Mitsubishi Electric FX2N-485-BD Manual de usuario

FX2N-485-BD COMMUNICATION BOARD

USER'S MANUAL

HEAD OFFICE: MITSUBISHI DENKI BLDG MARUNOUCHI TOKYO 100 TELEX: J24532 CABLE MELCO TOKYO

HIMEJI WORKS: 840, CHIYODA CHO, HIMEJI, JAPAN

-485-BD COMMUNICATION BOARD

USER'S MANUAL

JY992D66201A

(MEE 9706) Effective JUN. 1997

Specifications are subject

to change without notice.

-485-BD COMMUNICATION BOARD

Foreword

•This manual containstext, diagrams and explanations which will guide the reader in thecorrect installation and operation

of the FX2N-485-BD COMMUNICATION BOARD. It should be read and understood before attempting to install or use the

unit.

Further information can be found in the FX PROGRAMMING MANUAL, FX2N series hardware manuals and manual of

FX-485PC-IF USER’S MANUAL.

•If in doubt at any stage during the installation of the FX2N-485-BD COMMUNICATION BOARD always consult a

professional electrical engineer who is qualified and trained to the local and national standards.

-485-BD COMMUNICATION BOARD

Under no circumstances will MITSUBISHI ELECTRIC be liable responsible for any consequential damage that may arise

as a result of the installation or use of this equipment.

All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee

operation. MITSUBISHI ELECTRIC will accept no responsibility for actual use of the product based on these illustrative

examples.

Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for

your specific application.

-485-BD COMMUNICATION BOARD

USER’S MANUAL

FX2N-485-BD COMMUNICATION BOARD

Manual number: JY992D66201

Manual revision: A

Date: JUNE 1997

-485-BD COMMUNICATION BOARD

Guidelines for the safety of the user and protection of the FX2N-485-BD COMMUNICATION BOARD.

This manual provides information for the installation and use of the FX2N-485-BD COMMUNICATION BOARD. The manual

has been written to be used by trained and competent personnel. The definition of such a person or persons is as follows;

a) Any engineer who is responsible for the planning, design and construction of automatic equipment using the product

associated with this manual should be of a competent nature, (trained and qualified to the local and national standards

required to fulfill that role). These engineers should be fully aware of safety with regards to automated equipment.

b) Any commissioning or service engineer must be of a competent nature, trained and qualified to the local and national

standards required to fulfill that job. These engineers should also be trained in the use and maintenance of the

completed product. This includes being completely familiar with all associated documentation for the said product. All

maintenance should be carried out in accordance with established safety practices.

c) All operators of the compliance product should be trained to use that product in a safe and coordinated manner in

compliance to established safety practices. The operators should also be familiar with all documentation which is

connected with the actual operation of the completed equipment.

Note: The term ‘completed equipment’ refers to a third party constructed device which contains or uses the product

associated with this manual.

-485-BD COMMUNICATION BOARD

Note’s on the symbology used in this manual

At various times through out this manual certain symbols will be used to highlight points of information which are intended to

ensure the users personal safety and protect the integrity of the equipment. Whenever any of the following symbols are

encountered, its associated note must be read and understood. Each of the symbols used will now be listed with a brief

description of its meaning.

Hardware warnings

1) Indicates that the identified danger WILL cause physical and property damage.

2) Indicates that the identified danger POSSIBLY cause physical and property damage.

3) Indicates a point of further interest or further explanation.

Software warnings

4) Indicates special care must be taken when using this element of software.

5) Indicates a special point of which the user of the associate software element should be aware.

6) Indicates a point of interest or further explanation.

-485-BD COMMUNICATION BOARD

iii

CONTENTS
INTRODUCTION ..................................... 1-1
1 External Dimensions .................................. 1-2
2 System Configuration .................................. 1-3
2.1 When Use No Protocol or Dedicated Protocol ..................... 1-3
2.2 When Use Parallel Link ................................ 1-3
2.3 When Use N:N Network ................................ 1-4
MOUNTING AND WIRING ................................ 2-1
1 Mounting Procedure ................................... 2-1
2 Cable and Terminal Resistor .............................. 2-2
2.1 Cable .......................................... 2-2
2.2 Selection of Wiring ................................... 2-3
2.3 Terminal Resistor ................................... 2-4
2.4 Two-pair Wiring .................................... 2-5
2.5 One-pair Wiring .................................... 2-6
SPECIFICATION ..................................... 3-1
1 General Specification .................................. 3-1
2 Power Supply Specification ............................... 3-1
3 Specification ....................................... 3-1
COMMUNICATION FORMAT ............................... 4-1
1 Related Flag and Data Registers ............................ 4-1
2 Communication Format D8120 ............................. 4-2
2.1 Example Program of Setting .............................. 4-4
FX
2N
-485-BD COMMUNICATION BOARD
iv

RS EXAMPLE PROGRAM ................................5-1
1 Printer ..........................................5-1
1.1 System Configuration ..................................5-1
1.2 Communication Format .................................5-2
1.3 Example Program (1) ..................................5-3
2 Personal Computer ...................................5-4
2.1 System Configuration ..................................5-4
2.2 Communication Format .................................5-5
2.3 Example Program (2) ..................................5-6
PARALLEL LINK ......................................6-1
1 Parallel Link .......................................6-1
2 Outline ..........................................6-1
2.1 Normal Mode (Special auxiliary relay M8162: OFF) ..................6-2
2.2 High Speed Mode (Special auxiliary relay M8162: ON) ................6-2
3 Example Program (3) ..................................6-3
3.1 Normal Mode ......................................6-3
3.2 High Speed Mode ...................................6-4
N:N NETWORK ......................................7-1
1 Outline ..........................................7-1
2 Related Flags and Data Registers ............................7-2
2.1 Special Auxiliary Relays ................................7-2
2.2 Special Data Registers .................................7-3
3 Setting ..........................................7-4
FX
2N
-485-BD COMMUNICATION BOARD
v

Tabla de contenidos

Otros manuales de Controladores de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric FX2NC-16EX-DS Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC FX3U-232ADP Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q Series Manual del propietario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric L26CPU-BT Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manual del propietario

Mitsubishi Electric

Mitsubishi Electric NZ2MF2S2-16A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC FX3U-485ADP-MB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PAR-40MAAU Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC-A Manual

Mitsubishi Electric

Mitsubishi Electric NZ2GF2BN-60DA4 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX3S-10M series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric NZ2GFCE-60DAV8 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric QD70D4 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q12DCCPU-V Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-RD77MS2 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q Series Manual del propietario

Mitsubishi Electric

Mitsubishi Electric MELSEC FX3U-232ADP-MB Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario