Mitsubishi Electric MELSEC-A Series Manual de usuario

Type A1SJHCPU

Mitsubishi Programmable Controller

User's Manual

(Hardware)

Thank you for purchasing the Mitsubishi programmable controller

MELSEC-A series.

Prior to use, please read both this and relevant manuals

thoroughly to fully understand the product.

MODEL A1SJCPU(H/W)-U-E

MODEL

CODE 13JE60

IB(NA)-66469-L(0810)MEE

A-1

zSAFETY PRECAUTIONS z

(Be sure to read these instructions before use.)

Before using the product, read this and relevant manuals carefully and handle the

product correctly with full attention to safety.

In this manual, zSAFETY PRECAUTIONS zare classified into 2 levels:

"DANGER" and "CAUTION".

Indicates that incorrect handling may cause hazardous

conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous

conditions, resulting in minor or moderate injury and/or

property damage.

Under some circumstances, failure to observe the CAUTION level

instructions may also lead to serious results.

Be sure to observe the instructions of both levels to ensure the safety.

Please keep this manual in a safe place for future reference and also pass this

manual on to the end user.

[DESIGN PRECAUTIONS]

DANGER

zCreate a safety circuit outside the programmable controller to ensure the

whole system will operate safely even if an external power failure or a

programmable controller failure occurs.

Otherwise, incorrect output or malfunction may cause an accident.

(1) For an emergency stop circuit, protection circuit and interlock circuit that

is designed for incompatible actions such as forward/reverse rotation or

for damage prevention such as the upper/lower limit setting in

positioning, any of them must be created outside the programmable

controller.

Install the emergency stop switch outsid the controlpanel so that workers

can operate it easily.

DANGER

CAUTION

A-2

[DESIGN PRECAUTIONS]

DANGER

(2) When the programmable controller detects the following error

conditions, it stops the operation and turn off all the outputs.

yThe overcurrent protection device or overvoltage protection device of

the power supply module is activated.

yThe programmable controller CPU detects an error such as a

watchdog timer error by the self-diagnostics function.

In the case of an error of a part such as an I/O control part that cannot

be detected by the programmable controller CPU, all the outputs may

turn on. In order to make all machines operate safely in such a case, set

up a fail-safe circuit or a specific mechanism outside the programmable

controller.

Refer to "LOADING AND INSTALLATION" in this manual for example

fail safe circuits.

(3) Depending on the failure of the output module’s relay or transistor, the

output status may remain ON or OFF incorrectly. For output signals that

may lead to a serious accident, create an external monitoring circuit.

yIf load current more than the rating or overcurrent due to a short circuit

in the load has flowed in the output module for a long time, it may

cause a fire and smoke. Provide an external safety device such as a

fuse.

yDesign a circuit so that the external power will be supplied after

power-up of the programmable controller.

Activating the external power supply prior to the programmable

controller may result in an accident due to incorrect output or

malfunction.

yFor the operation status of each station at a communication error in

data link, refer to the respective data link manual.

The communication error may result in an accident due to incorrect

output or malfunction.

A-3

[DESIGN PRECAUTIONS]

DANGER

zWhen controlling a running programmable controller (data modification) by

connecting a peripheral device to the CPU module or a PC to a special

function module, create an interlock circuit on sequence programs so that the

whole system functions safely all the time.

Also, before performing any other controls (e.g. program modification,

operating status change (status control)), read the manual carefully and

ensure the safety.

In these controls, especially the one from an external device to a

programmable controller in a remote location, some programmable controller

side problem may not be resolved immediately due to failure of data

communications.

To prevent this, create an interlock circuit on sequence programs and

establish corrective procedures for communication failure between the

external device and the programmable controller CPU.

zWhen setting up the system, do not allow any empty slot on the base unit.

If any slot is left empty, be sure to use a blank cover (A1SG60) or a dummy

module (A1SG62) for it.

When using the extension base unit, A1S52B, A1S55B or A1S58B, attach

the included dustproof cover to the module in slot 0.

Otherwise, internal parts of the module may be flied in the short circuit test or

when an overcurrent or overvoltage is accidentally applied to external I/O

section.

CAUTION

zDo not install the control lines or communication cables together with the

main circuit or power lines, or bring them close to each other.

Keep a distance of 100mm (3.94inch) or more between them.

Failure to do so may cause malfunctions due to noise.

zWhen an output module is used to control the lamp load, heater, solenoid

valve, etc., a large current (ten times larger than the normal one) may flow at

the time that the output status changes from OFF to ON. Take some

preventive measures such as replacing the output module with the one of a

suitable current rating.

A-4

[INSTALLATION PRECAUTIONS]

CAUTION

zUse the programmable controller under the environment specified in the

user’s manual.

Otherwise, it may cause electric shocks, fires, malfunctions, product

deterioration or damage.

zInsert the module fixing projection into the fixing hole in the base unit and

then tighten the module mounting screw within the specified torque.

When no screw is tightened, even if the module is installed correctly, it may

cause malfunctions, a failure or a drop of the module.

Tightening the screw excessively may damage the screw and/or the module,

resulting in a drop of the module, a short circuit or malfunctions.

zConnect the extension cable to the connector of the base unit or module.

Check the cable for incomplete connection after connecting it.

Poor electrical contact may cause incorrect inputs and/or outputs.

zInsert the memory card and fully press it to the memory card connector.

Check for incomplete connection after installing it.

Poor electrical contact may cause malfunctions.

zBe sure to shut off all phases of the external power supply used by the

system before mounting or removing the module. Failure to do so may

damage the module.

zDo not directly touch the conductive part or electronic components of the

module.

Doing so may cause malfunctions or a failure of the module.

A-5

[WIRING PRECAUTIONS]

DANGER

zBe sure to shut off all phases of the external power supply used by the

system before wiring.

Failure to do so may result in an electric shock or damage of the product.

zBefore energizing and operating the system after wiring, be sure to attach the

terminal cover supplied with the product.

Failure to do so may cause an electric shock.

CAUTION

zAlways ground the FG and LG terminals to the protective ground conductor.

Failure to do so may cause an electric shock or malfunctions.

zWire the module correctly after confirming the rated voltage and terminal

layout.

Connecting a power supply of a different voltage rating or incorrect wiring

may cause a fire or failure.

zDo not connect multiple power supply modules to one module in parallel.

The power supply modules may be heated, resulting in a fire or failure.

zPress, crimp or properly solder the connector for external connection with the

specified tool.

Incomplete connection may cause a short circuit, fire or malfunctions.

zTighten terminal screws within the specified torque range. If the screw is too

loose, it may cause a short circuit, fire or malfunctions.

If too tight, it may damage the screw and/or the module, resulting in a short

circuit or malfunctions.

zCarefully prevent foreign matter such as dust or wire chips from entering the

module.

Failure to do so may cause a fire, failure or malfunctions.

zInstall our programmable controller in a control panel for use.

Wire the main power supply to the power supply module installed in a control

panel through a distribution terminal block.

Furthermore, the wiring and replacement of a power supply module have to

be performed by a maintenance worker who acquainted with shock

protection.

(For the wiring methods, refer to Type A1SJH(S8)/A1SH/A2SHCPU(S1)

User’s Manual)

A-6

[STARTUP AND MAINTENANCE PRECAUTIONS]

DANGER

zDo not touch any terminal during power distribution.

Doing so may cause an electric shock.

zProperly connect batteries. Do not charge, disassemble, heat or throw them

into the fire and do not make them short-circuited and soldered. Incorrect

battery handling may cause personal injuries or a fire due to exothermic heat,

burst and/or ignition.

zBe sure to shut off all phases of the external power supply used by the

system before cleaning or retightening the terminal screws or module

mounting screws.

Failure to do so may result in an electric shock.

If they are too loose, it may cause a short circuit or malfunctions.

If too tight, it may cause damage to the screws and/or module, resulting in an

accidental drop of the module, short circuit or malfunctions.

CAUTION

zWhen performing online operations (especially, program modification, forced

output or operating status change) by connecting a peripheral device to the

running CPU module, read the manual carefully and ensure the safety.

Incorrect operation will cause mechanical damage or accidents.

zDo not disassemble or modify each of modules.

Doing so may cause failure, malfunctions, personal injuries and/or a fire.

zWhen using a wireless communication device such as a mobile phone, keep

a distance of 25cm (9.84inch) or more from the programmable controller in

all directions.

Failure to do so may cause malfunctions.

zBe sure to shut off all phases of the external power supply used by the

system before mounting or removing the module.

Failure to do so may result in failure or malfunctions of the module.

zDo not drop or apply any impact to the battery.

Doing so may damage the battery, resulting in electrolyte spillage inside the

battery.

If any impact has been applied, discard the battery and never use it.

zBefore handling modules, touch a grounded metal object to discharge the

static electricity from the human body.

Failure to do so may cause failure or malfunctions of the module.

A-7

[DISPOSAL PRECAUTIONS]

CAUTION

zWhen disposing of the product, treat it as an industrial waste.

When disposing of batteries, separate them from other wastes according to

the local regulations.

(For details of the battery directive in EU member states, refer to the

A1SJH/A1SH/A2SHCPU(S1) User’s manual.)

[TRANSPORTATION PRECAUTIONS]

CAUTION

zWhen transporting lithium batteries, make sure to treat them based on the

transportation regulations. (Refer to Appendix 2 for details of the relevant

models.)

A-8

REVISIONS

*The manual number is given on the bottom right of the front cover.

Print Date *Manual Number Revision

Mar., 1994 IB(NA) 66469-A First edition

Oct., 1995 IB(NA) 66469-B

Jan., 1996 IB(NA) 66469-C

Jun., 1997 IB(NA) 66469-D

Sep., 1998 IB(NA) 66469-E Correction

Safety precautions, Chapter1, Chapter2,

Chapter3, Chapter4, Chapter5

Deletion

Notification of CE marking, Chapter6,

Chapter7, Appendix

Jan., 2003 IB(NA) 66469-F Equivalent to Japanese version J

Partial additions

5.1, 5.2

Partial corrections

Safety precautions, 1.1, 3, 4.2, 4.4, 4.5.1,

4.5.2, 6.1.1

Jun., 2003 IB(NA) 66469-G Partial corrections

Safety precautions, Section 6.1.1

Addition

Appendix 2

Dec., 2003 IB(NA) 66469-H Addition of model

A1SY42P

Partial corrections

Section 3.1.4, 4.2, 5.2.1, 5.2.2

Jun., 2006 IB(NA) 66469-I Partial corrections

Safety precautions, Section 2.1, Chapter3,

Section 3.1, 3.1.3, 3.2, 3.2.1, 4.4, 4.5.1,

4.5.2, 6.1.1

Addition

USER PRECAUTIONS, Section 4.5.3

Otros manuales para MELSEC-A Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric PAC-ZC40L-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric City Multi PAC-LV11M-J Manual de usuario

Mitsubishi Electric

Mitsubishi Electric NZ2GF-CCB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric ME1PB1-L Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC-L Series LD40PD01 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX3U-J1939 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R RD78G4 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric NZ2GN2B1-32D Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric BRANCH BOX PAC-MKA53BC Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric GB-24A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Melsec QJ71NT11B Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q172CPU Manual del propietario

Mitsubishi Electric

Mitsubishi Electric PAC-YT34STA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC FX Series Manual del propietario

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric QE82LG Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX3U-2HSY-ADP Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de servicio

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario