Monoprice 10489 Manual de usuario
10489 Manual
MONOPRICE
PID 10489
27" IPS-G Pro LED Monitor
User's Manual
CONTENTS
1
SAFETY GUIDELINES
FEATURES
PACKAGE CONTENTS
CONNECTIONS & CONTROLS
MONITOR STAND & BASE
VIEW ANGLE ADJUSTMENT
INSTALLATION
POWER
INPUT SELECTION
ON-SCREEN DISPLAY (OSD) MENU
BASIC MENU OPERATION
TROUBLESHOOTING
SPECIFICATIONS
PRESET DISPLAY MODES
----------------------------------------------------------------- 2
-------------------------------------------------------------------------------- 3
---------------------------------------------------------------- 3
----------------------------------------------------- 4
------------------------------------------------------------ 5
-------------------------------------------------------- 7
--------------------------------------------------------------------------- 7
------------------------------------------------------------------------------------- 8
--------------------------------------------------------------------- 8
--------------------------------------------- 8
----------------------------------------------------------- 9
----------------------------------------------------------------- 16
----------------------------------------------------------------------- 18
----------------------------------------------------------- 19
To avoid personal injury or damage to your equipment, please adhere to the
following safety guidelines:
1. Do not place the monitor on an unstable surface where it could fall and
cause personal injury or damage to the monitor or other equipment.
2. Do not expose the monitor to water or moisture of any kind. Do not place
objects filled with moisture such that they could tip over and spill onto the
monitor.
3. If the monitor is exposed to moisture, immediately unplug the power source
and allow it to completely dry out before reapplying power.
4. Do not block the ventilation holes on the monitor. Do not place the monitor
in an enclosed space where it cannot get adequate ventilation or cooling.
5. Do not place the monitor near a heat source, such as a fireplace, radiator,
heater vent, etc.
6. The power supply for this monitor uses a NEMA 5-15 grounded plug.
Ensure that your power source is properly grounded. Do not use a "cheater"
plug to bypass the ground pin.
7. The monitor can be powered by a wide voltage range, from 100 to 240 V
AC at 50 or 60 Hz, with an AC current at least 3.75A. Ensure that your power
source supplies voltage within this operating range. If your power source is
not within this operating range, please consult your local power company.
8. If the monitor will be unused for a long period of time, turn it off and unplug
it from the power source. This will help prevent damage in the event of a
lightning strike or excessive power surge.
9. Do not attempt to open the case or service the monitor yourself.
10. Clean only with a soft, dry cloth. Do not use solvents or chemical cleaners
on the screen or casing.
11. Do not leave a single image on the display for an extended length of time.
Doing so could cause burn-in of the image, that is visible on the screen mask.
It is recommended to use a variable desktop background and to use a screen
saver to prevent burn-in. Alternatively, ensure that the monitor is powered off
for at least 2 hours out of every 12.
SAFETY GUIDELINES
2
27" IPS monitor with LED backlighting
16:9 aspect ratio
2560 x 1440 @ 60Hz maximum resolution
Includes DisplayPort, VGA, HDMI, and Dual Link DVI-D input options
Angle adjustable stand +20 ~ -5 degrees
Built-in stereo speakers with 2 watt/channel amplifier
FEATURES
1x 27" IPS LED monitor
1x Stand base
1x AC power adapter
1x AC power cord
1x 3.5mm audio cable
1x Dual Link DVI-D cable
1x User's manual
PACKAGE CONTENTS
3
1 DP DisplayPort connector
CONNECTIONS & CONTROLS
2 VGA VGA port
3 DVI Dual Link DVI-D port
4 HDMI HDMI port
5 AUDIO 3.5mm stereo TRS audio jack
6 DC IN
AUTO
1234567
VOL+ VOL- UP DOWN MENU
DC power connector
1 AUTO
7 Power ON/OFF
2 VOL+ Increases the volume level
Moves the selection to the right in the menus
Exits the main menu/ Auto adjusts the image
Displays the source list
3 VOL- Decreases the volume level
Moves the selection to the left in the menus
4 UP Moves the selection up in the menus
Selectable Hotkey action
5 DOWN Moves the selection down in the menus
Selectable Hotkey action
6
MENU Displays the main menu
Edit highlighted menu item
VGA connector
DP connector
DVI connector HDMI connector
Audio connector
DC IN
4
The monitor stand comes already attached to the back of the monitor. To
install the base, perform the following steps:
1. Place a blanket or towel on a flat surface (such as a table or the floor).
2. Place the monitor face down on the blanket or towel.
3. Swivel the stand up so that there is sufficient vertical space to install the
base.
4. Fit the base on the bottom of the stand and press it until it clicks into place.
To remove the base, perform the following steps:
1. Place a blanket or towel on a flat surface (such as a table or the floor).
2. Place the monitor face down on the blanket or towel.
3. Squeeze the two plastic clips on the bottom of the base and pull the base
off the stand.
MONITOR STAND & BASE
5
Note that the stand can be removed from the back of the monitor so that the
monitor can be attached to a desk or wall mount. To remove the stand,
perform the following steps:
1. Place a blanket or towel on a flat surface (such as a table or the floor).
2. Place the monitor face down on the blanket or towel.
3. Remove the four screws attaching the stand to the back of the monitor.
To attach the monitor to a desk or wall mount, please refer to the instructions
for the mount.
Note: The monitor uses a VESA mounting size of 100x100.
100mm
100mm
6
If you are using the stand and base that comes with the monitor, you can
adjust the vertical angle of the monitor from -5 degrees (down) to +20
degrees (up). To adjust the angle, grasp the top and bottom edges of the
display, taking care not to touch the glass on the front. You can use clean
gloves or soft, dry cloths to aid in grasping the display edge without touching
the screen.
VIEW ANGLE ADJUSTMENT
1. Install the base or attach the monitor to a desk or wall mount, as desired.
(See MONITOR STAND & BASE)
2. Using the included video signal cables, connect video source devices to
the appropriate ports on the back of the monitor. You can have a different
video source device for each input.
3. Plug the DC power connector into the DC IN port on the back of the
monitor.
4. Plug the AC cord into the AC adapter, then plug the other end into a power
outlet.
INSTALLATION
5° 20°
7
Press the power button to turn the monitor ON. The LED indicates the power
state:
Blue - Power is ON
Orange - Standby mode
Off - No power to monitor
POWER
1. Press the AUTO button to display the list of inputs.
2. Press the UP or DOWN buttons to move the red highlight to the desired
input.
3. Press the MENU button to switch to the highlighted input.
ON-SCREEN DISPLAY (OSD) MENU
The built-in OSD menu system allows you to adjust the various settings
options on the monitor.
INPUT SELECTION
8
Tabla de contenidos
Otros manuales de Monitor de Monoprice
Monoprice
Monoprice 31006 Manual de usuario
Monoprice
Monoprice 37924 Manual de usuario
Monoprice
Monoprice 33821 Manual de usuario
Monoprice
Monoprice 13809 Manual de usuario
Monoprice
Monoprice 33822 Manual de usuario
Monoprice
Monoprice Zero-G 31004 Manual de usuario
Monoprice
Monoprice 34712 Manual de usuario
Monoprice
Monoprice 13808 Manual de usuario
Monoprice
Monoprice 24659 Manual de usuario
Monoprice
Monoprice 38576 Manual de usuario
Monoprice
Monoprice 38577 Manual de usuario
Monoprice
Monoprice 34711 Manual de usuario
Monoprice
Monoprice 37923 Manual de usuario
Monoprice
Monoprice DARK MATTER 44710 Manual de usuario
Monoprice
Monoprice 34in CrystalPro Curved 1000R VA Panel Manual de usuario
Monoprice
Monoprice Dark Matter 40778 Manual de usuario
Monoprice
Monoprice 10509 Manual de usuario
Monoprice
Monoprice 31005 Manual de usuario
Monoprice
Monoprice 12520 Manual de usuario
Monoprice
Monoprice 6960 Manual de instrucciones
