Morso SQUIRREL 551 Manual de usuario

Squirrel - Gas Stoves

Model No. 551 - With Open Flue

Model No. 552 - With balanced Flue

OWNER’S GUIDE

THESE APPLIANCES ARE FOR USE WITH NATURAL GAS (G20)

OPEN FLUE STOVE MODEL 551 IS FOR USE WITH PROPANE GAS (G31) WHEN CON-

VERTED USING KIT NO. 0555111.

BALANCED FLUE STOVE MODEL 552 IS FOR USE WITH PROPANE GAS (G31) WHEN

CONVERTED USING KIT NO. 0555211.

THESE APPLIANCES ARE SUITABLE ONLY FOR INSTALLATION IN THE UNITED KING-

DOM (GB) AND THE REPUBLIC OF IRELAND (IE).

We trust that these instructions give sufﬁcient details to enable this appli-

ance to be installed and maintained satisfactorily. However, if further infor-

mation is required, our Technical Helpline will be pleased to help.

Telephone 01788 554410 (National call rates apply in the United Kingdom).

This guide is intended to help you care for your gas stove. Please read thoroughly before

using your gas stove and keep for future reference.

Manufactured by Morsø Jernstøberi A/S . DK-7900 Nykøbing Mors

E-Mail: [email protected] · Website: www.morsoe.com

Distributed by Morsø UK, Unit 5, io Center, Valley Drive, Swift Walley,

Rugby, Warks, CV21 1TW - www.morsouk.com

INSTALLER: Please leave this guide with the owner

C u s t o m e r C a r e

Thank you for choosing morsø.

All morsø appliances are designed to meet the most stringent quality, per-

formance and safety requirements to provide our customers with many years

trouble-free service.

Your owner guide aims to improve your understanding and appreciation of

your gas ﬁre by providing simple and informative instructions to ensure that

you beneﬁt from the excellent performance and features it has to offer.

LIST OF CONTENTS

Heading Page

SAFETY 3

OPERATING YOUR STOVE 6

The Flame Sensing & Flue Blockage Safety System 6

To Light The Pilot 6

To Light the Main Burner 6

To Turn Off the Main Burner Only 7

To Turn Off the Main Burner and Pilot 7

CLEANING YOUR STOVE 8

Cast Iron Surfaces 8

Opening the Door 8

The Glass Window 8

FITTING THE CERAMIC FUEL EFFECT AND

BURNER COMPARTMENT WALLS 9

MAINTENANCE AND SERVICING 12

SAFETY

IF YOU SMELL GAS

DON’T SMOKE

EXTINGUISH ALL NAKED FLAMES

DON’T TURN ELECTRICAL SWITCHES ON OR OFF

TURN OFF THE GAS SUPPLY AT THE METER

OPEN DOORS AND WINDOWS TO GET RID OF THE GAS

IMMEDIATELY CALL THE GAS EMERGENCY SERVICE - SEE YOUR

LOCAL TELEPHONE DIRECTORY

Do have the gas stove installed by a competent person. In the United Kingdom,

installation must be in accordance with the latest edition of the Gas Safety (in-

stallation & use) Regulations. In the Republic of Ireland, installation must be in

accordance with all national and local regulations in force.

Do have the chimney swept prior to installation if it was previously used for

solid fuel.

Do have the gas stove installed in accordance with the installation instructions.

On no account must the stove stand on carpets or other combustible materials.

The stove must stand on a non-combustible hearth surface. The hearth material

must be at least 400mm wide x 420mm deep x 12mm thick.

Do provide the minimum clearances shown in ﬁgure 1.

Do ensure that the ﬂue terminal on the outside wall (Balanced ﬂue model 552)

is kept free from all obstructions and blockages.

Do always use a ﬁreguard complying with BS 8423 for the protection of young

children, the elderly or inﬁrm.The cast iron top, front, rear and sides of this stove

are considered to be working surfaces and so will become very hot when in use.

Always take care when using this appliance. Such a guard is also recommended

for the protection of pet animals.

Do wait three minutes before attempting to relight if the gas stove is switched

off or the ﬂames are extinguished for any reason.(Your gas stove is ﬁtted with a

safety device that will automatically shut off the gas supply to the gas stove, if

for any reason , the ﬂame goes out)

Do get advice about the suitability of any wall covering near your gas stove.

Soft wall coverings (e.g. embossed vinyl, etc.) which have a raised pattern are

easily affected by heat. They may, therefore, scorch or become discoloured

when close to a heating appliance. Please bear this in mind whenever you are

considering redecorating.

Don’t hang clothing, towels or any other fabrics over the gas stove.

Don’t put more loose ceramic coals on the gas stove than the number given

in this guide or use any ceramic coals other than those authorised for this gas

stove. Incorrect combustion could result.

Don’t put paper or other materials into your gas stove.

Don’t use the gas stove with damaged base ceramics.

Don’t place any combustible material (rugs, carpet, plastic tiles, etc.) on the

hearth

Don’t attempt to clean or service the gas stove until it has been switched off

and allowed to cool completely.

Don’t use this stove with the door open or with the glass panel damaged or

removed. The door should always be secured with the locking screw (See

“Cleaning your stove”). If the window is damaged or will not close securely

the ﬁre must be turned off and not used until the window is changed or cor-

rected by a competent service engineer.

Don’t leave the stove on if the house is left unoccupied for a long period. We

recommend that the stove is turned fully off.

MODEL 551

MODEL 552

Figure 1

OPERATING YOUR STOVE

PLEASE NOTE

When operating your stove for the ﬁrst time, some vapours may be given

off which may cause a slight odour and could possibly set off any smoke

alarms in the immediate vicinity. These vapours are quite normal with

new appliances. They are totally harmless and will disappear after a few

hours use.

This ﬁre is supplied with ceramic “coals” to simulate a real coal ﬁre. After some

use, the ﬁrebox walls and coals may change colour. This is quite normal.

The Flame Sensing & Flue Blockage Safety System.

For your safety, this appliance is ﬁtted with a ﬂue blockage safety device that

will shut down the appliance in the event of abnormal ﬂue conditions.

This device is NOT a substitute for an independently mounted Carbon

Monoxide detector.

The device will also automatically shut off the gas supply to the ﬁre if the

pilot ﬂame goes out for any reason. If the device starts to shut off the gas

frequently, get expert advice.

The system incorporates a probe that senses that the heat from the pilot ﬂame

is correct. If this probe is cool, the device will prevent any gas ﬂow unless the

control knob is kept depressed at the PILOT/IGN position. If, for any reason,

the ﬂames go out when the ﬁre is hot or if the ﬁre is turned off when hot,

always wait at least three minutes before attempting to relight.

Always make sure that the window is securely closed before lighting.

To Light The Pilot

•Push in the right control knob (the pilot lighting knob) and, while keeping

it depressed, turn anticlockwise through the ignition position marked

and up to the pilot position marked. The spark should light the pilot. The

pilot ﬂame can be seen by looking through the gap between the coals

near the front left corner of the ﬁre bed – See ﬁgure3.

• When the pilot has lit, keep the right hand control knob depressed for a

few seconds to prevent the ﬂame supervision device from shutting off

the gas supply while its probe warms up, as explained above, then re

lease it.

To light the Main Burner

• Partially depress the right control knob and turn to the main burner position

marked . The main burner should now light.

• The left-hand knob is for burner ﬂame adjustment. Turning it

anticlockwise should gradually increase the ﬂame height and heat output.

Turning clockwise reduces the ﬂame height and heat output.

• The burner ﬂame conteol does not have to be re-set every time the ﬁre is lit.

Once set, it can be left at that position allowing you to use the right hand

control only to ignite the burner at the set ﬂame height.

To Turn Off the Main Burner Only

• Turn the right hand control knob to the pilot position marked .

To Turn Off the Main Burner and Pilot

• Turn the right hand control knob to the pilot position marked .

Push the knob in at this position and turn to the off position marked •.

Figure 2 Figure 3

• If the pilot does not remain alight turn the knob back to the off position

marked •. Wait a few seconds and repeat the lighting sequence.

CLEANING YOUR STOVE

Turn the stove off and allow it to cool before attempting any cleaning. Note

that it will retain heat for some time after it has been turned off.

Cast Iron Surfaces

Regular dusting with a dry cloth is all that should normally be necessary.

Any light stains should be removed with a damp cloth. Make sure that the

stove surfaces are completely dry before lighting.

If the paint needs retouching, allow the stove to cool completely. Brush any

areas needing attention with a wire brush (Not enamelled surfaces). Clean

off any loose matter. Touch up with MORSØ high temperature stove paint.

Apply the paint sparingly. Two light coats are better than one thick coat.

Figure 4

Opening the Door

The window is secured with a locking screw. Remove the screw using the

special key supplied with the stove. See ﬁgure 4. Always secure the window

with the locking screw to prevent inadvertent opening and consequent

injury or damage while the stove is in use.

The Glass Window

Any stains on the glass can be removed with a non-abrasive cleaner such as a

ceramic hob cleaner. Never use abrasive cleaners. Clean the window carefully

in accordance with the instructions supplied with the cleaner.

FITTING THE CERAMIC FUEL EFFECT

AND

BURNER COMPARTMENT WALLS

Ceramic fuel effect and Burner compartment Walls

• This product uses fuel effect pieces and burner compartment rear wall

containing Refractory Ceramic Fibres (RCF), which are man-made vitreous

silicate ﬁbres. Excessive exposure to this material may cause irritation to

eyes, skin and respiratory tract. Consequently, it is important to take care

when handling these articles to ensure that the release of dust is kept to a

minimum.

• Light coatings of soot will usually be burnt off during the normal operation

of the ﬁre.

• Should any soot accumulation become excessive, the fuel effect pieces

and walls should be removed from the ﬁre for cleaning.

• Cleaning should be carried out in a well ventilated area or in the open air by

gently brushing with the pieces held away from your face so that you avoid

inhaling the dust.

• We suggest that you remove the coals in the reverse order to that shown

in this section of the guide. When removing the fuel effect and burner com-

partment walls it is important that the front grate is removed before the fuel

effect pieces. To do this hold the front grate ﬁrmly and lift.

1. Place the rear ceramic wall against the back of the ﬁrebox.

2. The rear ceramic wall must be located onto the ledges at the back of the

rear base ceramic (See ﬁgure 5). To achieve this, hold the rear ceramic wall

against the rear of the ﬁrebox at its uppermost position. Whilst holding the

rear ceramic wall in this position locate the rear ceramic base coal into

position (See ﬁgure 5). The rear wall can now be released. Ensure that the

rear ceramic wall sits on the ledge at the back of the rear base coal.

Figure 5

Figure 7

Figure 6

3. Fit the left hand side wall against the left hand side of the ﬁrebox. Locate

the bottom of the side wall into the channel along the bottom of the ﬁrebox

(See ﬁgure 6). Supplied with the stove are two ceramic retaining brackets.

One for each side of the ﬁrebox. Hold the ceramic side wall against the

steel ﬁrebox plate and slide the long leg of a retaining bracket behind the

steel ﬁrebox plate. Push down to hold the ceramic side wall in place.

4. Fit the right hand side wall against the right hand side of the ﬁrebox. Locate

the bottom of the side wall into the channel along the bottom of the ﬁrebox.

Hold the ceramic side wall against the steel ﬁrebox plate and slide the

long leg of a retaining bracket behind the steel ﬁrebox plate. Push down

to hold the ceramic side wall in place.

5. On the front of the burner there is a bracket for supporting the front cera-

mic base. At the rear of the front ceramic base is a recess. Fit the front

ceramic base piece locating the recess onto the forward projecting part

of the burner bracket (See ﬁgure 7).

Otros manuales para SQUIRREL 551

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cocina de Morso

Morso

Morso 2B Standard Manual de usuario

Morso

Morso 8140 Manual de usuario

Morso

Morso 7600 series Manual de usuario

Morso

Morso 3610 Manual de lista de piezas

Morso

Morso 3600 Series Manual de usuario

Morso

Morso 3600 Series Manual de usuario

Morso

Morso P31 Manual de usuario

Morso

Morso S10-70 Manual de usuario

Morso

Morso 1400 Manual de usuario

Morso

Morso S50 Manual de usuario

Morso

Morso S11 Series Manual de usuario

Morso

Morso S50-40 Manual de usuario

Morso

Morso 6100 series Manual de usuario

Morso

Morso 7110 Manual de usuario

Morso

Morso 553 Manual de usuario

Morso

Morso 1126 Manual de usuario

Morso

Morso 3400 Series Manual de usuario

Morso

Morso 3440 Manual de usuario

Morso

Morso 1412 Manual de usuario

Morso

Morso 1430 Cleanheat Squirrel Guía de inicio rápido

Morso

Morso 1410 Manual de usuario

Morso

Morso 3100 Series Manual de usuario

Morso

Morso 2B Classic Manual de usuario

Morso

Morso 6600 Manual de usuario

Manuales populares de Cocina de otras marcas

Arada

Arada Cassette Stove Manual de usuario

Parmco

Parmco FS 600 Manual de usuario

MCZ

MCZ SUITE AIR 10 M2 Manual de usuario

HearthStone

HearthStone Stowe DV 8321 Guía de solución de problemas

Cattara

Cattara FAMILY Manual de usuario

Stanley

Stanley Argon F500 OVAL Manual de usuario

Avalon

Avalon B-VENT Manual de usuario

Nordpeis

Nordpeis Vega Manual de usuario

Exquisit

Exquisit EKC601-5 Manual de operación

Stanley

Stanley Oisin Oil MK II Manual del propietario

Thermocet

Thermocet Brookfield S/CC Manual de usuario

HASE

HASE delhi Manual de usuario

Vermont Castings

Vermont Castings Intrepid 2 Manual de usuario

Italiana Camini

Italiana Camini CLASSICA Guía de inicio rápido

Avalon

Avalon Vashon Avanti DVS FS Manual de usuario

Spartherm

Spartherm ambiente a1 Manual de usuario

Dimplex

Dimplex MCFSTV12AU Manual de usuario

Warmlite

Warmlite WL46040 Manual de usuario