Motorola Symbol LS1203 Manual de usuario
Symbol LS1203
Quick Reference Guide
2 Symbol LS1203
©2006-2008 MOTOROLA, INC. All rights
reserved.
Motorola reserves the right to make changes
to any product to improve reliability, function,
or design.
Motorola does not assume any product liability
arising out of, or in connection with, the
application or use of any product, circuit, or
application described herein.
No license is granted, either expressly or by
implication, estoppel, or otherwise under any
patent right or patent, covering or relating to
any combination, system, apparatus,
machine, material, method, or process in
which Motorola products might be used. An
implied license exists only for equipment,
circuits, and subsystems contained in Motorola
products.
MOTOROLA, the Stylized M Logo and Symbol
and the Symbol logo are registered
trademarks of Motorola, Inc. Other product
names mentioned in this manual may be
trademarks or registered trademarks of their
respective companies and are hereby
acknowledged.
Motorola, Inc.
One Motorola Plaza
Holtsville, N.Y. 11742-1300
http://www.motorola.com/enterprisemobility
Warranty
For the complete Motorola hardware product
warranty statement, go to:
http://www.motorola.com/enterprisemobility/warranty
Patents
This product is covered by one or more
patents. For patent information go to:
http://www.motorola.com/enterprisemobility/patents
3
Connect/Disconnect
Cable
Connect Host Interface
Keyboard Wedge Interface
RS-232 Interface
USB Interface
1
2
4 Symbol LS1203
Aim and Scan
3
012345 012345
6 Symbol LS1203
Parts of the Scanner
Scanning Modes
The scanner can operate in two modes:
•
Triggered mode - trigger button must be
pressed to emit the laser in order to a
scan bar code.
or
•
Auto-scan mode - scanner laser is in
constant on state and no trigger button
press is required to scan a bar code.
To toggle between modes, scan
TRIGGERED/AUTO-SCAN bar codes on
page 5.
For example, if the scanner is in triggered
mode, scan AUTO-SCAN MODE to switch
to auto-scan mode. If the scanner is in
auto-scan mode, scan TRIGGERED
MODE to switch to triggered mode.
NOTE When the scanner is
not used for an extended
period of time in auto-scan
mode, it enters sleep mode.
To wake the scanner, press
the trigger button.
LED
Trigger
Button
Scan
Window
7
Troubleshooting
Problem Possible
Cause Possible
Solutions
Nothing
happens
when the
scan button
is pulled.
No power to
the scanner.
Check system
power. Ensure
power supply is
connected.
Interface or
power
cables are
loose.
Ensure all cable
connections are
secure.
Laser
comes on,
but symbol
does not
decode.
Scanner not
programmed
for correct
bar code
type.
Ensure scanner
is programmed
to read the type
of bar code
scanned. Refer
to the Symbol
LS1203
Product
Reference
Guide, p/n
72E-73953-xx,
for more
information.
Bar code
symbol is
unreadable.
Check the
symbol to
ensure it is not
defaced. Try
scanning
another bar
code type.
Distance
between
scanner and
bar code is
incorrect.
Move scanner
closer to or
further from the
bar code.
Symbol is
decodedbut
not
transmitted
to the host.
Scanner not
programmed
for the
correct host
type.
Scan the
appropriate
host type bar
code.
8 Symbol LS1203
Beeper Definitions
The scanner issues different beep
sequences and patterns to indicate status.
The table below defines beep sequences
that occur during both normal scanning and
while programming the scanner.
NOTE For detailed
troubleshooting, refer to the
Symbol LS1203 Product
Reference Guide, p/n
72E-73953-xx.
Beeper
Sequence Indication
Standard Use
Low/medium/high
beep
Power up.
Short high beep A bar code symbol was
decoded (if decode beeper
is enabled).
4 long low beeps A transmission error was
detected in a scanned
symbol. The data is
ignored. This occurs if a
unit is not properly
configured. Check option
setting.
5 low beeps Conversion or format
error.
Low/high/low
beep
ADF transmit error.
High/high/high/
low beep
RS-232 receive error.
Parameter Menu Scanning
Short high beep Correct entry scanned or
correct menu sequence
performed.
9
Low/high beep Input error, incorrect bar
code or Cancel scanned,
wrong entry, incorrect bar
code programming
sequence; remain in
program mode.
High/low beep Keyboard parameter
selected. Enter value
using bar code keypad.
High/low/high/
low beep
Successful program exit
with change in the
parameter setting.
Low/high/low/
high beep
Out of host parameter
storage space. Scan SET
DEFAULTS on page 86.
Code 39 Buffering
High/low beep New Code 39 data was
entered into the buffer.
3 beeps - long
high beep
Code 39 buffer is full.
Low/high/low
beep
The Code 39 buffer was
erased or there was an
attempt to clear or transmit
an empty buffer.
Low/high beep A successful transmission
of buffered data.
Host Specific
USB only
4 short high
beeps
Scanner has not
completed initialization.
Wait several seconds and
scan again.
Scanner gives a
power-up beep
after scanning a
USB Device
Type.
Communication with the
bus must be established
before the scanner can
operate at the highest
power level.
Beeper
Sequence Indication
10 Symbol LS1203
LED Definitions
In addition to beeper sequences, the
scanner communicates with the user using
a two-color LED display. The table below
defines LED colors that display during
scanning.
Programming Bar Codes
Descriptions
This guide includes the programming bar
codes required to set up the scanner to
work with various host interfaces. Some
frequently used programming bar codes
are also included.
For all programming bar codes and detailed
information about the scanner, go to:
http://www.symbol.com/services/manuals
The power-up
beep occurs
more than once.
The USB bus may put the
scanner in a state where
power to the scanner is
cycled on and off more
than once. This is normal
and usually happens when
the host PC cold boots.
RS-232 only
1 short high beep A <BEL> character is
received and Beep on
<BEL> is enabled.
LED Indication
Off No power is applied to the scanner,
or the scanner is on and ready to
scan.
Green A bar code was successfully
decoded.
Red A data transmission error or
scanner malfunction occurred.
Beeper
Sequence Indication
Otros manuales para Symbol LS1203
2
Tabla de contenidos
Idiomas:
Otros manuales de Lector de código de barras de Motorola
Motorola
Motorola Symbol DS6608 Manual de instalación y operación
Motorola
Motorola Symbol LS4278 Manual de usuario
Motorola
Motorola SYMBOL LS7708 Manual de instalación y operación
Motorola
Motorola LI4278 Manual de usuario
Motorola
Motorola LI4278 Manual de usuario
Motorola
Motorola Symbol DS6708 Manual de usuario
Motorola
Motorola LI4278 Manual de instalación y operación
Motorola
Motorola SYMBOL LS7708 Manual de usuario
Motorola
Motorola Symbol Manual de usuario
Motorola
Motorola Symbol DS6878 Manual de usuario
Motorola
Motorola WT41N0 Manual de usuario
Motorola
Motorola MC9190-NI Manual de usuario
Motorola
Motorola CA50 Manual de usuario
Motorola
Motorola MC17 Manual de usuario
Motorola
Motorola Symbol DS3407 Manual de usuario
Motorola
Motorola Symbol DS9808 Manual de instalación y operación
Motorola
Motorola Symbol DS3408 Manual de instalación y operación
Motorola
Motorola Symbol MS4404 Guía de configuración rápida
Motorola
Motorola LS2208AP Manual de usuario
Motorola
Motorola LI2208 Manual de usuario
