Morso 1710 Insert Manual de usuario

MORSØ JERNSTØBERI A/S . DK-7900 NYKØBING MORS

E-Mail: stoves@morsoe.com · Website: www.morsoe.com

Distributed by: MORSO US LLC

1011 Highway 52 West - Portland TN - 37148 - USA

Installation and Operating Instructions

1710 Insert

For use in North America

Read this entire manual before you install and use your new room heater. If this room

heater is not properly installed, a house ﬁre may result. To reduce the risk of ﬁre, follow

the installation instructions. Failure to follow instructions may result in property damage,

bodily injury, or even death.

Contact local building ofﬁcials about restrictions and installation/inspection-requirements

in your area.

Save these instructions

We congratulate you on your choice of a Morsø stove. Morsø has

been producing some of the world’s best stoves since 1853. If you

follow this installation- and operating instruction carefully, we can

assure you many years of warmth and pleasure.

Optional Accessories

A wide range of accessories (such as handling gloves, ﬁreside tools, glass cleaner and heatproof

paint) are available for use with your Morsø stove. They help with day-to-day running and

maintenance. Contact your Morsø dealer for more information.

The Morsø 1710 Insert meets the U.S. Environmental Protection Agency’s emission limits for

wood heaters sold on or after July 1, 1990

The Morsø 1710 Insert have been tested by OMNI-Test Laboratories, Inc. The test standards

are ANSI/UL-1482 for the United States and ULC S627 for Canada.

The stove is listed for burning wood only. Do not burn other fuels.

Under speciﬁc test conditions this heater has been shown to deliver heat at rates ranging from

12,000 to 39,000 Btu/hr.

CONTENTS:

1.0 Installation of your Morsø stove

1.1 Checking loose parts in the stove 5

1.2 The chimney / ﬂue system 7

1.3 Flue Connection 8

1.4 Connection to existing chimney 8

1.5 Positioning the stove 10

2.0 Operation

2.1 Before you start ﬁring 12

2.2 Lighting and loading intervals 13

3.0 Maintenance 16

3.1 Exterior maintenance 16

3.2 Internal maintenance 16

3.3 Cleaning the Stove and the Flue 18

3.4 Leaving the stove for extended periods 20

3.5 Parts diagram 21

3.6 Parts list 22

Installation requirements vary in different districts, and the local building ofﬁcials have the ﬁnal

authorization to approve your installation. You should discuss the installation with them before

beginning. Please ask your dealer for further information.

1.0 Installation of your Morsø stove

Installation of woodburning stoves must be safe and legal.

If your Morsø stove is not installed correctly, it may cause a house ﬁre. To reduce

the risk of ﬁre, the installation instructions must be followed carefully. Contact the

local building ofﬁcials about restrictions and installation inspection in your area.

Before you start installing your stove, make sure that:

- The stove and chimney connection are placed far enough from combustible materials to

meet all clearance requirements.

- The ﬂoor protection must be adequate and must be made correctly according to the re-

quirements.

All neccessary approvals are needed from the local building ofﬁcials.

The data plate, which is located on the back of the stove, provides information regarding safety

testing information, name of certiﬁed testing laboratory, and installation requirements.

There are numerous ways of building a

chimney. We will just describe a couple of

mountings of the insert.

The MORSØ 1710 insert can be installed as

described below. The 1710 can also be used

as a build-in stove with masonry/chimney

construckted for the size of the outer steel box,

as shown on the front page of this manual

1. Remove the existing damper, if there is one.

(Fig. 1)

2. It is easier to make adjustments to the

mansonry surrounding the insert, when the

heavy cast iron insert is not connected to

the steel box. (see item a-f page 5). Use the

steel box as a template for the mansonry

adjustments

3. It is important to leave a gap of few

millimeters between the steel box and the

mansonry because of increasing size when

warmed up.

If possible leave 25-30 mm. and ﬁll up the

gap with heat resistant insulation material.

As shown in ﬁgure A, the steel box must

project 10 mm. from the mansonry. The steel

box should be adjusted by support

Dimensions in milimeters

b. Lift the lower bafﬂeplate a bit and hold

in that position. Carefully lift and remove

the two side bricks.

c. Remove the ﬁrebrick from the back-

wall

d. Remove the lower bafﬂeplate

e. The upper bafﬂeplate is removed from

the brackets and lifted out of the ﬁre-

champer

f. Unscrew the 2 bolts, which is mounted

to the stainless steel bafﬂe Dismantle the

ﬂue collar. Pull out the cast iron insert

from the steel box

Dismantling the steel-box

a. Lift and remove the front grate.

Do not connect to any air distribution duct or system.

Important: If the installation instructions are not followed carefully, it may cause

dangerous situations like chimney - and house ﬁres. Follow the instructions

carefully and do not deviate from them as it may cause injuries to people or

property.

material until the bottom becomes horizontal. It

is an advantage to fasten the box by two screws

drilled through the bottom 2-3 cm. from the

corners of the back.

Figure 2:

The connection between the insert and the

chimney is made by a dia. 155 mm. ﬂuecollar,

which is fasten in the smoke pipe socket by the

enclosed selfcutting screws (spoil in the boring

dia. 3 mm.) and tightened by the enclosed

ﬁreproof seal. Tighten between smoke pipe and

chimney with ﬁreproof clay. It is important to use

a pipe bush and ﬁreproof seal in order to avoid

cracks in the ﬁreproof clay, caused by thermal

exspansion of the smoke pipe. If no access door

exists beforehand, as shown in ﬁgure 2, it may be

an advantage to mount one. Thus the mounting

of the smoke pipe is facilitated and some times

it is a demand from the building authorities. In

order to obtain a correct execution of the above,

it might be an advantage to consult the local

chimneysweep or the building authorities.

4. Lift and push the insert in its place in the steel

box. Assemble the internal of the stove and ﬂue

collar. (see item a-f page 5, reverse order)

5. The initial ﬁre should be small in order to properly

cure the cast iron parts. Allow the stove to warm

up before creating a very hot ﬁre. Never let the

stove become superheated. Superheating may

damage the casting, ﬁre bricks and the Senotherm

painted ﬁnish. Superheating is when any part of

the stove, grates or stove pipe assumes a red

glow

Dimensions in milimeters

1.2 The chimney / ﬂue system

Note that the ﬂue system must be independently secured and must not rely on the stove for

support.

The stove must not be connected to a chimney ﬂue serving any other appliance.

(Several ﬂues may run up a single chimney stack; use one ﬂueway per appliance).

Use a residential type masonry or listed type HT factory-built chimney.

High Temperature (H.T.) Chimney Standard UL-103-1985 (2100º F.) for the USA, and

High Temperature (650ºC) Standard ULC S-629 for Canada.

The internal dimensions of the chimney connector and chimney must not be less than 6 inches

diameter (or equivalent cross section), and should not be signiﬁcantly larger than this. Too

large a section will tend to allow the ﬂue gases to cool excessively, causing sluggishness or

unpredictability in the stove’s performance.

We recommend the length of the chimney system should be at least 16 feet (not required) above

the stove in normal domestic situations, measured from the ﬂue collar to the top of the chimney.

Local conditions like for example - roof constructions, large trees nearby and high altitude, may

inﬂuence the chimney draft and height. Therefore, contact the local professional chimney sweep or

your Morsø dealer.

Typical Factory-Built or Masonry Chimney Installations

Double-wall connectors must be tested and listed for use with solid-fuel burning appliances.

Single-wall connectors should be made of 24 gauge or heavier gauge steel. Do not use

galvanized connector; it cannot withstand the high-temperatures that smoke and exhaust

gases can reach, and may release toxic fumes under high heat. The connector must be 6 inches

(150mm) in diameter.

If possible, do not pass the chimney connector through a combustible wall or ceiling.

If passage through a combustible wall is unavoidable, refer to the sections on Wall

Pass- Throughs. Do not pass the connector through an attic, a closet or similar

concealed space when installing the chimney connectors.

It is important to keep the ﬂue gases moving smoothly in the right direction. Do not vent into a

large void at this location; rather form one continuous section all the way up. Use mild bends

(e.g. 45º vs. 90º) rather than sharp angles where a change of direction is required. All parts of

the venting must be accessible for cleaning purposes.

In horizontal runs of chimney, maintain a distance of 18 inches from the ceiling. Keep it as

short and direct as possible, with no more than two 90 degree turns. Slope horizontal runs of

connector upward 1/4 inch per foot (20 mm per metre) going from the stove toward the chimney.

The recommended maximum length of a horizontal run is 3 feet (1 metre), and the total length

should be no longer than 8 feet (2.5 metres).

Information on assembling and installing connectors is provided by the manufacturer’s

instructions exactly as you assemble the connector and attach it to the stove and chimney.

Be sure the installed stove and chimney connector are correct distances from near by

combustible materials. See the clearance paragraph page 8.

1.3 Flue Connection

The stove is supplied from the factory with a ﬂue collar ﬁtted to the top plate.

The ﬂue collar is from the factory prepared for ﬁtting the enlosed 6 inche adapter.

Use a 24 MSG black or blue chimney connector or listed double wall chimney connector. Refer

to local codes and the chimney manufacturer’s instructions for precautions required for passing

a chimney through a combustible wall or ceiling. Remember to secure the chimney connector

with a minimum of three screws to the product and to each adjoining section.

Position the stove and connect to the ﬂue system.

Wear gloves and protective eyewear when drilling, cutting or joining sections of

chimneyconnector.

1.4 Connection to the existing chimney

A Chimney connector is the double-wall or single-wall pipe that connects the stove to the

chimney. The chimney itself is the masonry or prefabricated structure that encloses the ﬂue.

Chimney connectors are used only to connect the stove to the chimney.

1.5 Positioning the stove

IN CASE THE MORSØ 1710 INSERT, AS EXSPECTED, IS NOT USED AS

A INSERT IN AN NON-COMBUSTIBLE CHIMNEY FOLLOWING RULES

APPLY

Distance to walls and lintel

When the stove is positioned near combustible materials, observe all current local and national

building regulations with regards to clearances. Whatever regulations apply to your area, do

not in any case install the stove within 8 inches of combustible materials around the sides or

16 inches above the top of the stove (ﬁreplace installations require greater clearances above

the stove - see below in the clearance chart). These distances may need to be increased if the

materials are sensitive to heat. Note also that wall paper and other decorative materials may

become detached with the effects of heat and care should be taken to ensure that they do not

fall towards the stove in such an event.

When the stove is positioned near non-combustible materials, a gap of 4 inches or more is

recommended for cleaning purposes and to ensure that heat circulates around the stove and

out into the room.

CLEARANCE TO COMBUSTIBLE SURFACES REQUIREMENTS:

The ﬂoor in front of the ﬁreplace requires thermal projection of 1 inch (25 mm) thick mune-

ral ﬁber millboard with a value ofk=84 BYU/IN FT² HR °F when the ﬂoor is 3 inches or more

below the bottom opening of the ﬁreplace extending out 16 inches (406 mm).

INSTALLLATION A B C D E* F

UNITED STATES 15” 29” 22” 8” 18” 8”

CANADA 381mm 838mm 635mm 200mm 455mm 200mm

Otros manuales para 1710 Insert

Tabla de contenidos

Otros manuales de Cocina de Morso

Morso

Morso P50 Manual de usuario

Morso

Morso 6191 Manual de usuario

Morso

Morso 7840 Manual de usuario

Morso

Morso S81-90 Manual de usuario

Morso

Morso 6100 series Manual de usuario

Morso

Morso P31 Manual de usuario

Morso

Morso 2B Classic Manual de usuario

Morso

Morso 553 Manual de usuario

Morso

Morso 7800 Series Manual de usuario

Morso

Morso 3100 Series Manual de usuario

Morso

Morso 3440 Manual de usuario

Morso

Morso S11-40 Manual de usuario

Morso

Morso SQUIRREL 551 Manual de usuario

Morso

Morso 3100 Series Manual de usuario

Morso

Morso S12 series Manual de usuario

Morso

Morso 5400 Manual de usuario

Morso

Morso 3450 Manual de usuario

Morso

Morso SQUIRREL 551 Manual de usuario

Morso

Morso 6600 Manual de usuario

Morso

Morso 2B Classic Manual de usuario

Morso

Morso 3610 Manual de lista de piezas

Morso

Morso S11 Series Manual de usuario

Morso

Morso 1410 Manual de usuario

Morso

Morso 1410 Manual de usuario

Manuales populares de Cocina de otras marcas

Arada

Arada Cassette Stove Manual de usuario

Parmco

Parmco FS 600 Manual de usuario

MCZ

MCZ SUITE AIR 10 M2 Manual de usuario

HearthStone

HearthStone Stowe DV 8321 Guía de solución de problemas

Cattara

Cattara FAMILY Manual de usuario

Stanley

Stanley Argon F500 OVAL Manual de usuario

Avalon

Avalon B-VENT Manual de usuario

Nordpeis

Nordpeis Vega Manual de usuario

Exquisit

Exquisit EKC601-5 Manual de operación

Stanley

Stanley Oisin Oil MK II Manual del propietario

Thermocet

Thermocet Brookfield S/CC Manual de usuario

HASE

HASE delhi Manual de usuario

Vermont Castings

Vermont Castings Intrepid 2 Manual de usuario

Italiana Camini

Italiana Camini CLASSICA Guía de inicio rápido

Avalon

Avalon Vashon Avanti DVS FS Manual de usuario

Spartherm

Spartherm ambiente a1 Manual de usuario

Dimplex

Dimplex MCFSTV12AU Manual de usuario

Warmlite

Warmlite WL46040 Manual de usuario