Monark 915E Manual de usuario
MANUAL
P-7950-254, 0507
Exercise cycle
915E
2
3
CONTENTS
Assembly instructions ...................................................................................................... 4
Operation instructions................................................................................................... 7
Setting of work load............................................................................................................ 8
Calibration............................................................................................................................................ 10
Brake belt contact surface and brake belt................................... 11
Replacement of brake belt....................................................................................... 11
Chain .............................................................................................................................................................. 12
Crank bearing ................................................................................................................................. 13
Replacement of the freewheeling sprocket............................... 13
Replacement of sensor.................................................................................................... 14
Flywheel bearing........................................................................................................................ 14
Service............................................................................................................................................................ 15
Warranty ................................................................................................................................................... 15
General about exercise.................................................................................................... 16
Congratulations on your decision to purchase a product
manufactured by Monark in Sweden. Monark has been
the world´s leading manufacturer of high quality ergo-
meters and exercise cycles for more than 40 years.
4
ASSEMBLY INSTRUCTIONS
The parts shown below are not assembled.
Assembly instructions, see pages 5-6.
Electronic meter
Lever
Handlebar/Handlebar stem
Handwheel with tension screw
Saddle/Saddle post
Pressure washers
Bolts
Pedal, left hand
Pedal, right hand
Supporting tube,
front Supporting tube, back
Fig 1
5
Place the support for the tension axle/screw as far down
as it takes to push through the axle for the tension knob.
Place the pressure washer with the smaller part in di-
rection outwards inside the head tube.
Take the cable for the meter through the head tube.
Assemble the handlebar/stem and tighten carefully.
Note! Be careful when assembling the handlebar stem so
that the electric cable does not get pinched.
Turn the handlebar/stem in a comfortable position and
tighten carefully with the lever.
Screw in the tension screw into to the tension device.
Put together the connectors on the cable for the meter
and push the meter onto the fastening plate. See fig.2.
ASSEMBLY INSTRUCTIONS cont.
Electronic meter
Handlebar
Lever
Handlebar
stem
Handwheel with
tension screw
Support
Head tube
Pressure
washer
Bolt
Fig 2
Saddle clip
Saddle post bolt
Pressure
washer
Saddle post
Fig 3
Adjust the saddle/saddle post to desired height. Then
tighten with the saddle post bolt. See fig 3.
In order to change the inclination of the saddle, loosen
the saddle clip. See fig 3.
Note! Tighten firmly.
Joint contact
6
ASSEMBLY INSTRUCTIONS cont.
Tip the cycle forward and remove the transport block.
Assemble the back supporting tube with two bolts and
two nuts. See fig 4.
Note! Use the accompanying spanner.
Production number
Fig 4
Fig 5
Fig 6
Tip the cycle backwards. Assemble the front suppor-
ting tube with two nuts onto the two fixed bolts. See
fig 5.
Note! Use the accompanying spanner.
Plastic tape
Take off the brake belt and remove the plastic tape from
the flywheel.
Assemble the brake belt as before. See fig 6.
Note! It is very important that all of the plastic tape is
removed. Residue of the plastic tape may cause an uneven
operation.
Fig 7
Pedal, right hand
side, marked R
Pedal, left hand
side, marked L
The pedal marked R (right) to be assembled on the
right hand side of the cycle (the chain wheel side). The
pedal axle has a right hand thread and must be thread-
ed onto the crank clockwise. Tighten firmly. See fig 7.
The pedal marked L (left) to be assembled on the lefte
hand side of the cycle. The pedal axle has a lefte hand
thread and must be threaded onto the crank counter
clockwise. Tighten firmly. See fig 7.
7
Fig 9
OPERATION INSTRUCTIONS
Exercise cycle 915E
This testing cycle is provided with a brake system, which
power can be read in watts at two different speeds, 24
km/h (60 rpm) and 28 km/h (70 rpm). See fig 8.
This model is also equipped with an electronic meter
which – on one big display – at the same time shows:
PULSE (heart rate), SPEED (km/h), TIMER, CALO-
RIES and DISTANCE (km). See more under Fitness
Computer.
When pedalling the test person supplies the flywheel
with a certain kinetic energy. This kinetic energy is
braked by means of a brake belt which runs around
the bigger part of the brake surface of the flywheel.
The brake power is changed either by using another
pedalling speed or by increasing or decreasing the ten-
sion of the brake belt against the flywheel by means of
the tension handwheel. See fig 8.
The height of the saddle is adjusted so that, when you
sit comfortably with your foot exactly above the pedal
axle and with the pedal in its down position, your knee
is only slightly bent.
The adjustment of the handlebar should give a com-
fortable ride. When cycling for a long time, it may be
suitable some time during the exercise to change the
position of the handlebar.
Fitness computer / Electric meter
Specifikation
PULSE 50 - 199 bpm
PULSE-HI 50 - 199 bpm
PULSE-LOW 30 - (HI-10) bpm
SPEED 0 - 199 km/h
TIMER (up) 00:00 - 99:59 min:sek
TIMER (down) 99:00 - 0:00 min:sek
CALORIES (up) 0 - 999 kcal
CALORIES (down) 999 - 0 kcal
DISTANCE (up) 0.00 - 99.99 km
DISTANCE (down) 99.00 - 0.00 km
Power supply 1.5 V x 2 R6
Storage temperature -10
°
C - 60
°
C
Operation temperature 0
°
C - 50
°
C
Fig 8
Tension
handwheel
Keys and function
MODE key
Use ”MODE key to set mode and cycle through the
display windows as below:
PULSE HI – PULSE LOW – TIMER – CALORIES
– DISTANCE
SET key
Press ”SET” key to set desired value. If you hold/press
this key for two seconds or more, you can advance the
function value at a faster rate.
RESET key
A press on the key will clear the values separately for
TIME, DISTANCE, CALORIES (kcal) and HI/LOW
pulse limit individually.
8
OPERATION INSTRUCTIONS cont.
If you hold down the button for more than two se-
conds at normal display, all values except upper and
lower pulse limit will be set to zero at the same time.
PROGRAMMING EXERCISE TIME
Press ”Mode” key to advance to the time window, then
use ”SET” key to enter your desired time. Each press
of the SET key will advance time by one minute.
PROGRAMMING TARGET TRIP
Press ”MODE” key to advance to the distance win-
dow, then use ”SET” key to enter your desired target
trip distance. Each press of the SET will advance dis-
tance by 0.5 km.
PROGRAMMING CALORIES
Press ”MODE” key to advance to the calories window,
then use ”SET” key to enter your desired calories bur-
ned. Each press of the SET will advance calories by 10
Kcal.
PROGRAMMING HIGH AND LOW PULSE
RATE LIMIT
Press ”MODE” key to advance to the pulse window,
then use ”SET” key to enter your desired high and low
pulse rate/herat rate limit. Each press of the SET will
advance 5 bpm. If your heart rate is above the high
pulse limit you programmed, the computer will gene-
rate a beeping to warn you to stop exercise. In con-
trast, if your pulse rate is lower than your desired low
pulse rate limit, the buzzer will also beep to remind
you to continue your exercise.
PROGRAMMING TIMER
Use the MODE key to advance to the timer function.
Then use the SET key to adjust to desired time. Every
push on the SET key will increase the time by one
minute.
PROGRAMMING CALORIES
Use the MODE key to advance to the KCAL func-
tion. Then use the SET key to adjust to desired amount.
Every push on the key will increase the value by one
minute.
PROGRAMMING DISTANCE
Use the MODE key to advance to the DISTANCE
function. Then use the SET key to adjust to desired
distance. Every push on the key will increase the dis-
tance by one km.
NOTE:
When no key has been pressed for 5 seconds the dis-
play will return to normal. The computer starts auto-
matically when one of the keys is pressed or meter get
speed indication – is pedalled.
In normal display, please make sure the ❤-symbol ap-
pears on the display before measuring your pulse rate.
The ❤-symbol will automatically disappear to save po-
wer when no key has been pressed or no signal has
been received for 30 seconds or more. By pressing
”SET” or RESET” the symbol will turn on again.
9
SETTING OF WORK LOAD
If you intend to exercise with a work load of 50 watts
and a pedalling speed of 24 km/h (60 rpm), do as fol-
lows:
Check on the RPM-display of the meter that you have
achieved the correct pedalling speed.
After that the tension handwheel should be adjusted
so that 50 watts are shown on the scale for 24 km/h.
Power conversion table at other pedalling speeds
The conversion table below shows the conversion into
watts at other pedalling speeds than 24 and 28 km/h
respectively. The result is achieved according to the fol-
lowing example:
Chose as work load any of the watt numbers on the
scale for 24 km/h at the same time as you pedal with
this speed.
Let us imagine that you have chosen 120 watts as work
load. If you now increase the pedalling speed to 90
rpm the table should be read as follows:
Start from the line 24 km/h and continue to 120 watt
and further to the line for 90 rpm. You can then read
that the actual power is 180 watts. See the markings in
the table below.
50 watt
Tension
handwheel
Fig 10
Watts indicated
on the scale for
24 km/h
Actual speed
and actual
work load
RPM km/h WORK LOAD watt
40 16 20 40 60 80 100 120 140 160 180 200
50 20 25 50 75 100 125 150 175 200 225 250
60 24 30 60 90 120 150 180 210 240 270 300
70 28 35 70 105 140 175 210 245 280 315 350
80 32 40 80 120 160 200 240 280 320 265 400
90 36 45 90 135 180 225 270 315 360 405 450
100 40 50 100 150 200 250 300 350 400 450 500
110 44 55 110 165 220 275 330 385 440 495 550
120 48 60 120 180 240 300 360 420 480 540 600
10
CALIBRATION
Fig 12
Fig 11
Adjust the tension handwheel so that there is no ten-
sion in the brake belt.
Fasten a 4 kg weight (our part no 9000-211) around
the joint clamp. See fig 11.
When correctly set the weight – 4 kp – will be read on
the scale for watts – 60 rpm. See fig 12. Should there
be a deviation, dismantle the left cover. See page 12.
Adjust into the correct position by means of the adjus-
ting screw and locking nuts. See fig 11.
4 kp
Joint clamp
Adjusting screw
Locking nut
Tension
handwheel
Otros manuales para 915E
2
Tabla de contenidos
Otros manuales de Bicicleta estática de Monark
Monark
Monark Ergomedic 874 E Manual de usuario
Monark
Monark CARDIO COMFORT 837 E Manual de usuario
Monark
Monark 939 novo Manual de usuario
Monark
Monark Cardio Care 827 E Manual de usuario
Monark
Monark 828E Manual de usuario
Monark
Monark 839 E Manual de usuario
Monark
Monark 808 Manual de usuario
Monark
Monark 828E Manual de usuario
Monark
Monark Ergomedi 894 E Manual de usuario
Monark
Monark 828 novo mini Manual de usuario
Monark
Monark Ergomedic 874 E Manual de usuario
Monark
Monark RT2 Manual de usuario
Monark
Monark LT2 Manual de usuario
Monark
Monark 928 E Manual de usuario
Monark
Monark 928 E Manual de usuario
Monark
Monark LC7TT novo Manual de usuario
Monark
Monark 827E Manual de usuario
Monark
Monark LC6 novo Manual de usuario
Monark
Monark cardio care 827 x Manual de usuario
Monark
Monark LC4 Manual de usuario
Manuales populares de Bicicleta estática de otras marcas
American Fitness
American Fitness SPR-BK1072A Manual de usuario
Cateye
Cateye CS-1000 (CYCLO SIMULATOR) Manual de usuario
BH FITNESS
BH FITNESS H9158H Manual del operador
Body Sculpture
Body Sculpture BC-7220G Manual de usuario
Cateye
Cateye EC-2300 Manual de usuario
FYTTER
FYTTER RACER RC MSR Manual de usuario
