Motorola M68MPB16Z1 Manual de usuario
M68MPB16Z1UM/D
REV 1
March 1998
M68MPB16Z1
MCU PERSONALITY BOARD
USER’S MANUAL
© MOTOROLA, INC., 1994, 1998; All Rights Reserved
Motorola reserves the right to make changes without further notice to any products herein to
improve reliability, function or design. Motorola does not assume any liability arising out of the
application or use of any product or circuit described herein; neither does it convey any license
under its patent rights nor the rights of others. Motorola products are not designed, intended, or
authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should
Buyer purchase or use Motorola products for any such unintended or unauthorized application,
Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney
fees arising out of, directly or indirectly, any claim of personal injury or death associated with
such unintended or unauthorized use, even if such claim alleges that Motorola was negligent
regarding the design or manufacture of the part.
Motorola and the Motorola logo are registered trademarks of Motorola Inc.SDI is a trademark of
Motorola Inc.
Motorola Inc. is an Equal Opportunity/Affirmative Action Employer.
CONTENTS
M68MPB16Z1UM/D iii
CONTENTS
CHAPTER 1 GENERAL INFORMATION
1.1 INTRODUCTION............................................................................................................. 1-1
1.2 SPECIFICATIONS........................................................................................................... 1-2
1.3 EQUIPMENT REQUIRED............................................................................................... 1-2
1.4 CUSTOMER SUPPORT .................................................................................................. 1-3
CHAPTER 2 HARDWARE PREPARATION AND INSTALLATION
2.1 INTRODUCTION............................................................................................................. 2-1
2.2 HARDWARE PREPARATION....................................................................................... 2-1
2.2.1 Clock Select Header (W1)......................................................................................... 2-4
2.2.2 VDDA Select Header (W2)....................................................................................... 2-5
2.2.3 Voltage Reference High Select Header (W3)............................................................ 2-6
2.2.4 Voltage Reference Low Select Header (W4)............................................................. 2-7
2.2.5 VSSA Insertion Point (E1) ........................................................................................ 2-7
2.3 MEVB CONFIGURATION.............................................................................................. 2-8
2.4 ACTIVE PROBE CONFIGURATION........................................................................... 2-10
CHAPTER 3 MEVB QUICK START GUIDE
3.1 INTRODUCTION............................................................................................................. 3-1
3.2 CONFIGURING THE MPFB........................................................................................... 3-1
3.2.1 MPFB Memory Devices............................................................................................ 3-1
3.2.2 MPFB Jumper Headers.............................................................................................. 3-2
3.3 MEVB INSTALLATION INSTRUCTIONS.................................................................... 3-3
3.3.1 Power Supply – MPFB Connection........................................................................... 3-4
3.3.2 Personal Computer – BDM Connection.................................................................... 3-5
3.4 SOFTWARE INSTALLATION AND MCU INITIALIZATION.................................... 3-5
CHAPTER 4 MEVB SUPPORT INFORMATION
4.1 INTRODUCTION............................................................................................................. 4-1
4.2 LOGIC ANALYZER CONNECTOR SIGNALS............................................................. 4-1
CONTENTS
iv M68MPB16Z1UM/D
CHAPTER 5 MAPI SUPPORT INFORMATION
5.1 INTRODUCTION............................................................................................................. 5-1
5.2 MAPI BUS CONNECTORS ............................................................................................ 5-1
CHAPTER 6 SCHEMATIC DIAGRAMS
6.1 INTRODUCTION............................................................................................................. 6-1
FIGURE
2-1. MPB Parts Location Diagram (top view).......................................................................... 2-2
2-2. MPB – MPFB Interconnection (with SDI interface connector)........................................ 2-9
2-3. Active Probe Interconnection (with Active Probe Box) ................................................. 2-11
5-1. MAPI Interface Connector Layout.................................................................................... 5-1
5-2. MAPI Interface Connector P1 Pin Assignments............................................................... 5-2
5-3. MAPI Interface Connector P2 Pin Assignments............................................................... 5-3
5-4. MAPI Interface Connector P3 Pin Assignments............................................................... 5-4
5-5. MAPI Interface Connector P4 Pin Assignments............................................................... 5-5
TABLES
1-1. MPB Specifications........................................................................................................... 1-2
2-1. Jumper Header Types........................................................................................................ 2-3
2-2. MPB Jumper Header Descriptions.................................................................................... 2-3
3-1. MPFB Quick Start Jumper Header Configuration............................................................ 3-2
4-1. Logic Analyzer Connector J7 Pin Assignments................................................................ 4-2
4-2. Logic Analyzer Connector J8 Pin Assignments................................................................ 4-2
4-3. Logic Analyzer Connector J9 Pin Assignments................................................................ 4-3
4-4. Logic Analyzer Connector J10 Pin Assignments.............................................................. 4-3
4-5. Logic Analyzer Connector J11 Pin Assignments.............................................................. 4-4
4-6. Logic Analyzer Connector J12 Pin Assignments.............................................................. 4-4
4-7. Logic Analyzer Connector J13 Pin Assignments.............................................................. 4-6
4-8. Logic Analyzer Connector J14 Pin Assignments.............................................................. 4-8
4-9. Logic Analyzer Connector J15 Pin Assignments.............................................................. 4-9
4-10. Logic Analyzer Connector J16 Pin Assignments.............................................................. 4-9
4-11. Logic Analyzer Connector J17 Pin Assignments............................................................ 4-10
4-12. Logic Analyzer Connector J18 Pin Assignments............................................................ 4-11
4-13. Logic Analyzer Connector J19 Pin Assignments............................................................ 4-12
4-14. Logic Analyzer Connector J20 Pin Assignments............................................................ 4-12
GENERAL INFORMATION
M68MPB16Z1UM/D 1-1
CHAPTER 1
GENERAL INFORMATION
1.1 INTRODUCTION
This manual provides general information, hardware preparation, installation
instructions, a quick start guide, and support information for the M68MPB16Z1
MCU Personality Board (MPB). The MPB is one component of Motorola’s
modular approach to MC68HC16Z1 Microcontroller Unit-based product
development. This modular approach lets you easily configure our development
systems to fit your requirements.
The MPB may be used in either the MMDS1632 Motorola Modular Development
System (MMDS) or the modular evaluation board (MEVB). The MEVB consists
of the M68MPFB Modular Platform Board (MPFB) and an MPB. Alternately, you
may install the MPB directly in your target system if the target system includes a
modular active probe interconnect (MAPI) interface. The MCU device on the
MPB defines which MCU is emulated/evaluated by the MMDS or evaluated by
the MEVB. Both systems are invaluable tools for designing, debugging, and
evaluating MCU operation of the M68HC12, M68HC16, and M68300 MCU
families. By providing the essential MCU timing and I/O circuitry, these systems
simplify user evaluation of prototype hardware/software products.
The MPB includes:
• M68MPB16Z1 MCU Personality Board (MPB)
• Plastic overlay for use with the MEVB – pin outs for the logic analyzer
connectors on the MPFB (specifically for the MC68HC16Z1 MCU)
• Documentation (this manual)
GENERAL INFORMATION
1-2 M68MPB16Z1UM/D
1.2 SPECIFICATIONS
Table 1-1 lists MPB specifications.
Table 1-1. MPB Specifications
Characteristic Specifications
On-Board Clock Case style: 14- or 8-pin hybrid crystal clock oscillator
(frequency as required by MCU).
External Clock 32 KHz – 16.78 MHz (or maximum MCU allows).
MCU I/O ports HCMOS compatible
Temperature
Operating
Storage 0° to +40° C
-40° to +85° C
Relative humidity 0 to 90% (non-condensing)
Power requirements +5Vdc ± 5% @ 500 mA (max.)
Dimensions
MCU Personality Board 3.25 x 3.25 in. (82.6 x 82.6 mm)
1.3 EQUIPMENT REQUIRED
The external requirements for MPB operation are either an MEVB or MMDS
system. For MMDS operation requirements, see the MMDS1632 Motorola
Modular Development System User’s Manual,MMDS1632UM/D. For operation
requirements for the MEVB, see this manual and the M68MPFB Modular
Platform Board User’s Manual,M68MPFBUM/D.
GENERAL INFORMATION
M68MPB16Z1UM/D 1-3
1.4 CUSTOMER SUPPORT
For information about a Motorola distributor or sales office near you call:
AUSTRALIA, Melbourne – (61-3)887-0711
Sydney – 61(2)906-3855
BRAZIL, Sao Paulo – 55(11)815-4200
CANADA, B. C., Vancouver – (604)606-8502
ONTARIO, Toronto – (416)497-8181
ONTARIO, Ottawa – (613)226-3491
QUEBEC, Montreal – (514)333-3300
CHINA, Beijing – 86-10-68437222
DENMARK – (45)43488393
FINLAND, Helsinki – 358-9-6824-400
FRANCE, Paris – 33134 635900
GERMANY,
Langenhagen/Hannover – 49(511)786880
Munich – 49 89 92103-0
Nuremberg – 49 911 96-3190
Sindelfingen – 49 7031 79 710
Wiesbaden – 49 611 973050
HONG KONG, Kwai Fong – 852-6106888
Tai Po – 852-6668333
INDIA, Bangalore – (91-80)5598615
ISRAEL, Herzlia – 972-9-590222
ITALY, Milan – 39(2)82201
JAPAN, Fukuoka – 81-92-725-7583
Gotanda – 81-3-5487-8311
Nagoya – 81-52-232-3500
Osaka – 81-6-305-1802
Sendai – 81-22-268-4333
Takamatsu – 81-878-37-9972
Tokyo – 81-3-3440-3311
KOREA, Pusan – 82(51)4635-035
Seoul – 82(2)554-5118
MALAYSIA, Penang – 60(4)2282514
MEXICO, Mexico City – 52(5)282-0230
Guadalajara – 52(36)21-8977
PUERTO RICO, San Juan – (809)282-2300
SINGAPORE – (65)4818188
SPAIN, Madrid – 34(1)457-8204
SWEDEN, Solna – 46(8)734-8800
SWITZERLAND, Geneva – 41(22)799 11 11
Zurich – 41(1)730-4074
TAIWAN, Taipei – 886(2)717-7089
THAILAND, Bangkok – 66(2)254-4910
UNITED KINGDOM, Aylesbury – 441(296)395-252
UNITED STATES, Phoenix, AZ – 1-800-441-2447
For a list of the Motorola sales offices and distributors:
http://www.mcu.motsps.com/sale_off.html
GENERAL INFORMATION
1-4 M68MPB16Z1UM/D
HARDWARE PREPARATION AND INSTALLATION
M68MPB16Z1UM/D 2-1
CHAPTER 2
HARDWARE PREPARATION AND INSTALLATION
2.1 INTRODUCTION
This chapter provides unpacking instructions, hardware preparation information,
and installation instructions for the MPB.
When you unpack the MPB from its shipping carton, verify that all items are in
good condition. Save packing material for storing and shipping the MPB.
NOTE
Should the MPB arrive damaged, save all packing material, and
contact the carrier’s agent.
2.2 HARDWARE PREPARATION
This portion of the manual explains how to prepare the MPB before use, as well
as how to configure the MPB for system operation.This section also explains
MPB installation in the MMDS and MEVB.
The MPB has been factory tested and is shipped with installed jumpers. A jumper
installed on a jumper header provides a connection between two points in the
MPB circuit. The MPB has two types of jumper headers: three-pin and two-pin
with a cut-trace short. A cut-trace short has a copper trace between the feed-
through holes (bottom or solder side of the MPB). Table 2-1 describes each type
of jumper header.
The MPB has four jumper headers (for which Table 2-2 is a quick reference
guide). You may reconfigure these jumper headers to customize MPB
functionality. The following paragraphsexplain each jumper header function.
There is also an insertion point (E1) for connecting an external ground.
NOTE
Verify that all socketed parts are seated in their sockets.
HARDWARE PREPARATION AND INSTALLATION
2-2 M68MPB16Z1UM/D
CAUTION
Depending on your application, it may be necessary to cut the W2
wiring trace short (cut-trace short). Be careful not to cut adjacent
PCB traces, nor cut too deep into the multi-layer circuit board.
If the cut-trace short on a jumper header is already cut, you can
return the MPB to its default setting by installing a user-supplied
fabricated jumper.
MPB16Z1B
01 - RE90378W
C1 + + C2
R2
C3
Y1
C5
W1
REV
R1
L2
L1
U1
MC68HC16Z1
S/ N
C4
RN2
C12 + RN3 R3
R4
C14
C15
C16
C17
C18
+ C13
RN1
C8 C7
C6 C9
L4
L5 W4
W3
L3
C10
C11
© 1993
ReferenceMark
MCU
Clock
Source
VDDA
Source
VRH Source
External
Ground
Connection VRLSource
W2
E1
Figure 2-1. MPB Parts Location Diagram (top view)
Tabla de contenidos
Otros manuales de Hardware de computadora de Motorola
Motorola
Motorola HC12 Manual de usuario
Motorola
Motorola MC68306 Manual de usuario
Motorola
Motorola DigitalDNA ColdFire MCF5272 Manual de usuario
Motorola
Motorola MVME5100 Series Manual de usuario
Motorola
Motorola MC68030 Manual de usuario
Motorola
Motorola SPX3BUM/D Manual de usuario
Motorola
Motorola 68000 Manual de usuario
Motorola
Motorola CME-12D60 Manual de usuario
Motorola
Motorola MC68302 Manual de usuario
Motorola
Motorola MC6805R Series Manual del propietario
Motorola
Motorola MVME712C Guía
Motorola
Motorola MPC8260 PowerQUICC II Manual de usuario
Motorola
Motorola 56F805 Instrucciones de uso
Motorola
Motorola 68000 Guía de configuración
Motorola
Motorola M68MPB916X1 Manual de usuario
Motorola
Motorola 68HC12 Manual de usuario
Motorola
Motorola CPU32 Manual de usuario
Motorola
Motorola MMCMPFB1200 Manual de usuario
Motorola
Motorola MPC823e Manual de usuario
Motorola
Motorola MPC564EVB Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
