Mitsubishi Electric GT1020 Series Guía del usuario

Note: This document is for reference only. For detailed settings and safety information refer to the respective product manual.

GT1020/GT1030 to FX Connection

START

STARTSTART

START

UP GUIDE

UP GUIDEUP GUIDE

UP GUIDE

Note: This document is for reference only. For detailed settings and safety information refer to the respective product manual.

GOT1000 Startup Guide Ver. A

GT1020/GT1030-to-FX Connection

Overview:

This document provides a simple guide and reference for setting up the

GT1020 or GT1030 Graphic Operation Terminal (GOT) hardware and

firmware for use with an FX Series PLC.

Hardware Introduction:

The GT1020 and GT1030 are monochrome, 3-color backlight, two

communication channel GOT1000 Series touch panel interfaces, and consist

of the following models:

Model Size Extension Backlight Colors Comm. IF Power

LBD RS-422

LBD2 Green/Orange/Red RS-232C

LBDW RS-422

LBDW2 White/Pink/Red RS-232C

24V DC

LBL Green/Orange/Red

GT1020 3.7”

160 x

64 dot

LBLW White/Pink/Red RS-422 5V DC

LBD RS-422

LBD2 Green/Orange/Red RS-232C

LBDW RS-422

GT1030 4.5”

288 x

96 dot LBDW2 White/Pink/Red RS-232C

24V DC

For new GT1020 and GT1030 units, included in the box should be the

GT1020/GT1030 (A), 1 PLC Communication Connector (B), 1 rubber Panel

Mounting Packing (C), and 4 Panel Mounting Brackets (D).

Cabling:

Power

All GT1020/GT1030 GOTs except for the GT1020-LBL

and GT1020-LBLW (5V DC versions) require an external 24V

DC power supply to be connected to the Power Terminal on

the back of the GOT. The 5V DC versions are powered

B C

Note: This document is for reference only. For detailed settings and safety information refer to the respective product manual.

through the communication cables, described below.

5V DC version GT1020 GOTs

The GT1020-LBL and GT1020-LBLW are the only two 5V DC GOTs in

the GOT1000 lineup. They are powered directly from the communication

cable, and can only be connected with an FX Series PLC. Other PLCs and

connectable products will not provide the necessary 5V DC power. The

power terminals have been removed from the 5V DC versions.

Communication

For the GT1020/GT1030 to communicate with an FX Series PLC, a

dedicated communication cable is required to connect the provided PLC

Communication Connector with the Programming Port (RS-422 8-pin Mini-

DIN) or other communication channel of the FX (RS-422 8-pin Mini-DIN or

RS-232C 9-pin D-sub). The cable names and length and specific wiring for

each case are illustrated below:

Connection to an RS-422 FX communication channel

Cable Name Length Applicable GOTs FX Comm. Equipment

GT10-C10R4-8P* 1m

GT10-C30R4-8P* 3m

GT10-C100R4-8P 10m

GT10-C200R4-8P 20m

GT10-C300R4-8P 30m

GT1020-LBD

GT1020-LBDW

GT1030-LBD

GT1030-LBDW

Programming Port

FX3U-422-BD

FX2N-422-BD

FX1N-422-BD

* - Only the GT10-C10R4-8P and GT10-C30R4-8P apply to the GT1020-LBL and GT1020-

LBLW GOTs (5V DC versions).

Connection to an RS-232C FX communication channel

Cables Applicable GOTs FX Comm. Equipment

All RS-232C

GT1020/GT1030-to-FX

connection cables must be

made by the user as

described below.

GT1020-LBD2

GT1020-LBDW2

GT1030-LBD2

GT1030-LBDW2

FX3U-232-BD

FX3U-232ADP(-MB)*

FX2N-232-BD

FX2NC-232ADP*

FX1N-422-BD

Note: This document is for reference only. For detailed settings and safety information refer to the respective product manual.

* - Special Adapters require an additional FX**-CNV-BD or, for the FX3U only, a

Communication Expansion Board.

For all screw terminals on the GT1020/GT1030,

use a small flathead screwdriver to secure the wires

within the PLC Communication Connector

(recommended blade size and tightening torque:

0.4 x 2.5 mm and 0.22 to 0.25 N•m).

Programming Cables:

The GT1020 and GT1030 come pre-installed with an

OS and FX communication driver, but without any project

data. To download a project from a PC running GT Designer2

to the GOT, a programming cable is required that connects to

the RS-232C 6-pin Mini-DIN port on the back of the GOT. It

is recommended to use a shielded USB A-type to Mini-B type

cable with a ferrite core paired with the GT10-RS2TUSB-5S,

but any RS-232C programming cable for the Q-Series will

also work fine. A diagram of both is shown below.

QC30R2 (RS-232C)

USB + GT10-RS2TUSB-5S

PC GOT

Note: This document is for reference only. For detailed settings and safety information refer to the respective product manual.

Note that using the GT10-RS2TUSB-5S will require a virtual USB COM port

driver to be installed on the PC. The COM port number can be automatically

or manually assigned so that it does not overlap with the existing COM port

numbers assigned on that PC. When using a Q-Series programming cable,

the COM port number already assigned to the RS-232C interface of the PC

will have to be checked.

Example Connection Diagram:

The following is an example of an FX-to-GOT-to-PC connection, where

the blue lines indicate data communication and the red line indicates power

from the FX3U 24V DC service power supply.

Firmware Updates:

To make sure the GT1020/GT1030

GOT is able to use the latest functions and

features, it is the responsibility of the user to

check and update the firmware (Standard

monitor OS) of the GOT.

Launch the latest copy of GT Designer2 and

start a new project for the corresponding GOT model (GT1020 or GT1030)

with the “MELSEC-FX” Controller Type. Select “Yes” to set the

Communication Setting and make sure the Standard I/F-1 CH No. is set to 1

before selecting “OK”. The “Screen Property” window that pops up for making

a new screen can be either canceled or

accepted for the following steps.

Go to the “Communication” menu and

select “To/From GOT” to bring up the

“Communicate with GOT” window. Go to

the “Communication configuration” tab

and select “RS232” and the corresponding

“Port No.” that connects the PC to the

GOT. With the GOT power ON, use the

“Test” button to verify that the PC and

GOT can communicate properly then turn

the GOT power OFF.

GT10-RS2TUSB-5S + USB

FX3U-16MR-ES/UL

FX3U

422-BD

GT1020

LBD

(Back)

GT10-C100R4-8P

Note: This document is for reference only. For detailed settings and safety information refer to the respective product manual.

To access the OS installation mode of the GT1020/GT1030,

switch the GOT power from OFF to ON, while holding the

bottom right corner of the touch screen (in Horizontal

layout), illustrated to the right.

While the “Please install

the OS” screen is displayed, go to the “OS

Install -> GOT” tab in the “Communicate

with GOT” window of GT Designer2 and

select “Standard monitor OS” from the

data selection tree. Use the “Install”

button to initiate the data transfer and

update the firmware. Once the firmware

update has been completed the GOT will

automatically reboot and all features will

be up to date. Note that new project data

will need to be downloaded to the GOT.

Confirm Communication

Before downloading project data to the GOT, the Comm. Monitor

function can be used to verify that the GOT is communicating properly with

the PLC. If no error is shown, communication has been set up correctly.

Manual References:

Refer to the following manuals for more detailed explanations. For any

further questions, please contact your local Mitsubishi Product Provider.

GT10 User’s Manual (JY997D24701)

GT10 General Description (JY997D22901)

RS-232 / USB Conversion Adapter User’s Manual (JY997D23401)

GOT1000 Series Connection Manual 1/3 (SH(NA)-080532ENG)

- Sections 3.1.5, 3.1.6, 3.1.7, 3.2.1, 3.2.2

Power ON

Otros manuales para GT1020 Series

Este manual sirve para los siguientes modelos

Otros manuales de Terminal táctil de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric GT1665HS-VTBD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric F930GOT-BWD-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric E1071 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT1685 Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric GT11 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Guía de instalación

Mitsubishi Electric

Mitsubishi Electric GT16 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT SIMPLE GS2107-WTBD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Lossnay PZ-4GS-E Guía rápida

Mitsubishi Electric

Mitsubishi Electric GT2510-VTBA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT14 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric Got 1000 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT2104-PMBD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT 1000 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric F930GOT-BWD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT1155-QTBD Guía del usuario

Mitsubishi Electric

Mitsubishi Electric GT2512-STBA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT2508-VTBA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT 1000 Series Manual de instrucciones

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario