Motorola solutions VT-100 Manual de usuario
VT-100
QUICKSTART GUIDE
QUICKSTART GUIDE | VT-100 2
TABLE OF CONTENTS
INTRODUCTION 3
HOW TO CHARGE YOUR VT-100 3
HOW TO USE YOUR VT-100 6
HOW TO POWER UP YOUR VT-100 6
IF YOUR VT-100 IS CONFIGURED TO LIVESTREAM 7
IF YOUR VT-100 IS NOT CONFIGURED TO LIVESTREAM 7
HOW TO STOP RECORDING 8
WEARING YOUR VT-100 9
VT-100 ROTATABLE LONG ALLIGATOR CLIP 10
VT-100 KLICK FAST STUD 11
VT-100 SPORTS CAMERA PILLAR 12
VT-100 EPAULETTE (SHOULDER) CLIP 13
LANYARDS 15
REGULATORY INFORMATION 16
QUICKSTART GUIDE | VT-100 3
INTRODUCTION
Thank you for choosing the VT-100 Body-worn camera. This simple guide will lead you through the set up and
use of your VT-100.
The VT-100 is designed to function on standby for up to three months. Therefore, it is necessary to fully charge
the device before first use.
Microphone
Attachment
Point for Clip
FRONT BACK
Slot for
Custom ID Card
Lens
LED
Press to Record
Button & LED
LED
Press to Record
Button & LED
Micro
USB Port
QUICKSTART GUIDE | VT-100 4
HOW TO CHARGE YOUR VT-100
To charge, you will need either a USB charging cable (AC-USB-MICROB-100) or the VT-100 variant of the
14-Port Dock (VT-100-DOCK14).
USB Charging Cable
(AC-USB-MICROB-100)
VT-100 14-Port Dock
(VT-100-DOCK14)
QUICKSTART GUIDE | VT-100 5
While connected to power, the LED on the right side of the device will flash green while charging, and will go a
solid green when fully charged.
If the VT-100 is configured to connect to Wi-Fi® while docking, the back-right LED will flash blue when searching
for a Wi-Fi connection, and will become a solid blue when a Wi-Fi connection is found.
If your VT-100 has not already been configured by your system administrator, please see the VideoManager
Admin Guide for details on how to configure your VT-100.
CHARGING
(Flashing Green)SEARCHING FOR WI-FI
(Flashing Blue)
CONNECTED TO WI-FI
(Solid Blue)
QUICKSTART GUIDE | VT-100 6
HOW TO USE YOUR VT-100
HOW TO POWER UP YOUR VT-100
The VT-100 starts recording (and live streaming, if it has been configured to do so), as soon as it is powered up.
To power up your device, press either of the two buttons on the back of the device. The device will vibrate
briefly, and recording will start.
POWERING UP YOUR VT-100
Press and hold either
of the power buttons
QUICKSTART GUIDE | VT-100 7
IF YOUR VT-100 IS CONFIGURED TO LIVESTREAM
The recording LED on the back-left of the device should shine solid red, as well as the LED on the front of the
device. This indicates that the device is recording. The LED on the back-right of the device should be flashing
blue - about once a second - indicating that it is looking for Wi-Fi to connect to.
A solid blue light on the back-right LED indicates that the VT-100 has connected to the Wi-Fi.
IF YOUR VT-100 IS NOT CONFIGURED TO LIVESTREAM
The recording LED on the back-left of the device should now be a solid red, as well as the LED on the front of
the device. This indicates that the device is recording.
SEARCHING FOR WI-FI
(Flashing Blue)
CONNECTED TO WI-FI
(Solid Blue)
RECORDING
(Solid Red)
RECORDING
(Solid Red)
QUICKSTART GUIDE | VT-100 8
HOW TO STOP RECORDING
To stop recording, press and hold either of the buttons on the back of your device for one second.
The LED on the front of the device will switch o. If your VT-100 is configured to livestream, the back-right
LED will remain a solid blue, indicating that the device is still connected to the Wi-Fi, but no footage is being
recorded. After 10 more seconds, the camera will automatically switch o.
Once recording has stopped, the VT-100 will always automatically power down after ten seconds of inactivity in
order to preserve battery life.
POWERING DOWN
YOUR VT-100
Press and hold either
of the power buttons
STOPPED
RECORDING
(No LED)
STOPPED
RECORDING
(No LED)
CONNECTED TO WI-FI
(Solid Blue)
This light will go out
after 10 seconds
QUICKSTART GUIDE | VT-100 9
WEARING YOUR VT-100
The VT-100 can be attached to most uniforms and items of clothing using one of the robust clips which can be
purchased from Motorola Solutions (see following pages for options available).
These clips are rotatable - however, the camera should always remain upright when capturing footage.
QUICKSTART GUIDE | VT-100 10
VT-100 ROTATABLE LONG ALLIGATOR CLIP
To attach a Rotatable Long Alligator clip (VT-100-FIX-ALIG) to your VT-100, slide the attachment into the
mounting rail on the back of your device until a firm click is heard and the attachment point is held firmly in
place.
To detach the clip clip from your VT-100, pull the lip of the attachment plate away from the body of your VT-100
and firmly pull the attachment out of the rails.
Slide rotatable
attachment down
Tabla de contenidos
Otros manuales de Cámara digital de Motorola solutions
Motorola solutions
Motorola solutions L6Q Manual de usuario
Motorola solutions
Motorola solutions edesix VIDEOBADGE VB-400 Manual de usuario
Motorola solutions
Motorola solutions edesix VIDEOBADGE VB-400 Manual de usuario
Motorola solutions
Motorola solutions edesix VIDEOBADGE VB-400 Manual de usuario
Motorola solutions
Motorola solutions Avigilon 8.0C-H5A-FE-DO1 Manual de usuario
Motorola solutions
Motorola solutions L5Q Manual del operador
Motorola solutions
Motorola solutions V300 Manual de usuario
Motorola solutions
Motorola solutions PELCO IDL302-FXI Manual de usuario
Motorola solutions
Motorola solutions V700 Manual de usuario
Motorola solutions
Motorola solutions PELCO Sarix Multi Pro Manual de usuario
