ML Accessories OSPCKIT Manual de instrucciones

INSTALLATION & MAINTENANCE MANUAL

OSPCKIT

These instructions should be read carefully and retained after installation by the end user for

future reference and maintenance.

These instructions should be used to aid the installation of the following product:

OSPCKIT

GENERAL INSTRUCTIONS

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)

and current Building Regulations. If in any doubt, consult a qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this product is ﬁtted) does not exceed the rating of the

circuit cable, fuse, or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

• Do not overload this accessory or subject it to conditions outside its rating

• This product is Class II double insulated

• This product is IP66 rated

SAFETY

INSTALLATION

• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable IP

rated junction boxes should be used where required

• The power source connections should be local and accessible via a suitable IP rated enclosure

• Round cable should be used for the mains supply. The use of ﬂat cable will cause water ingress to the sensor

• Using the mounting bracket as a template, mark the location for, and drill the ﬁxing holes ensuring not to

infringe with any gas/water pipes or electrical cables

• Fix the bracket to a suitable solid surface using the screws provided

• Unscrew the three screws on the bottom of the sensor and remove the plastic cover

• Feed the cables through the compression glands on the bottom of the sensor

• Connect the sensor to the mains supply ensuring the correct polarity is observed (see Fig. 1): L - Live

(brown), N - Neutral (blue)

• Connect the load to the sensor ensuring the correct polarity is observed (see Fig. 1): L - Live (brown),

N - Neutral (blue)

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid the installation of the following product:

OSPCKIT

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this product is fitted) does not exceed the rating of

the circuit cable, fuse, or circuit breaker

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•Do not overload this accessory or subject it to conditions outside its rating

•This product is Class II double insulated

•This product is IP66 rated

INSTALLATION

•Provide power to the required point of installation (refer to BS7671 for correct cabling methods).

Suitable IP rated junction boxes should be used where required

•The power source connections should be local and accessible via a suitable IP rated enclosure

•Round cable should be used for the mains supply. The use of flat cable will cause water ingress to the

fitting

•Using the mounting bracket as a template, mark the location for, and drill the fixing holes ensuring not

to infringe with any gas/water pipes or electrical cables

•Fix the bracket to a suitable solid surface using the screws provided

•Unscrew the three screws on the bottom of the sensor and remove the plastic cover

•Feed the cables through the compression glands on the bottom of the sensor

•Connect the sensor to the mains supply ensuring the correct polarity is observed (see Fig. 1): L - Live

(brown), N - Neutral (blue)

•Connect the load to the sensor ensuring the correct polarity is observed (see Fig. 1): L - Live (brown),

N - Neutral (blue)

Fig. 1

•Adjust the lux level

•Reattach the plastic cover and tighten the compression glands

•Slide the sensor onto the mounting bracket

•Switch on and check for correct operation

Fig. 1

• Adjust the lux level

• Reattach the plastic cover and tighten the compression glands

• Slide the sensor onto the mounting bracket

• Switch on and check for correct operation

SENSOR SETTING

• By turning the knob with the aid of a small ﬂat-head screwdriver, the lux levels can be adjusted from a

minimum of 10 lux to a maximum of 50 lux (see Fig. 2)

SENSOR SETTING

•By turning the knob with the aid of a small flat-head screwdriver, the lux levels can be adjusted from a

minimum of 10 lux to a maximum of 50 lux, see Fig. 2

Fig .2

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not

use aggressive cleaning products or solvents which may damage the product.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

WARRANTY

This product has a warranty of 1 year from the date of purchase. Failure to install this product in accordance

with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will

invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of

purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve

the right to alter product specification without prior notice.

230V 50Hz, IP66, Class II

AVJUL21_V1

EU authorised representative: SLV Group Holdings GmbH, Niederkasseler Lohweg 18, Germany – 40547 Düsseldorf

Contact: eprel@group.slv.com

Fig. 2

WARNING

GENERAL

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do

not use aggressive cleaning products or solvents which may damage the product.

This product should be recycled in the correct manner when it reaches the end of its life. Check local

authorities for where facilities exist.

WARRANTY

This product has a warranty of 1 year from the date of purchase. Failure to install this product in accordance

with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch

code will invalidate the warranty. If this product should fail within its warranty period, it should be returned

to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for

any installation costs associated with the replacement product. Your statutory rights are not affected. ML

Accessories reserve the right to alter product speciﬁcation without prior notice.

AVJUL21_V1

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

116

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

Tabla de contenidos

Otros manuales de Equipo de iluminación de ML Accessories

ML Accessories

ML Accessories RWL2A Manual de instrucciones

ML Accessories

ML Accessories Knightsbridge SPIKEW Manual

ML Accessories

ML Accessories SPIKE5S Manual de instrucciones

ML Accessories

ML Accessories EMPOWER3 Manual de instrucciones

ML Accessories

ML Accessories MLBA6045 Series Manual de instrucciones

ML Accessories

ML Accessories FL8ABK Manual de instrucciones

ML Accessories

ML Accessories LEDFRA1 Manual de instrucciones

ML Accessories

ML Accessories SURF236HF Manual de instrucciones

ML Accessories

ML Accessories EAPIR1BK Manual de instrucciones

ML Accessories

ML Accessories FLP Series Manual de instrucciones

ML Accessories

ML Accessories BATS2 Manual de instrucciones

ML Accessories

ML Accessories UNDKIT3WWW Manual de instrucciones

ML Accessories

ML Accessories SURF236EMHF Manual de instrucciones

ML Accessories

ML Accessories 4IPB Manual de instrucciones

ML Accessories

ML Accessories T8BLED15EM1 Manual de instrucciones

ML Accessories

ML Accessories RD1 Series Manual de instrucciones

ML Accessories

ML Accessories EA1 Series Manual de instrucciones

ML Accessories

ML Accessories BATSCWST4 Manual de instrucciones

ML Accessories

ML Accessories SURF418HF Manual de instrucciones

ML Accessories

ML Accessories POTHB1 Manual de instrucciones

ML Accessories

ML Accessories Knightsbridge SFPL Series Manual de instrucciones

ML Accessories

ML Accessories LFC24B M Series Manual de instrucciones

ML Accessories

ML Accessories Knightsbridge LEDFS12WW Manual de instrucciones

ML Accessories

ML Accessories RW6WW Manual de instrucciones

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario