Mitsubishi Electric MELSEC-A Series Manual de usuario

CC-Link System RS-232 Interface Module

User's Manual (MELSOFT Connection Mode)

A- 1

SAFETY PRECAUTIONS

(Always read these instructions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual

carefully and pay full attention to safety to handle the product correctly.

The instructions given in this manual are concerned with this product only. For the safety instructions of the

programmable controller system, please read the user's manual for the CPU module used.

In this manual, the safety precautions are classified into two levels: "WARNING" and "CAUTION".

Note that the CAUTION level may lead to a serious consequence according to the circumstances.

Always follow the instructions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

[Design Precautions]

WARNING

●When controlling a running programmable controller (data modification) by connecting a peripheral

to a CPU module or connecting a personal computer to an intelligent/special function module, create

an interlock circuit on the sequence program so that the whole system will operate safely all the time.

Also, before performing other controls (e.g. program modification, operating status change (status

control)), read this manual carefully and ensure the safety.

Especially, in the control from an external device to a programmable controller in a remote location,

some programmable-controller-side problems cannot be resolved immediately due to a data

communication failure.

To prevent this, establish corrective procedures for communication failure between the external

device and the programmable controller CPU, as well as creating an interlock circuit on the

sequence program.

●In the case of a data link error, the operation status of a faulty station is as shown below. Using the

communication status information, create an interlock circuit on the sequence program for the

system to operate safely.

Incorrect output or malfunction can lead to an accident.

(1) All of general-purpose inputs from this module turn OFF.

(2) All of general-purpose outputs from this module turn OFF.

●Depending on the module failure, inputs and outputs may turn ON or OFF incorrectly.

For I/O signals that may cause a serious accident, provide an external monitoring circuit.

WARNING

CAUTION

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

A- 2

[Installation Precautions]

CAUTION

●Do not bunch the control wires or communication cables with the main circuit or power wires, or

install them close to each other.

They should be installed 100 mm (3.94 inch) or more from each other.

Not doing so could result in noise that would cause erroneous operation.

●Always use the data link terminal block for connection of a CC-Link dedicated cable to a master

module.

Care must be taken because, if the cable is incorrectly inserted into the general-purpose I/O terminal

block instead of the data link terminal block, the module will break down.

CAUTION

●Use the programmable controller in an environment that meets the general specifications given in

this manual.

Using this programmable controller in an environment outside the range of the general specifications

could result in electric shock, fire, erroneous operation, and damage to or deterioration of the

product.

●Using a tool specified by the manufacturer, correctly press, crimp, or solder the wires of the

connector and securely connect the connector to the module.

Incomplete connection may cause a short circuit and/or malfunctions.

●Do not directly touch the module's conductive parts or electronic components.

Touching the conductive parts could cause an operation failure or give damage to the module.

●Securely fix the module with the DIN rail or installation screws. Installation screws must be tightened

within the specified torque range.

A loose screw may cause a drop of the module, short circuit or malfunction.

Overtightening may damage the screw, resulting in a drop of the module or a short circuit.

●Completely connect each cable connector to each receptacle.

Incomplete connection may cause a malfunction due to poor contact.

A- 3

[Wiring Precautions]

CAUTION

●Be sure to shut off all phases of the external power supply used by the system before installation or

wiring.

Failure to do so may cause an electric shock, damage to the product and/or malfunctions.

●Attach the terminal cover to the product before energizing and operating the system after installation

or wiring.

Failure to do so may cause an electric shock.

●Be sure to ground the FG terminals and LG terminals to the protective ground conductor.

Failure to do so may result in malfunctions.

A- 4

[Wiring Precautions]

CAUTION

●Use applicable solderless terminals and tighten them within the specified torque range. If any spade

solderless terminal is used, it may be disconnected when a terminal block screw comes loose,

resulting in failure.

●When wiring in the programmable controller, be sure that it is done correctly by checking the

product's rated voltage and the terminal layout.

Connecting a power supply that is different from the rating or incorrectly wiring the product could

result in fire or damage.

●Tighten the terminal screws with the specified torque.

If the terminal screws are loose, it could result in short circuits, fire, or erroneous operation.

Overtightening a terminal screw may damage the screw, resulting in a short circuit or malfunction.

●Be sure there are no foreign substances such as sawdust or wiring debris inside the module.

Such debris could cause fires, damage, or erroneous operation.

●Place the connection wires and cables in a duct or clamp them.

If not, dangling cables may swing or inadvertently be pulled, resulting in damage to the module and/

or cables or malfunctions due to poor cable connection.

●Do not install the control cable(s) together with the communication cable(s).

Doing so may cause malfunctions due to noise.

●When disconnecting a communication or power cable from the module, do not pull it by holding the

cable part.

For a cable with connector, hold the connector and disconnect it from the module.

For a cable without connector, loosen the connector screw and disconnect the cable.

Pulling the cable that is still connected to the module may damage the module and/or cable and

cause malfunctions due to poor cable connection.

●Make sure that the interface type is correct before connecting the cable.

Do not connect a cable to a module that has different interface specification.

Doing so will cause a module failure.

●Using a tool specified by the manufacturer, correctly press, crimp, or solder the wires of the

connector and securely connect the connector to the module.

Failure to do so may result in a malfunction or failure of the module.

A- 5

[Startup·Maintenance Precautions]

CAUTION

●Before performing online operations (especially, program modification, forced output or operating

status change) through connection between a running CPU module and a peripheral, read this

manual carefully and ensure the safety.

An improper operation will cause mechanical damage or accidents.

●Do not touch terminals while the power is ON.

Doing so may cause an electric shock.

●Be sure to shut off all phases of the external power supply used by the system before cleaning or

retightening the terminal screw or module fixing screw.

Failure to do so may result in a failure or malfunction of the module.

A loose screw may cause a drop of the module, short circuit or malfunction.

Overtightening may damage the screw and/or module, resulting in a drop of the module, a short

circuit or malfunctions.

●Do not touch any connector under the cover on the front of the module.

Doing so may result in a failure or malfunction of the module.

●Do not disassemble or remodel the module.

Doing so may cause a failure, malfunctions, personal injuries and/or a fire.

●Do not drop or apply a strong shock to the module since the case is made of resin.

Doing so will damage the module.

●Be sure to shut off all phases of the external power supply before mounting or removing the module

to/from the panel.

Failure to do so may result in a failure or malfunction of the module.

●Do not install/remove the terminal block more than 50 times after the first use of the product.

(IEC 61131-2 compliant)

●Before handling the module, touch a conducting object such as a grounded metal to discharge the

static electricity from the human body.

Failure to do so may cause the module to fail or malfunction.

●Do not change the switch settings while the power is ON.

Doing so may cause a failure or malfunctions.

●The terminal cover must be closed all the time, except during installation, wiring or operation check.

If the cover remains open, it may cause damage to the module, a short circuit due to cable

connection failure, or malfunctions.

A- 6

[Disposal Precautions]

CAUTION

●When disposing of this product, treat it as industrial waste.

A- 7

CONDITIONS OF USE FOR THE PRODUCT

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major

or serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of

the PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT

LIMITED TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT,

WARRANTY, TORT, PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR

LOSS OR DAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR

USED IN APPLICATION NOT INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS,

OR WARNING CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY

MANUALS, TECHNICAL BULLETINS AND GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

• Nuclear Power Plants and any other power plants operated by Power companies, and/or any

other cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

• Railway companies or Public service purposes, and/or any other cases in which establishment of

a special quality assurance system is required by the Purchaser or End User.

• Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as

Elevator and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation,

Equipment for Recreation and Amusement, and Safety devices, handling of Nuclear or

Hazardous Materials or Chemicals, Mining and Drilling, and/or other applications where there is a

significant risk of injury to the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT

is limited only for the specific applications agreed to by Mitsubishi and provided further that no

special quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

A- 8

REVISIONS

* The manual number is given on the bottom left of the back cover.

Japanese Manual Version SH-080686-E

2007 MITSUBISHI ELECTRIC CORPORATION

Print Date * Manual Number Revision

Jul., 2007 SH(NA)-080687ENG-A First edition

Sep., 2008 SH(NA)-080687ENG-B

SAFETY PRECAUTIONS, ABOUT MANUALS, Compliance with the EMC and

Low Voltage Directives, GENERIC TERMS AND ABBREVIATIONS, Section 2.2,

2.3, 3.2, 3.5.1, 4.2.1, 5.1.1, 5.2, 6.1.3, 6.2.3

Section 2.4

Oct., 2014 SH(NA)-080687ENG-C

SAFETY PRECAUTIONS, Related manuals, Compliance with the EMC and Low

Voltage Directives, HOW TO USE MANUALS, GENERIC TERMS AND

ABBREVIATION, DEFINITIONS OF TERMINOLOGY, Chapter 1, Section 1.1,

2.1 to 2.3, 3.1 to 3.4, 3.5.1, 3.7.1, 3.7.3, 4.1, 4.2, 4.2.1, 5.1.1, 5.2, 5.4, Chapter 6,

Section 6.1, Chapter 7, Section 7.1, Appendix 1.1, 1.2

Section 2.5, 6.1, Appendix 3

Section 6.1→6.2, Section 6.2→6.3

Jan., 2020 SH(NA)-080687ENG-D

Section 5.2, 7.1

This manual confers no industrial property rights or any rights of any other kinds, nor does it confer any patent licenses.

Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may

occur as a result of using the contents noted in this manual.

Partially revised

Added

Partially revised

Added

Change

Partially revised

Otros manuales para MELSEC-A Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric FX3G-2AD-BD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AE-200A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric RD77MS2 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R C Series Manual del propietario

Mitsubishi Electric

Mitsubishi Electric NZ2MF2S2-16A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Melsec WS Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PAC-YT51CRB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX2N-10PG Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC System Q Manual del propietario

Mitsubishi Electric

Mitsubishi Electric MELSEC L series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSERVO-JET MR-JET-G-N1 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric QD62 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CR750 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC FX2N-16SW Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX3G SERIES Manual del propietario

Mitsubishi Electric

Mitsubishi Electric MELSEC FX2N-4da Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric NZ2GFCE-60DAV8 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX2NC-16EX-DS Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX2N-10GM Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PAC-SE51CRA Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario