MMcall T10 Manual de usuario
MMCallUS.com | 1
USER MANUAL | T10 & NC8/NS8
Table of Contents
Setup and Use .............................................................................................. 3
Charger........................................................................................................ 3
Host.............................................................................................................. 4
Call a Pager.................................................................................................. 5
Send Preset and Custom Messages ............................................................. 5
Call All Pagers .............................................................................................. 6
Transmitter Settings .................................................................................... 6
Change Transmitter Time ............................................................................ 7
Assigning Default and Preset Messages ....................................................... 7
Turn ON/OFF the Beepers/Watches............................................................ 8
Delete Messages ......................................................................................... 8
Charge Beepers/Watches ............................................................................ 8
Change Beeper/Watch Time ....................................................................... 9
Change Display Timeout............................................................................ 10
Change Vibration Length ........................................................................... 11
Troubleshooting......................................................................................... 12
If Pager does not Receive Pages ................................................................ 12
Check the Power Supply ............................................................................ 12
Charging Check.......................................................................................... 13
MMCallUS.com | 2
USER MANUAL | T10 & NC8/NS8
Service Questions and Answers ................................................................. 13
What to do if the system malfunctions?.................................................... 13
System Repair after Warranty Expiration .................................................. 13
Ordering Additional Pagers ....................................................................... 13
Product Specifications................................................................................ 13
Warranty.................................................................................................... 14
FCC Interference Statement....................................................................... 14
MMCallUS.com | 3
USER MANUAL | T10 & NC8/NS8
Setup and Use
•Plug power cord into outlet, then plug other end into transmitter.
•Attach antennae by fitting and twisting to the right.
•To turn on pagers, hold the RIGHT arrow for 5 seconds.
•The Pager display will show the number (01, 02, etc.) in the bottom
right corner.
•To wake up the pager from display sleep, hold the RIGHT arrow for 1
second.
Pager Charger
Plug cable into charging dock for watches, and directly into beepers (see
page 8-9).
MMCallUS.com | 4
USER MANUAL | T10 & NC8/NS8
How to use the Transmitter?
F1: Home Screen
F4: Settings
SEND: Call Pager
*<- : Delete
# S :Numeric / Capitalize
/ Loser Case
MMCallUS.com | 5
USER MANUAL | T10 & NC8/NS8
Call a Pager
When calling a staff member, enter the pager number. To send the
Default message (see settings page 7) simply press SEND:
You will know the signal was sent when the image next to the time
appears, and the number is highlighted by the cursor.
Calling the Pager with Preset Messages
When sending customized preset messages (see settings
page 7), press ENT after inputting the pager number, but
before pressing SEND. Scroll up or down with arrows to view these
messages. Press SEND to send just this message.
Adding Custom Messages
When sending custom messages, or adding to the preset messages,
press ENT after inputting the pager number. To add to the preset
message (i.e. Instead of "Example 1" to read "Example 1 ASAP") have
Example 1 chosen, then press ENT again instead of SEND. Use the #
MMCallUS.com | 6
USER MANUAL | T10 & NC8/NS8
key to shift between numeric and upper/lower case letters.
Press "2" twice for "B", etc. and "0" for space.
To send a completely new message, choose a blank entry in the
preset messages, and press ENT, then input the message.
Press SEND to send the custom message.
Call All Pagers
1. When calling all staff/server, enter 99 and press SEND:
Transmitter Settings
Press F4 in the bottom right corner. Enter 1234 as the password, and then
press ENT.
MMCallUS.com | 7
USER MANUAL | T10 & NC8/NS8
Change Time:
1. Use numbers on transmitter to change time, press UP or Down to adjust
AM/PM or 25 hour mode. Press ESC when done.
2. Press F1 to exit settings menu.
Default and Preset Messages
Menu #5: Preset Message (Default): Initial message sent without additional
messages (often preset as “Please Return to Counter”).
a. Use the “#S”Key to choose between numeric or alphabet characters,
then type out message. Press “2” twice to get “B”, etc. and “0” for a
space.
Menu #6: Message (preset): Additional messages to choose from.
a. Message 1: Press ENT and input message. Press ENT when done,
then ESC to leave that menu. Scroll up or down to change Message
2-9.
b. Note: to send completely custom messages later (i.e. without preset
words) one of these 9 messages must remain blank.
MMCallUS.com | 8
USER MANUAL | T10 & NC8/NS8
How to use the Beepers/Watches?
Turn ON/OFF the Beepers/Watches
To turn ON/OFF beepers/watches, hold the RIGHT arrow for 5-10 seconds. If
by any chance the pager does not turn on, plug it in to the charger.
To wake the pager up from display sleep, hold the RIGHT arrow for 1 second.
Delete Messages
To delete messages from the pager, press the LEFT arrow. Press OK to see a
full list of all pending messages.
Charge Pagers
To charge the watch, place on the charging square with the pins going into
the connectors on the bottom of the watch. Pager should say "Charging..."
MMCallUS.com | 9
USER MANUAL | T10 & NC8/NS8
To charge the beepers, lift the rubber on the side and connect the micro USB.
Pager should say "Charging..."
Pager Settings
To access settings, hold LEFT arrow until password appears.
(Next step must be done quickly) To enter the password, use RIGHT arrow to
move cursor to last number (4) and use LEFT arrow to change to 5. Password
should read 1235. Press OK.
Change Pager Time
1. See “1-Clock Setup” as the first menu item. Press OK when option is
highlighted.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
