cabling.
•Keep the equipment dry. The system has not been made
weatherproof. Do not use with wet hands.
•Keep cables tidy. Use cable ties to keep them out of harm’s way, and
use the cable housing on the Jib arm to avoid running any cables
between the rotor motor and the PTZ.
•Do not insert hands and fingers in any crevices, especially when the
E-stop is released. The robot includes moving parts and motors and
can result in serious injury.
Tripod Safety
•Raise all three jacking feet well clear of the floor before moving.
•Drop all three jacking feet to make good contact with the floor when
parking, and lock off using the top nuts before using the boom in
robotic control.
Caution: Risk of toppling over! Do not roll the equipment close to
steps, ramps: must be used on smooth horizontal surfaces.
Caution: When using the rig under a ceiling or lintel, raise the boom
to the top before moving or stowing the boom, to keep it clear from
the surroundings and less chance of improper handling.Use buttons
provided before powering down.
Broadcast Jib Arm Quick Start Guide
3
Mounting Jib Arm on Tripod
1. Unpack the tripod and wheel it to a sturdy and levelled floor.
2. Two people lift the Jib Arm and thread the umbilical cable through
the centre cavity in the tripod.
Jacking foot
with
rectangular
locking nut
Broadcast Jib Arm Quick Start Guide
4
3. While aligning the screw cavities, seat the base of the arm on the
tripod.
4. Keep the arm firmly in position and tighten the 4 x M8 x 20 Cap
head screws to secure the arm to the base.
5. Attach the weight shaft to the arm using the screw supplied.
6. Add the weights and tighten the 2x weight clamps using the 4 x
screws.
7. Attach the Camera Support Platform to the arm using 2 x screws.
Weight Shaft
Weight Clamp
Screw o secure
weight shaft
Camera Support
Platform
Broadcast Jib Arm Quick Start Guide
5
Notes
Broadcast Jib Arm Quick Start Guide
6
Connecting the Cables
Cable
wrap
PTZ
Camera
SDI VIDEO
CAMERA ETH
CAMERA POWER
250VAC Power
24V PSU
Jib Arm
Connection
Jib Arm Ethernet
E-STOP
Note
Cable connections in the arm are done at the factory and must not
be modified.
Tabla de contenidos
Otros manuales de Robótica de MRMC
MRMC
MRMC CINEBOT Bolt Jr+ Manual de usuario
MRMC
MRMC Bolt Junior Manual de usuario
MRMC
MRMC PTA-1 Manual de usuario
MRMC
MRMC TX90L Manual de usuario
MRMC
MRMC MOVER RV13 Manual de usuario
MRMC
MRMC BROADCAST TALOS Manual de usuario
MRMC
MRMC Studiobot-165 Manual de usuario
MRMC
MRMC STUDIOBOT TX90 Manual de usuario
MRMC
MRMC CINEBOT MINI Manual de usuario
MRMC
MRMC UR10 ROBOT Mover Manual de usuario
Manuales populares de Robótica de otras marcas
STEMCenter USA
STEMCenter USA Pi-Bot v2.00 Manual de usuario
SunFounder
SunFounder PiDog Manual de usuario
Universal Robots
Universal Robots UR5 Manual de usuario
Universal Robots
Universal Robots E Series Manual de usuario
YASKAWA
YASKAWA MOTOMAN-MPL80 II Manual de usuario
EFORT
EFORT ECR5 Manual de instrucciones
