Mobeye PowerGuard CM2100 Manual de usuario

USER MANUAL

Mobeye®PowerGuard

CM2100

SW version 4.n

CONTENT

1. General description 2

2. Getting started 3

2.1 Insert a SIM card 3

2.2 Insert the batteries 3

2.3 Connect an external power supply 4

2.4 Program at least one telephone number 4

2.5 Switching on/off 5

2.6 Confirmation of the alarm message 5

3. Connect sensors to the inputs 6

4. Configuration 7

4.1 Program mode 7

4.2 The (security) code 8

4.3 Programming the settings by SMS 8

4.4 List of SMS commands for configuration 9

5. Possible settings 11

5.1 Phone numbers 11

5.2 Identification text 11

5.3 Alarm texts 12

5.4 SMS on/off 12

5.5 Call on/off 12

5.6 Input type 13

5.7 Exit delay time 13

5.8 Alarm delay time 13

5.9 Inactive time 14

5.10 Alarm repeat time 14

5.11 Power failure delay time 14

5.12 Power failure message 15

5.13 Automatic arming / disarming 15

5.14 Buttonlock 16

5.15 Low power mode 17

5.16 Test message 17

5.17 System reset 17

6. Request list of the status, settings and signal strength 18

7. Mobeye Internet Portal 19

8. Technical messages and status feedback 20

Attention! Very important

This user manual contains important guidelines for the installation and usage of the Mobeye®

device as described in this manual. Please read these thoroughly before you start using the

Mobeye® device.

In case of damage caused by disregarding the guidelines, the warranty becomes void.

The user must regularly check the proper functioning of the device. The manufacturer cannot

be held liable for any damage or loss caused by any incorrect use or incorrect functioning of

the Mobeye® device.

Safety guidelines

• The permitted ambient temperature during operation may not be exceeded (not lower

than -10°C and not higher than 50°C).

• The device is intended for use in dry and clean places.

• Protect the device from moisture, heat and water splashing. Not intended for external use.

• The guidelines for the battery usage must be regarded.

• Do not expose the device to strong vibrations.

• Do not let it fall from height.

• Do not use in an environment where any inflammable gases, vapors or dust are present

or could be present.

• Repair of the device may only be carried out by people, trained for Mobeye®repair.

• If the device must be repaired, only original replacement components may be used. The

use of different parts may lead to damage of the Mobeye®device.

Use in accordance with the regulations

The purpose of this device in accordance with the regulations is sending SMS text messages

and making telephone calls after an alarm situation. Other uses are not permitted and may

invalidate the warranty.

Battery recycling

CR123 batteries, as used in the Mobeye PowerGuard, are classified as non-hazardous waste

and can be recycled. Please take empty batteries to a nearest collection point.

1. GENERAL DESCRIPTION

The Mobeye PowerGuard is a battery operated GSM module used to send an alarm

notification after power failure or after a triggered input.

The factory settings of the Mobeye PowerGuard cause following reactions:

- When a power failure occurs, the Mobeye PowerGuard sends an alarm SMS text

message and calls the phone numbers programmed in by the user.

- When the power is restored, the Mobeye PowerGuard sends a ‘power restored’

SMS text message.

- When one of the inputs is activated by a sensor, the Mobeye PowerGuard sends

an alarm SMS text message and calls the phone numbers programmed in by the

user.

- When one of the inputs remain in the alarm status, the Mobeye PowerGuard

repeats sending the SMS alarm message every four hours.

- When the batteries need to be replaced, the Mobeye PowerGuard sends a ‘low

battery’SMS text message to the first telephone number (administrator).

The Mobeye PowerGuard has many options to influence the behaviour, which are

described in chapter 4. For additional alarm and monitoring functions the Mobeye

PowerGuard can be connected to the Mobeye Internet Portal, which is explained in

chapter 7.

2. GETTING STARTED

To get started with the Mobeye PowerGuard, at least the following steps need to be

taken in the following order:

1. Insert a SIM card

2. Insert the batteries

3. Connect an external power supply

4. Program at least one telephone number

5. Arming/disarming the system

These steps are further explained in this chapter. After these steps the module will be

operational.

2.1 INSERT A SIM CARD

Open the enclosure by removing the 4 screws and insert a SIM card into the module.

Push the black cover slightly outward to open the holder. Before installing the SIM

card should have PIN code "0000", or PIN code removed.

(A PIN code can be changed or removed by putting the SIM card in to any mobile phone and entering

the 'security' menu).

NB: Make sure the SIM card is inserted before the batteries are inserted. If you

replace a SIM card, first remove the batteries (and remove any other external power

supply). The settings are stored in the device memory. The SIM card shall have the

“normal” size and be suitable for 2G. It is advised to use an M2M SIM card.

2.2 INSERT THE BATTERIES

Insert the two batteries (CR123) in the module. Use the +/- indication for the correct

placement.

2.3 CONNECT AN EXTERNAL POWER SUPPLY

Connect the external power adapter (or any

other regulated 12VDC power supply) to the

power input of the connector (press on the

green pins to connect the wires):

- V+ (black lead with white stripe) to “+”

- Ground (black lead) to “-“

As soon as the batteries are placed and the power source is connected, the Mobeye

PowerGuard switches to the program mode. First the GSM module establishes

network connection. During this time the LED flashes green and red. Within 10-30

seconds the connection is established and the status LED starts flashing 1 sec. on/1

sec. off (or stays on continuously in case the first telephone number has been

configured).

2.4 PROGRAM AT LEAST ONE TELEPHONE NUMBER

The Mobeye PowerGuard is able to send messages up to 5 telephone numbers. The

first telephone number (TEL1) belongs to the administrator. Technical messages (such

as battery low) are sent to the administrator only. Without the administrators’phone

number, the Mobeye PowerGuard cannot function.

When the PowerGuard is in initial (factory) status and the batteries are inserted (so the

LED is flashing), the administrators’number is programmed by calling the telephone

number of the Mobeye PowerGuard using the administrators’ phone. The unit will

recognize this number and store it as administrator (TEL1). The administrator will

receive a confirmation SMS text message including the security code. This code is

needed to program the other settings in the unit.

NB: For this way of programming the number recognition in the administrator’s phone

must be ‘on’. To program or change the administrators’ number by SMS command,

please refer to 4.2.

2.5 SWITCHING ON/OFF

After the previous steps, the Mobeye PowerGuard is ready for use. It is armed

(switched on) automatically.

In order to switch off (disarm) the Mobeye PowerGuard:

- Press the on/ off button at the upper side for 1 second. The green LED switches off

to indicate the disarmed status.

In the disarmed status the Mobeye PowerGuard will not send alarm notifications.

The functions automatic arming and sending a ‘low battery’message, are still

active.

In order to switch on (arm) the Mobeye PowerGuard:

- Press the on/ off button at the upper side for 1 second. The green LED blinks once

every 3 seconds (battery-powered) or stays ‘on’ continuously (in case of an

external power supply).

If powered externally (GSM is open), switching can be done via SMS commands:

SMS-command to switch on: CODE ARM

SMS-command to switch off: CODE DISARM

example: 1111 ARM

The status can be requested via SMS command CODE STATUS? (see chapter 6).

2.6 CONFIRMATION OF THE ALARM MESSAGE

When the system is triggered it will send alarm notifications. First an SMS text

message is sent to all programmed alarm numbers, followed by a phone call. When

you pick up the phone, you will hear beeps. It is possible to confirm the phone call by

answering the phone and pressing any key. The other alarm numbers will not be

called afterwards.

By switching off the ‘SMS’ function, the system will only call. This prevents the other

numbers being notified by SMS.

3. CONNECT SENSORS TO THE INPUTS

Two external sensors can be connected to the inputs. As a standard reaction after a

triggered input, the Mobeye PowerGuard sends an SMS text message to the preset

numbers and calls these numbers.

Insert the 2 wires of an external sensor through

the hole in the enclosure and insert them in the

two connectors of input 1 (press on the green

pins for connecting the wires). It does not matter

which wire is connected to which connector.

A second sensor can be connected to input 2.

As default the inputs are programmed as Normally Open (NO) contacts. This means

the inputs are triggered if the input is closed for at least 1 second. In case the contact

is Normally Closed (NC), please refer to paragraph 5.4. If you require the sensor to be

activated for a shorter or longer period before triggering an alarm, please refer to 5.7.

4. CONFIGURATION

To program the Mobeye PowerGuard, the GSM module must have network

connection. In case only batteries are used, first switch the unit to the program mode.

Next send SMS commands for the configuration. All settings are stored and will be

kept in the unit, even in case the power supplies are removed.

4.1 PROGRAM MODE

If the unit is connected to an external power supply, the PowerGuard has continuous

network connection and the unit is permanently in program mode.

If the unit is battery-powered the program mode can be achieved by pressing the

on/off button for 5 seconds, until the LED starts flashing red and green. Alternatively,

the program mode can be accessed by (re) inserting the batteries.

First the GSM module establishes network connection. During this time the LED

flashes green/red. Normally this takes 10-30 seconds. Once the connection is

established the status LED starts flashing 1 sec. on/1 sec. off (or stays on continuously

in case the first telephone number has been configured).

In program mode, the device is ready to receive SMS commands. If no correct

command is received for 3 minutes, the GSM module switches off in order to save the

batteries. The unit returns to the low power operational mode.

The program mode is interrupted by pressing the on/off button for one second until the

LED switches off. The unit is switched off completely (disarmed).

Otros manuales para PowerGuard CM2100

Tabla de contenidos

Otros manuales de Sistema de seguridad de Mobeye

Mobeye

Mobeye ThermoGuard CM2200 Manual de usuario

Mobeye

Mobeye CMVXI-R Manual de usuario

Mobeye

Mobeye CM2500 Manual de usuario

Mobeye

Mobeye i110 Manual de usuario

Mobeye

Mobeye CM2500 Manual de usuario

Mobeye

Mobeye CM2500 Manual de usuario

Mobeye

Mobeye argos i200 Manual de usuario

Mobeye

Mobeye ThermoGuard TwinLog CML2255 Manual de usuario

Mobeye

Mobeye i110 Manual de usuario

Mobeye

Mobeye CM4000 Manual de usuario

Mobeye

Mobeye CombiGuard CM2600 Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario