Moxa Technologies NPort IA5000 Series Manual de usuario
P/N: 1802051500216
*1802051500216*
NPort IA5150/5250 Series
Quick Installation Guide
Version 6.3, January 2021
Technical Support Contact Information
www.moxa.com/support
2021 Moxa Inc. All rights reserved.
- 2 -
Overview
NPort IA device servers deliver easy and reliable serial-to-Ethernet
connectivity for the industrial automation market. The servers support
several operation modes—TCP Server, TCP Client, UDP, Real COM, Pair
Connection, and Ethernet Modem—ensuring the compatibility of network
software, and they are an ideal choice for connecting RS-232/422/485
serial devices, such as PLCs, sensors, meters, motors, drives, barcode
readers, and operator displays. NPort IA device servers come with a
compact and rugged DIN-rail mountable casing.
Package Checklist
Before installing NPort IA device servers, verify that the package contains
the following items:
•1 NPort IA Series device server
•NPort IA Series quick installation guide
Optional Accessories
•DR-4524: 5W/2A DIN-rail 24 VDC power supply with universal 85 to
264 VAC input
•DR-75-24: 75W/3.2A DIN-rail 24 VDC power supply with universal
85 to 264 VAC input
•DR-120-24: 120W/5A DIN-rail 24 VDC power supply with 88 to 132
VAC/176 to 264 VAC input by switch
Note: Notify your sales representative if any of the above items are
missing or damaged.
NPort IA5150 Series Appearance
- 3 -
NPort IA5250 Appearance
Reset Button—Press the Reset button for 5 seconds to load factory
defaults. Use a pointed object, such as a straightened paper clip or
toothpick, to press the reset button. This will cause the Ready LED to blink
on and off. The factory defaults will be loaded once the Ready LED stops
blinking (after about 5 seconds). At this point, you should release the
reset button.
NPort IA LED Indicators (front panel)
Name
Color
Function
PWR1,PWR2
Red
Power is being supplied to power input PWR1,
PWR2.
Ready
Red
Steady on: Power is on, and the NPort IA is
booting up.
Blinking: Indicates an IP conflict, the DHCP or
BOOTP server did not respond properly
, or a relay
output occurred.
Green
Steady on: Power is on, and the NPort IA is
functioning normally.
Blinking: The device server has been located by
the Administrator’s Location function.
Off
Power is off, or a power-error condition exists.
Ethernet
Orange
10 Mbps Ethernet connection.
Green
100 Mbps Ethernet connection.
Off
Ethernet cable is disconnected, or has a short.
P1, P2
Orange
Serial port is receiving data.
Green
Serial port is transmitting data.
Off
No data is being transmitted or received through
the serial port.
FX Orange
Steady on: Ethernet fiber connection, but port is
idle.
Blinking: Fiber port is transmitting or receiving
data.
- 4 -
Hardware Installation Procedure
STEP 1: After removing the NPort IA from the box, the first thing you
should do is connect the power adapter. Connect the 12-48 VDC power
line with the NPort IA’s terminal block, or connect the DIN-rail power
supply with the NPort IA’s terminal block.
STEP 2: Connect the NPort IA to a network. Use a standard
straight-through Ethernet cable to connect to a hub or switch. When
setting up or testing the NPort IA, you might find it convenient to connect
directly to your computer’s Ethernet port. In this case, use a crossover
Ethernet cable.
STEP 3: Connect the NPort IA’s serial port to a serial device.
STEP 4: The NPort IA is designed to be attached to a DIN rail or mounted
on a wall. The two sliders on the NPort IA’s rear panel serve a dual
purpose. For wall mounting, both sliders should be extended. For DIN-rail
mounting, start with one slider pushed in, and the other slider extended.
After attaching the NPort IA on the DIN rail, push the extended slider in to
lock the device server to the rail. The two placement options are
illustrated in the accompanying figures.
Wallmount DIN Rail
Software Installation Information
For the NPort’s configuration, the default IP address of the NPort is: LAN:
Static; IP = 192.168.127.254; netmask = 255.255.255.0.
NOTE
If you have forgotten the NPort's IP address, use the Device
Search Utility (DSU) from your PC to locate the NPort. After
searching the LAN for NPort units, the DSU will display the IP
address of each unit.
You may log in with the password moxa to change any setting to meet
your network topology (e.g., IP address) or serial device (e.g., serial
parameters). For first-time use, click the Wizard in the left navigation
panel. The wizard will prompt you to configure the IP address, SSID, and
security mode. For other settings, use the factory defaults or modify the
settings for your application.
For software installation, download the relative utilities from Moxa's
website:
- 5 -
https://www.moxa.com/support/support_home.aspx?isSearchShow=1
•Download the NPort Windows Driver Manager and install it as the
driver to run with Real COM mode of the NPort Series.
•Execute NPort Windows Driver Manager; then map the virtual COM
ports on your Windows platform.
•You may refer to the DB9 Male Ports pin assignment section to loop
back pin 2 and pin 3 for the RS-232 interface to carry out a self test on
the device.
•Use HyperTerminal or a similar program (you may download Moxa's
program, called PComm Lite) to test whether the device is good or
not.
Pin Assignments and Cable Wiring
RS-232/422/485 (Male DB9) Pinouts
PIN
RS-232
RS-422/RS-485 (4W)
RS-485 (2W)
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
4W/2W RS-485/RS-422 (Terminal Block) Pinouts
PIN RS-485 (2W)
RS-422/
RS-485 (4W)
1
–
TxD+(B)
2
–
TxD-(A)
3
Data+(B)
RxD+(B)
4
Data-(A)
RxD-(A)
5
–
GND
Four cables are available as optional accessories that can be used to
connect the NPort IA to RS-232 serial devices. For your convenience, we
show precise cable wiring diagrams for each of the two cables.
- 6 -
Female DB9 to Male DB9
Female DB9 to Male DB25
ATEX and IECEx Information
1. Certificate number: DEMKO 07 ATEX 0690059x
2. Ambient range (-40°C ≤ Tamb ≤ 75°C)
3. Certification string (Ex nA IIC T3)
4. Standards covered (EN60079-0:2006, EN60079-15:2005, IECEx UL
13.0023X, IEC 60079-0 Ed. 6, IEC 60079-15 Ed. 4)
5. Conditions of safe usage:
The Ethernet Communication Devices are to be mounted in an IP54
enclosure and used in an area with a pollution degree of not more
than 2, as defined by IEC 60664-1.
A 4-mm2conductor must be used when a connection to the external
grounding screw is utilized.
Conductors suitable for use in an ambient temperature of 114°C must
be used for the Power Supply Terminal.
Provisions shall be made, either in the apparatus or external to the
apparatus, to prevent the rated voltage to exceed the transient
disturbance by more than 40%.
Este manual sirve para los siguientes modelos
7
Tabla de contenidos
Otros manuales de Servidor de Moxa Technologies
Moxa Technologies
Moxa Technologies FLI-1200 Series Manual de usuario
Moxa Technologies
Moxa Technologies NPort 5200-P Series Manual de usuario
Moxa Technologies
Moxa Technologies NPort W2250A-T-EU Manual de usuario
Moxa Technologies
Moxa Technologies CN2500 Manual de usuario
Moxa Technologies
Moxa Technologies NPort IA5000A-I/O series Manual de usuario
Moxa Technologies
Moxa Technologies NPort 6650 Manual de usuario
Moxa Technologies
Moxa Technologies MIINEPORT E1 Manual de usuario
Moxa Technologies
Moxa Technologies NPort 6450 Series Manual de usuario
Moxa Technologies
Moxa Technologies CN2600 Series Manual de usuario
Moxa Technologies
Moxa Technologies NPort IA5250I/5250I-T Series Manual de usuario
Moxa Technologies
Moxa Technologies NPort P5150A Series Manual de usuario
Moxa Technologies
Moxa Technologies ioLogik R2140 Manual de usuario
Moxa Technologies
Moxa Technologies NPort 5600-8-DT Manual de usuario
Moxa Technologies
Moxa Technologies NPort 5600-8-DTL Series Manual de usuario
Moxa Technologies
Moxa Technologies NPort 5230 Manual de usuario
Moxa Technologies
Moxa Technologies ioLogik E1210 Manual de usuario
Moxa Technologies
Moxa Technologies NPort 5610 series Manual de usuario
Moxa Technologies
Moxa Technologies NPort 5600 Series Manual de usuario
Moxa Technologies
Moxa Technologies ioLogik 4000 Series Manual de usuario
Moxa Technologies
Moxa Technologies NPort Server Lite DE-302 Manual
