Mitsubishi Electric Melsec QJ71LP21 Manual de usuario

Q Corresponding MELSECNET/H

Network System

Reference Manual (PLC to PLC network)

-QJ71LP21

-QJ71LP21-25

-QJ71LP21S-25

-QJ71LP21G

-QJ71LP21GE

-QJ71BR11

-QJ71NT11B

A - 1 A - 1

• SAFETY PRECAUTIONS •

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full

attention to safety to handle the product correctly.

The instructions given in this manual are concerned with this product. For the safety instructions of the

programmable controller system, please read the CPU module user's manual.

In this manual, the safety precautions are classified into to levels: " WARNING" and " CAUTION".

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

• For operating status of each communication failure, refer to this manual. Incorrect output or

malfunction due to a communication failure may result in an accident.

• If a coaxial cable is disconnected, this may destabilize the line, and a network communication

error may occur in multiple stations. Provide an interlock circuit in the sequence program so that

the system will operate safely even if the above error occurs. Failure to do so may result in an

accident due to incorrect output or malfunction.

• When changing data of the running programmable controller from a peripheral connected to the

CPU module or from a personal computer connected to an intelligent function module or special

function module, configure an interlock circuit in the sequence program to ensure that the entire

system will always operate safely.

For program modification and operating status change, read relevant manuals carefully and

ensure the safety before operation.

Especially, in the case of a control from an external device to a remote programmable controller,

immediate action cannot be taken for a problem on the programmable controller due to a

communication failure.

To prevent this, configure an interlock circuit in the sequence program, and determine corrective

actions to be taken between the external device and CPU module in case of a communication

failure.

! !

A - 2 A - 2

[Design Precautions]

CAUTION

• Do not install the control lines or communication cables together with the main circuit lines or

power cables.

Keep a distance of 100mm or more between them.

Failure to do so may result in malfunction due to noise.

[Installation Precautions]

CAUTION

• Use the programmable controller in the operating an environment that meets the general

specifications given in the user's manual for the CPU module used.

Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of

the product.

• To mount the module, while pressing the module mounting lever located in the lower part of

module, fully insert the module fixing projection(s) into the hole(s) in the base unit press the

module until it snaps into place.

Incorrect mounting may cause malfunction, failure or drop of the module.

When using the programmable controller in an environment of frequent vibrations, fix the

module a screw.

Tighten the screw within the specified torque range.

Undertightening can cause drop of the screw, short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

• Shut off the external power supply for the system in all phases before mounting or removing the

module. Failure to do so may result in damage to the product.

• Do not directly touch any conductive part of the module.

Doing so can cause malfunction or failure of the module.

A - 3 A - 3

[Wiring Precautions]

WARNING

• Shut off the external power supply (all phases) used in the system before installation and wiring.

Failure to do so may result in electric shock or damage to the product.

CAUTION

• Individually ground the FG terminal of the programmable controller with a ground resistance of

100 or less.

Failure to do so may result in electric shock malfunction.

• Check the rated voltage and terminal layout before wiring to the terminal block for the external

power supply, and connect the cable correctly.

Connecting a cable to power supply with a different voltage rating or incorrect wiring may cause

a fire or failure.

• Tighten the terminal screw within the specified torque range.

Undertightening can cause drop of the screw, short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

• Properly solder the parts of a soldering-type coaxial cable connector. Incomplete soldering may

result in malfunction.

• Crimp the parts of a crimping-type coaxial cable connector with proper force at a proper position.

Failure to do so may cause drop of the cable or malfunction.

• Prevent foreign matter such as dust or wire chips from entering the module.

Such foreign matter can cause a fire, failure, or malfunction.

• A protective film is attached to the top of the module to prevent foreign matter, such as wire

chips, from entering the module during wiring.

Do not remove this film during wiring.

Remove it for heat dissipation before system operation.

• Place the cables in a duct or clamp them.

Failure to do so may cause damage of the module or the cables due to accidental pull or

unintentional shifting of the cables, or malfunctions due to poor contact of the cable.

• Do not install the control lines or communication cables together with the main circuit lines or

power cables.

Keep a distance of 100mm or more between them.

Failure to do so may result in malfunction due to noise.

• When disconnecting the communication and power cables from the module, do not pull the

cable by the cable part. Loosen the screws of connector before disconnecting the cable. When

disconnecting a cable connected to a terminal block, loosen the screws on the terminal block

first before removing the cable.

Failure to do so may result in damage to the module or cable or malfunction due to poor contact.

A - 4 A - 4

[Setup and Maintenance Precautions]

CAUTION

• Before performing online operations (especially, program modification, forced output, and

operation status change) for the running CPU module in other station from GX Developer via

MELSECNET/H, read relevant manuals carefully and ensure the safety.

• Do not disassemble or modify the module. Doing so may cause failure, malfunction, injury, or a

fire.

• Use any radio communication device such as a cellular phone or a PHS (Personal Handy-phone

System) more than 25cm (9.85 inches) away in all directions from the programmable controller.

Failure to do so may cause malfunction.

• Shut off the external power supply for the system in all phases before mounting or removing the

module. Failure to do so may cause the module to fail or malfunction.

• Do not touch any terminals while power is on. Doing so will cause electric shock.

• Shut external power supply for the system before cleaning the module or retightening the

terminal screws or module fixing screws.

Failure to do so may cause the module to fail or malfunction.

Undertightening can cause drop of the screw, short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

• After the firs use of the product, do not mount/remove the module to/from the base unit more

than 50 times (IEC 61131-2 compliant) respectively.

Exceeding the limit of 50 times may cause malfunction.

• Before handling the module, touch a grounded metal object to discharge the static electricity

from the human body.

Failure to do so may cause the module to fail or malfunction.

[Disposal Precautions]

CAUTION

• When disposing of this product, treat it as industrial waste.

A - 5 A - 5

• CONDITIONS OF USE FOR THE PRODUCT •

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major

or serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of

the PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT

LIMITED TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT,

WARRANTY, TORT, PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR

LOSS OR DAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR

USED IN APPLICATION NOT INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS,

OR WARNING CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY

MANUALS, TECHNICAL BULLETINS AND GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

 Nuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

 Railway companies or Public service purposes, and/or any other cases in which establishment of

a special quality assurance system is required by the Purchaser or End User.

 Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as

Elevator and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation,

Equipment for Recreation and Amusement, and Safety devices, handling of Nuclear or

Hazardous Materials or Chemicals, Mining and Drilling, and/or other applications where there is a

significant risk of injury to the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT

is limited only for the specific applications agreed to by Mitsubishi and provided further that no

special quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

A - 6 A - 6

REVISIONS

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Dec., 1999 SH(NA)-080049-A First printing

Oct., 2000 SH(NA)-080049-B Correction

Safety Precautions, Contents, About Manuals, About the Generic

Terms and Abbreviations, Chapter 1, Section 1.1, 1.2, Chapter 2,

Section 2.1.3, 2.1.4, 2.2.2, 3.1.1, 3.1.2, 3.2, 3.2.1, 3.2.2, 3.3, 3.3.1,

3.3.2, 3.3.3, 4.1, 4.2, 4.3.1, 4.3.2, 4.5, 4.5.1, 4.5.2, 4.5.3, 4.6.1, 4.6.2,

4.7, 4.7.1, 4.7.2, 4.8, 4.8.1, 4.8.2, 4.8.3, 4.8.4, Chapter 5, Section 5.1,

5.2, 5.2.3, 5.2.4, 5.2.5, 5.2.6, 5.5, 5.7, 5.7.1, 5.10, 6.1.2, 6.2, 6.2.1,

6.2.2, 6.2.3, 6.3, Chapter 7, Section 7.2, 7.3.1, 7.4, 7.4.1, 7.4.3, 7.4.5,

7.5, 7.5.3, 7.5.4, 7.5.5, 7.6, 7.7, 7.8, Chapter 8, Section 8.1, 8.1.1, 8.2,

8.2.1, 8.2.2, 8.2.3, 8.2.4, 8.2.5, 8.3, 8.4, Appendix 2.2, 3, 4

Addition

Product Configuration, Section 2.4, 2.5, 2.6, Appendix 1.2, Index

Deletion

Section 2.4

May, 2001 SH(NA)-080049-C Module addition

QJ71LP21G, QJ71LP21GE

Correction

Safety Precautions, Contents, About the Generic Terms and

Abbreviations, Section 1.1, 1.2, 2.4, 2.13, 2.1.4, 2.2, 2.2.1, 2.3, 3.1.1,

3.1.3, 3.2, 3.2.2, 3.3.2, 3.3.3, 3.3.4, 4.3.2, 4.4.2, 4.5.1, 4.5.2, 4.5.3,

4.6.2, 4.7.1, 4.7.2, Chapter 5, Section 5.1, 5.2.5, 5.2.6, 5.4, 5.6, 5.7.1,

5.7.2, 5.8, 5.9, 6.1.2, 6.2.1, 6.3, Chapter 7, Section 7.2, 7.3, 7.3.1,

7.4.1, 7.4.2, 7.4.5, 7.5, 7.9, 8.1.1, 8.1.4, 8.3, Appendix 2.1

Addition

Section 2.5

Section number changed

Section 2.5 2.6, 2.6 2.7

June, 2002 SH(NA)-080049-D Module addition

QJ71LP21S-25

Correction

Safety Precautions, Contents, About Manuals, Product Configuration,

Section 1.1, 1.2, 2.2, 3.1.1, 3.2.2, 3.3.2, 4.2, 5.2.1, 5.6, 6.2.1, 6.2.2,

Chapter 7, Section 7.3, 7.3.2, 7.4.5, 8.3, Appendix 3, 4, Index

Apr., 2003 SH(NA)-080049-E Correction

Safety Precautions, Contents, About Manuals, Section 1.2, 2.1.3, 2.2.2,

2.5, 3.1.1, 3.2.1, 3.2.2, 3.3.1, 3.3.3, Chapter 5, Section 5.2.1, 5.7, 5.7.1,

5.7.2, 5.8, 5.9, 6.1.2, 6.2, 6.4, 7.1, 7.4.2, 7.4.3, 7.4.4, 7.4.5, 7.5, 7.5.4,

7.8, 7.9, 8.1, 8.2, 8.2.1, 8.2.5, 8.3

A - 7 A - 7

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Jun., 2004 SH(NA)-080049-F · The contents of function version D were added.

· The entire manual was reviewed.

Oct., 2004 SH(NA)-080049-G Mode addition

MELSECNET/H Extended Mode

Correction

Safety Precautions, Product Configuration, Section 1.1, 1.2, 2.1.2, 2.2,

2.2.2, 2.2.3, 3.1.1, 3.2.1, 3.3.2, 4.2, 4.3.3, 4.6.1, 4.6.2, 4.8.1, Chapter 5,

Section 5.1, 5.4, 6.2.2, 6.2.3, 7.4.5, 7.6, 7.10.2, 8.1, 8.1.1, 8.1.2, 8.1.3,

8.2, 8.2.1, 8.2.7, 8.3, Appendix 1.1, 1.2, 3, 4, 5, INDEX

Addition

Section 8.2.5, 8.2.9, 8.2.10

Section number changed

Section 8.2.5 8.2.6, 8.2.6 8.2.7, 8.2.7 8.2.8

Oct., 2005 SH(NA)-080049-H Correction

Safety Precautions, Conformation to the EMC Directive and Low

Voltage Instruction, Section 1.1, 1.2, 2.1.2, 2.2, 2.2.1, 2.2.3, 3.1.3,

3.3.2, 4.2, 4.6.1, 4.7.1, 4.7.2, 4.8.1, Chapter 5, Section 5.1, 5.4,

Chapter 6, 7, Section 7.3.1, 7.7, 7.10.2, 8.1.2, 8.1.3, 8.2, 8.2.5, 8.3,

Appendix 1.1, 1.2, 3, 4, 5

Apr., 2006 SH(NA)-080049-I Correction

Section 2.3, 3.1.2, 4.2, 6.3, 7.4.5, Appendix 4

Oct., 2007 SH(NA)-080049-J Change of a term

"PLC" was changed to "programmable controller".

Correction

About the Generic Terms and Abbreviations, 1.2, 2.1.3, 2.1.4, 2.2, 2.3,

3.2.1, 3.3.2, 3.3.3, 4.2, 4.5.1, 4.5.2, 4.5.3, 4.6.1, 4.7.1, 4.7.2, Chapter 5,

5.1, 5.6, 5.7, 5.7.1, 5.7.2, 6.1.1, 6.2.2, 6.3, 6.4, 7.2, 7.4.5, 7.5.5, 7.10.2,

8.1, 8.2.1, 8.2.4, 8.3, Appendix 3, 4, 5

Addition

DEFINITIONS OF TERMINOLOGY

Jul., 2008 SH(NA)-080049-K Correction

SAFETY PRECAUTIONS, Compliance with the EMC and Low Voltage

Directives, About the Generic Terms and Abbreviations, DEFINITIONS

OF TERMINOLOGY, Chapter 1, Section 2.1, 2.2, 3.1.1, 3.1.3, 3.2,

3.3.2 to 3.3.4, 4.2, 4.3.4, 4.6.2, 4.7.1, 4.7.2, Chapter 5, Section 5.1, 5.4,

5.6 to 5.9, 6.1.1, 6.3, Chapter 7, Section 7.2, 7.3, 7.4.1, 7.4.2, 7.4.5,

7.5, 7.5.5, 7.7 to 7.9, 7.10.2, 7.10.5, 7.10.7, 8.1, 8.3, Appendix 1.1, 2.1,

3, 4

A - 8 A - 8

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Jan., 2009 SH(NA)-080049-L Mode addition

QJ71NT11B

Correction

SAFETY PRECAUTIONS, COMPLIANCE WITH THE EMC AND LOW

VOLTAGE DIRECTIVES, GENERIC TERMS AND ABBREVIATIONS,

PACKING LIST, Section 1.1 to 1.3, 2.1.1, 2.1.2, 2.1.4, 2.2, 2.2.3,

3.1.1 to 3.1.3, 3.2.2, 3.3.2, 3.3.3, 4.1 to 4.3, 4.5, 4.5.1 to 4.5.3, 4.7.1,

4.7.2, 4.8, 4.8.2, Chapter 5, Section 5.1, 5.2.5, 5.4, 5.7.1, 6.1.1, 6.4,

7.1 to 7.3, 7.4.1, 7.4.2, 7.4.5, 7.5.5, 7.9, 7.10.2, 8.2, 8.2.1 to 8.2.4, 8.3,

8.4, Appendix 1.1, 1.2, 3, 4, INDEX

Addition

Section 3.1.4, 3.1.5, 4.2.1 to 4.2.3, 4.6.3, 4.6.4, 5.2.6, 8.2.6,

Appendix 5

Section number changed

Section 4.3.3 4.3.2, 4.3.4 4.3.3, 4.3.5 4.3.4, 5.2.6 5.2.7,

8.2.6 8.2.7, 8.2.7 8.2.8, 8.2.8 8.2.9, 8.2.9 8.2.10,

8.2.10 8.2.11, Appendix 5 6

Aug., 2009 SH(NA)-080049-M Correction

Section 1.3, 2.2, 2.3, Chapter 8, Appendix 1.2

Addition

Section 8.3.1

Section number changed

Section 8.3(4) 8.3.2

Sep., 2010 SH(NA)-080049-N Correction

GENERIC TERMS AND ABBREVIATIONS, Section 1.3, 2.2.1, 2.3,

4.2.1, 4.2.2, 4.2.3, 4.3.1, 5.8, 6.4, 7.4.5, 7.5.6, 8.2.4, 8.2.8, 8.2.10,

8.3.2, Appendix 4, 6

Addition

CONDITIONS OF USE FOR THE PRODUCT

May, 2012 SH(NA)-080049-O Correction

SAFETY PRECAUTIONS, COMPLIANCE WITH THE EMC AND LOW

VOLTAGE DIRECTIVES, GENERIC TERMS AND ABBREVIATIONS,

Section 2.2, 2.3, 3.1.3, 3.1.4, 3.2.2, 3.3.1, 4.2.1, 4.6.2, 5.7, 6.1.1, 6.3,

7.4.5, 7.10.2, 8.3.2, Appendix 3, 6

Otros manuales para Melsec QJ71LP21

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric PAC-YT51CRB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric CR750 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX3G SERIES Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MEHITS CH Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Artisan MELSEC-Q Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CC-Link IE Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PAC-IF031B-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R16MTCPU Manual del propietario

Mitsubishi Electric

Mitsubishi Electric Q170MSCPU Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FA-LTB40ADG Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric melsec q26ud(e)hcpu Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R C Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX2N-20GM Manual de usuario

Mitsubishi Electric

Mitsubishi Electric RD77GF8 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC-L02SCPU Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GB-24A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC-A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q172CPU Manual del propietario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5U Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC FX Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric a2 Series Manual del propietario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario