Mitsubishi GOT1000 Series Manual de instrucciones

GOT1000 Series Connection Manual

MODEL

CODE

GT1000-U(CON)-E

1D7M26

SH(NA)-080532ENG-C1/2(0510)MEE

Specifications subject to change without notice.

When exported from Japan, this manual does not require application to the

Ministry of Economy, Trade and Industry for service transaction permission.

HEAD OFFICE : 1-8-12, OFFICE TOWER Z 14F HARUMI CHUO-KU 104-6212,JAPAN

NAGOYA WORKS : 1-14 , YADA-MINAMI 5-CHOME , HIGASHI-KU, NAGOYA , JAPAN

1/2

A - 1

SAFETY PRECAUTIONS

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual

carefully and pay full attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "DANGER" and "CAUTION".

Note that the caution level may lead to a serious accident according to the circumstances.

Always follow the instructions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

[DESIGN PRECAUTIONS]

DANGER

Some failures of the GOT, communication unit or cable may keep the outputs on or off.

An external monitoring circuit should be provided to check for output signals which may lead to a

serious accident.

Not doing so can cause an accident due to false output or malfunction.

If a communication fault (including cable disconnection) occurs during monitoring on the GOT,

communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative.

For bus connection : The CPU becomes faulty and the GOT becomes inoperative.

For other than bus connection : The GOT becomes inoperative.

A system where the GOT is used should be configured to perform any significant operation to the

system by using the switches of a device other than the GOT on the assumption that a GOT

communication fault will occur.

Not doing so can cause an accident due to false output or malfunction.

Do not use the GOT as the warning device that may cause a serious accident.

An independent and redundant hardware or mechanical interlock is required to configure the device

that displays and outputs serious warning.

Failure to observe this instruction may result in an accident due to incorrect output or malfunction.

DANGER Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

CAUTION Indicates that incorrect handling may cause hazardous conditions,

resulting in medium or slight personal injury or physical damage.

A - 2

[DESIGN PRECAUTIONS]

[MOUNTING PRECAUTIONS]

DANGER

Incorrect operation of the touch switch(s) may lead to a serious accident if the GOT backlight is gone

out.

When the GOT backlight goes out, the POWER LED flickers (green/orange) and the display section

turns black and causes the monitor screen to appear blank, while the input of the touch switch(s)

remains active.

This may confuse an operator in thinking that the GOT is in "screensaver" mode, who then tries to

release the GOT from this mode by touching the display section, which may cause a touch switch to

operate.

Note that the following occurs on the GOT when the backlight goes out.

The POWER LED flickers (green/orange) and the monitor screen appears blank.

CAUTION

Do not bundle the control and communication cables with main-circuit, power or other wiring.

Run the above cables separately from such wiring and keep them a minimum of 100mm apart.

Not doing so noise can cause a malfunction.

DANGER

Be sure to shut off all phases of the external power supply used by the system before mounting or

removing the GOT to/from the panel.

Not doing so can cause the GOT to fail or malfunction.

Be sure to shut off all phases of the external power supply used by the system before mounting or

removing the communication unit, option function board or multi-color display board onto/from the GOT.

Not doing so can cause the unit to fail or malfunction.

Before mounting an optional function board or Multi-color display board, wear a static discharge wrist

strap to prevent the board from being damaged by static electricity.

CAUTION

Use the GOT in the environment that satisfies the general specifications described in this manual.

Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

When mounting the GOT to the control panel, tighten the mounting screws in the specified torque

range.

Undertightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the

GOT.

A - 3

[MOUNTING PRECAUTIONS]

[WIRING PRECAUTIONS]

CAUTION

When loading the communication unit to the GOT, fit it to the connection interface of the GOT and

tighten the mounting screws in the specified torque range.

Overtightening can cause a drop, failure or malfunction due to the damage of the screws or unit.

When mounting the multi-color display board onto the GOT, tighten the mounting screws within the

specified torque range.

Loose tightening may cause the unit and/or GOT to malfunction due to poor contact.

Overtightening may damage the screws, unit and/or GOT; they might malfunction.

When mounting an optional function board onto the GT15 , fully connect it to the connector until

you hear a click.

When mounting an optional function board onto the GT15 , fully connect it to the connector.

Push the multi-color display board onto the corresponding connector so that it will be secured firmly.

When inserting a CF card into the GOT, push it into the insertion slot until the CF card eject button

will pop out.

Failure to do so may cause a malfunction due to poor contact.

When inserting/removing a CF card into/from the GOT, turn the CF card access switch off in

advance.

Failure to do so may corrupt data within the CF card.

When removing a CF card from the GOT, make sure to support the CF card by hand, as it may pop

out.

Failure to do so may cause the CF card to drop from the GOT and break.

DANGER

Be sure to shut off all phases of the external power supply used by the system before wiring.

Failure to do so may result in an electric shock, product damage or malfunctions.

A - 4

[WIRING PRECAUTIONS]

CAUTION

Please make sure to ground FG terminal and LG terminal of the GOT power supply section by

applying Class D Grounding (Class 3 Grounding Method) or higher which is used exclusively for the

GOT.

Not doing so may cause an electric shock or malfunction.

Be sure to tighten any unused terminal screws with a torque of 0.5 to 0.8N•m.

Failure to do so may cause a short circuit due to contact with a solderless terminal.

Use applicable solderless terminals and tighten them with the specified torque.

If any solderless spade terminal is used, it may be disconnected when the terminal screw comes

loose, resulting in failure.

Correctly wire the GOT power supply section after confirming the rated voltage and terminal

arrangement of the product.

Not doing so can cause a fire or failure.

Tighten the terminal screws of the GOT power supply section in the specified torque range.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or the GOT.

Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT. Not doing so

can cause a fire, failure or malfunction.

Plug the bus connection cable by inserting it into the connector of the connected unit until it "clicks".

After plugging, check that it has been inserted snugly.

Not doing so can cause a malfunction due to a contact fault.

Plug the communication cable into the connector of the connected unit and tighten the mounting and

terminal screws in the specified torque range.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

A - 5

[TEST OPERATION PRECAUTIONS]

[STARTUP/MAINTENANCE PRECAUTIONS]

DANGER

Before performing the test operations of the user creation monitor screen (such as turning ON or

OFF bit device, changing the word device current value, changing the settings or current values of

the timer or counter, and changing the buffer memory current value), read through the manual

carefully and make yourself familiar with the operation method.

During test operation, never change the data of the devices which are used to perform significant

operation for the system.

False output or malfunction can cause an accident.

DANGER

When power is on, do not touch the terminals.

Doing so can cause an electric shock or malfunction.

Connect the battery correctly.

Do not discharge, disassemble, heat, short, solder or throw the battery into the fire.

Incorrect handling may cause the battery to generate heat, burst or take fire, resulting in injuries or

fires

Before starting cleaning or terminal screw retightening, always switch off the power externally in all

phases.

Not switching the power off in all phases can cause a unit failure or malfunction.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

A - 6

[STARTUP/MAINTENANCE PRECAUTIONS]

[BACKLIGHT REPLACEMENT PRECAUTIONS]

CAUTION

Do not disassemble or modify the unit.

Doing so can cause a failure, malfunction, injury or fire.

Do not touch the conductive and electronic parts of the unit directly.

Doing so can cause a unit malfunction or failure.

The cables connected to the unit must be run in ducts or clamped.

Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidental

pulling of the cables or can cause a malfunction due to a cable connection fault.

When unplugging the cable connected to the unit, do not hold and pull the cable portion.

Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable

connection fault.

Do not drop or apply strong impact to the unit.

Doing so may damage the unit.

Do not drop or give an impact to the battery mounted to the unit.

Doing so may damage the battery, causing the battery fluid to leak inside the battery.

If the battery is dropped or given an impact, dispose of it without using.

Before touching the unit, always touch grounded metal, etc. to discharge static electricity from

human body, etc.

Not doing so can cause the unit to fail or malfunction.

DANGER

Be sure to shut off all phases of the external power supply of the GOT (and the PLC CPU in the case

of a bus topology) and remove the GOT from the control panel before replacing the backlight (when

using the GOT with the backlight replaceable by the user).

Not doing so can cause an electric shock.

Replacing a backlight without removing the GOT from the control panel can cause the backlight or

control panel to drop, resulting in an injury.

CAUTION

Wear gloves for the backlight replacement when using the GOT with the backlight replaceable by the

user.

Not doing so can cause an injury.

Before replacing a backlight, allow 5 minutes or more after turning off the GOT when using the GOT

with the backlight replaceable by the user.

Not doing so can cause a burn from heat of the backlight.

A - 7

[DISPOSAL PRECAUTIONS]

[TRANSPORTATION PRECAUTIONS]

CAUTION

When disposing of the product, handle it as industrial waste.

CAUTION

When transporting lithium batteries, make sure to treat them based on the transport regulations.

(For details on models subject to restrictions, refer to the User's Manual for the GOT you are using.)

Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be

exposed to the impact exceeding the impact resistance described in the general specifications of the

User's Manual, as they are precision devices.

Failure to do so may cause the unit to fail.

Check if the unit operates correctly after transportation.

A - 8

REVISIONS

* The manual number is given on the bottom left of the back cover.

This volume is SH(NA)-080532ENG-D 1/2.

Print Date * Manual Number Revision

Oct., 2004 SH(NA)-080532ENG-A First edition

Mar., 2005 SH(NA)-080532ENG-B Compatible with GT Designer2 Version2.09K

Chapter 5, Chapter 6, Chapter 7, Chapter 8, Chapter 10, Chapter 11,

Chapter 12, Chapter 13, Chapter 19, Chapter 20, Chapter 21, Chapter 22,

Chapter 23,Section 3.1.8, Section 3.1.9

Revised throughout the manual due to addition of the new connection types and

functions.

SAFETY PRECAUTIONS, ABBREVIATIONS AND GENERIC TERMS IN THIS

MANUAL, HOW TO READ THIS MANUAL, Chapter 1, Section 1.1, 1.2, 2.1.3,

2.1.5, 2.1.7, 2.3, 3.1.4, 3.1.5, 3.1.6, 3.1.7, 4.1.7, 4.4.1, 14.1.3, 14.2, 15.3.3,

21.3, 21.4.4, 21.5

Oct., 2005 SH(NA)-080532ENG-C Compatible with GT Designer2 Version2.18U

Chapter 10, Chapter 20, Chapter 21, Chapter 22, Chapter 23, Chapter 26,

Chapter 27, Section 14.1.9, Section 18.1.2, Section 24.4.3

Revised throughout the manual due to addition of the new connection types and

functions.

SAFETY PRECAUTIONS, ABBREVIATIONS AND GENERIC TERMS IN THIS

MANUAL, HOW TO READ THIS MANUAL, Chapter 1 to 9, Chapter 11 to 19,

Chapter 24, Chapter 25

Chapter 28 to 30

Separated the manual as the following.

SH(NA)-080532ENG-C 1/2:Chapter 1 to 18

SH(NA)-080532ENG-C 2/2:Chapter 19 to 30

Addition

Section numbers revised

Partial correction

Addition

Section numbers revised

Partial correction

Volume separated

Otros manuales para GOT1000 Series

Tabla de contenidos

Otros manuales de Terminal táctil de Mitsubishi

Mitsubishi

Mitsubishi F940 Manual de usuario

Mitsubishi

Mitsubishi GOT1000 GT11 Manual de usuario

Mitsubishi

Mitsubishi MELSEC GOT-F900 Manual de usuario

Mitsubishi

Mitsubishi GT16 Manual de usuario

Mitsubishi

Mitsubishi F940 Manual de usuario

Mitsubishi

Mitsubishi A950GOT Manual de usuario

Mitsubishi

Mitsubishi GT10 Manual de usuario

Mitsubishi

Mitsubishi GOT1000 Series Manual de instrucciones

Mitsubishi

Mitsubishi GOT MELSEC 800 Series Manual de usuario

Mitsubishi

Mitsubishi GT16 Manual de usuario

Mitsubishi

Mitsubishi GOT-A900 Series Manual de usuario

Mitsubishi

Mitsubishi F940GOT Handy Series Manual de usuario

Mitsubishi

Mitsubishi GOT MELSEC 800 Series Manual de usuario

Mitsubishi

Mitsubishi 900 Series Manual de usuario

Mitsubishi

Mitsubishi F930GOT-BBD-K-E Manual de usuario

Mitsubishi

Mitsubishi GT10 Manual de usuario

Mitsubishi

Mitsubishi G0T-A900 Series Manual de usuario

Mitsubishi

Mitsubishi GT14 Manual de usuario

Mitsubishi

Mitsubishi GT11 Manual de usuario

Mitsubishi

Mitsubishi GT1150-QLBD Manual de usuario

Mitsubishi

Mitsubishi GOT1000 GT15 Manual de usuario

Mitsubishi

Mitsubishi F940GOT-SWD-E Manual de usuario

Mitsubishi

Mitsubishi 900 Series Manual de usuario

Mitsubishi

Mitsubishi F940WGOT-TWD Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario