Moxa Technologies IoLogik E1210 Manual de usuario

– 1 – – 2 – – 3 –

P/N: 1802012001011

ioLogik E1200 Series

Quick Installation Guide

Second Edition, February 2011

1. Overview

The ioLogik E1200 series comes with 2 embedded Ethernet switch

ports that can form a daisy-chain topology, which is the easiest

way to add more Ethernet devices to a network or connect your

ioLogiks in series. Moxa’s free Active OPC Server offers active (or

“push”) communication that works between Moxa’s ioLogik units

and HMI/SCADA systems, providing instant I/O status reports by

“Active Tags.” The event-driven active tags result in an I/O

response time that is 7 times faster than other OPC Server

packages and an 80% reduction in network traffic.

Model Selection:

ioLogik

DIO

Relay

RTD

E1210

–

E1211

–

E1212

–

E1214

–

E1240

–

E1241

–

E1242

–

E1260

–

E1262

–

Package Checklist

•1 ioLogik E1200 series remote I/O product

•Documentation and software CD

•Quick installation guide (printed)

2. Specifications

System

Ethernet:

2 x 10/100 Mbps switch ports, RJ45

Protection:

1.5 KV magnetic isolation

Protocols:

Modbus/TCP, TCP/IP, UDP, DHCP, Bootp,

HTTP

Power Input:

24 VDC nominal, 12 to 36 VDC

Wiring:

I/O cable max. 14 AWG

Dimensions:

27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in)

Weight:

under 200 g

Operating

Temperature:

Standard Models: -10 to 60°C (14 to

140°F)

Operating

Temperature:

Wide Temperature Models: -40 to 75°C

(-40 to 167°F)

Storage Temperature:

-40 to 85°C (-40 to 185°F)

Ambient Relative

Humidity:

5 to 95% (non-condensing)

Altitude:

Up to 2000 m

Note: Please contact Moxa if you require products guaranteed to

function properly at higher altitudes.

Standards and

Certifications:

UL 508, CE, FCC Class A

Warranty Period:

5 years (excluding ioLogik E1214*)

Details:

See www.moxa.com/warranty

*Because of the limited lifetime of power relay, products that use

this component are covered by a 2-year warranty.

Digital Input

Sensor Type:

NPN, PNP, and Dry contact

I/O Mode:

DI or Event Counter

Dry Contact:

• Logic 0: short to GND

• Logic 1: open

Wet Contact:

• Logic 0: 0 to 3 VDC

• Logic 1: 10 to 30 VDC (DI COM to DI)

Isolation:

3K VDC or 2K Vrms

Counter/Frequency:

250 Hz, power off storage

Digital Output

I/O Mode:

DO or Pulse Output

Pulse Wave

Width/Frequency:

1 ms/500 Hz

Over-voltage

Protection:

45 VDC

Over-current

Protection:

2.6 A (4 channels @650 mA)

Over-temperature

Shutdown:

175°C (typical), 150°C (min.)

Current Rating:

200 mA per channel

Isolation:

3K VDC or 2K Vrms

Relay Output

Type:

Form A (N.O.) relay outputs, 5A

Contact Rating:

5 A @ 30 VDC, 5 A @ 250 VAC, 5 A @ 110

VAC

Inductance Load:

2 A

Resistance Load:

5 A

Breakdown Voltage:

500 VAC

Relay On/Off Time:

1500 ms (Max.)

Initial Insulation

Resistance:

1G min. @ 500 VDC

Expected Life:

100,000 times (Typical)

Initial Contact

Resistance:

30 milli-ohms (Max.)

Pulse Output:

0.3 Hz at rated load

Analog Input

Type:

Differential input

Resolution:

16 bits

I/O Mode:

Voltage / Current

Input Range:

0 to 10 VDC, 4 to 20 mA

Accuracy:

±0.1% FSR @ 25°C

±0.3% FSR @ -10 and 60°C

±0.5% FSR @ -40 and 75°C

Sampling Rate (all

channels):

12 samples/sec

Input Impedance:

10M ohms (minimum)

Built-in Resistor for

Current Input:

120 ohms

Analog Output

Resolution:

12 bits

Output Range:

0 to 10 VDC, 4 to 20 mA

Voltage Output:

10 mA (Max.)

Accuracy:

±0.1% FSR @ 25°C

±0.3% FSR @ -40 and 75°C

Load Resistor:

• Internal power: 400 ohms

• External 24V power: 1000 ohms

RTD

Input Type:

PT50, PT100, PT200, PT500, PT1000;

Resistance of 10

ohms, 20 ohms, and 100

ohms

Sampling Rate:

12 samples/sec (all channels)

Resolution:

16 bits

Accuracy:

±0.1% FSR @ 25°C

±0.3% FSR @ -40 and 75°C

Input Impedance:

625K ohms

Thermocouple Input

Sensor Type:

J, K, T, E, R, S, B, N

Mili Volt Type:

±78.126 mV, ±39.062 mV, ±19.532 mV

Fault and Overvoltage

protection:

±35 VDC (power off); +30 VDC, -25 VDC

(power on)

Sampling Rate:

12 samples/sec (all channels)

Resolution:

16 bits

Accuracy:

±0.1% FSR @ 25°C

±0.3% FSR @ -40 and 75°C

Input Impedance:

10M ohms

3. Installation

Power and Networking

Connect the +12 to +36 VDC power line to the ioLogik E1200’s

terminal block V+ terminal; connect the ground from the power

supply to the V- terminal. Connect the ground pin ( ) if earth

ground is available.

– 4 – – 5 – – 6 –

www.moxa.com/support

The Americas:

+1-714-528-6777 (toll-free: 1-888-669-2872)

Europe:

+49-89-3 70 03 99-0

Asia-Pacific:

+886-2-8919-1230

China:

+86-21-5258-9955 (toll-free: 800-820-5036)

NOTE

For safety reasons, the wires attached to the power should

be at least 2 mm in diameter.

Jumper Settings

The models with DIO or AI channels require configuring the

jumpers inside the enclosure. Remove the screw located on the

back panel and open the cover to configure the jumpers.

DIO mode configuration is

shown to the right (default: DO

Mode).

Analog mode configuration is

shown to the right

(default:

Voltage Mode).

Mounting

The ioLogik E1200 is designed with a vertical form factor, and can

be used with both DIN-Rail and wall mounting applications. When

mounting on a rail, release the bottom mounting kit, install the

ioLogik on the rail, and then restore the bottom mounting kit to fix

the ioLogik to the rail. When using wall mounting, release both the

upper and bottom DIN-Rail kits.

The ioLogik E1200 has two built-in Ethernet switch ports for

connecting either a standard direct or cross-over Ethernet cable to

either RJ45 port.

LED Indicators

Type

Color

Description

Power

Amber

System power is ON

Off

System power is OFF

Ready

Green

System is ready

Flashing

Flashes every 1 sec when the “Locate” function is

triggered

Flashing

Flashes every 0.5 sec when the firmware is being

upgraded

Flashing

An on/off period cycle: 0.5 second shows “Safe

Mode”

Off

System is not ready.

Port 1

Green

Ethernet connection enabled

Flashing

Transmitting or receiving data

Port 2

Green

Ethernet connection enabled

Flashing

Transmitting or receiving data

4. I/O Wiring

Digital Input/Output (Sink Type)

Analog Input

Relay Output (Form A)

RTD Input

TC input

5. System Configuration

Configuration via Web Console

Main configuration of an ioLogik E1200 is via its web console.

•Default IP Address: 192.168.127.254

•Subnet Mask: 255.255.255.0

Note: Be sure to configure the host PC’s IP address to the same

subnet as the ioLogik E1200. For example, 192.168.127.253

ioSearch Utility

ioSearch is a search utility that helps users locate an ioLogik E1200

on the local network. The utility can be found in the Document and

Software CD Software ioSearch; the latest version can be

downloaded from Moxa’s website.

Load Factory Default Settings

There are three ways to restore the ioLogik E1200 to the factory

default settings.

1. Hold the RESET button for 5 seconds.

2. Right click the specified ioLogik in the ioSearch utility and

select “Reset to Default.”

3. Select “Load Factory Default” from the web console.

Modbus Address Table

Please refer to the user’s manual for details of the ioLogik’s

Modbus address, or refer to the start address of the I/O channels in

web console User-defined Modbus Addressing Default

Address.

Active OPC Server Connection

Take the following steps to connect the ioLogik E1200 to an Active

OPC Server:

1. Disable the user-defined Modbus address function.

2. Install the Active OPC Server Lite Package from Document and

Software CD Software AOPC Lite ActiveOPCSetup 

Install.exe

3. Install from Web console Active OPC Server Settings 

AOPC & I/O Settings; specify the IP address where the Active

OPC Server is installed. Specify the I/O channels that need to

be added to Active OPC Server Lite. Submit the settings and

then Save/Restart.

4. From web console Active OPC Server Settings Create

AOPC Tag, click the “Create Tag” button.

5. Launch Active OPC Server Lite from Start Programs MOXA

IOServer ActiveOPC ActiveOPC. Save the configuration

before exiting the Active OPC Server Lite program.

Otros manuales para ioLogik E1210

Este manual sirve para los siguientes modelos

Otros manuales de Sistema de E/S de Moxa Technologies

Moxa Technologies

Moxa Technologies ioLogik E2212 Manual de usuario

Moxa Technologies

Moxa Technologies MC-7270-DC-CP-T Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik R1210 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik 1300 Series Manual

Moxa Technologies

Moxa Technologies ioLogik 2542 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1500-T Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E4200 Manual de usuario

Moxa Technologies

Moxa Technologies DA-IRIGB-4DIO-PCI104-EMC4 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E2210 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1211 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1210 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1210 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E2260 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E2200 Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik 2500 Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1261H Manual de usuario

Moxa Technologies

Moxa Technologies ioThinx 4510 Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik 2500 Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E2242 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Manual de usuario

Moxa Technologies

Moxa Technologies ioThinx 4510 Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E4200 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1500 Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E2242 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario