Mitsubishi Electric Mr.Slim PEAD-RP35JALQ Manual de usuario

SERVICE MANUAL

Models PEAD-RP35JA(L)Q

PEAD-RP50JA(L)Q

PEAD-RP60JA(L)Q

PEAD-RP71JA(L)Q

PEAD-RP100JA(L)Q

PEAD-RP125JA(L)Q

PEAD-RP140JA(L)Q

1. SAFETY PRECAUTION ····························· 2

2. PART NAMES AND FUNCTIONS·············· 3

3. SPECIFICATION ········································ 5

4. FAN PERFORMANCE AND

CORRECTED AIR FLOW ·························· 8

5. SOUND PRESSURE LEVELS ···················15

6. OUTLINES & DIMENSIONS ······················22

7. WIRING DIAGRAM ····································24

8. REFRIGERANT SYSTEM DIAGRAM ········25

9. TROUBLESHOOTING ·······························26

. DISASSEMBLY PROCEDURE ··················40

CONTENTS

INDOOR UNIT

REMOTE CONTROLLER (option)

ON/OFF

TEMP.

Series PEAD

R410A

2010

SPLIT-TYPE, HEAT PUMP

AIR CONDITIONERS

NOTE:

•This manual describes only

service data of the indoor

units.

SAFETY PRECAUTION

1-1. ALWAYS OBSERVE FOR SAFETY

Cautions for units utilising refrigerant R410A

Use new refrigerant pipes.

Make sure that the inside and outside of refrige-

rant piping is clean and it has no contamination

such as sulfur hazardous for use, oxides, dirt,

shaving particles, etc.

In addition, use pipes with specified thickness.

Store the piping to be used indoors during

installation and both ends of the piping sealed

until just before brazing. (Leave elbow joints, etc.

in their packaging.)

Use ester oil, ether oil or alkylbenzene oil (small

amount) as the refrigerant oil applied to flares

and flange connections.

In case of using the existing pipes for R22, be careful with

the followings.

·For RP100, 125 and 140, be sure to perform replace-

ment operation before test run.

·Change flare nut to the one provided with this product.

Use a newly flared pipe.

·Avoid using thin pipes.

Charge refrigerant from liquid phase of gas

cylinder.

If the refrigerant is charged from gas phase, composition

change may occur in refrigerant and the efficiency will be

lowered.

Do not use refrigerant other than R410A.

If other refrigerant (R22 etc.) is used, chlorine in refrige-

rant can cause deterioration of refrigerant oil etc.

Use a vacuum pump with a reverse flow check

valve.

Vacuum pump oil may flow back into refrigerant cycle and

that can cause deterioration of refrigerant oil etc.

Use the following tools specifically designed for

use with R410A refrigerant.

The following tools are necessary to use R410A refrigerant.

Handle tools with care.

If dirt, dust or moisture enters into refrigerant cycle, that can

cause deterioration of refrigerant oil or malfunction of com-

pressor.

Do not use a charging cylinder.

If a charging cylinder is used, the composition of refrigera-

nt will change and the efficiency will be lowered.

Flare tool

Electronic refrigerant

charging scale

Vacuum pump adaptor

Size adjustment gauge

Gauge manifold

Torque wrench

Gas leak detector

Charge hose

Tools for R410A

Contamination inside refrigerant piping can cause deterio-

ration of refrigerant oil etc.

If dirt, dust or moisture enters into refrigerant cycle, that can

cause deterioration of refrigerant oil or malfunction of com-

pressor.

If large amount of mineral oil enters, that can cause deterio-

ration of refrigerant oil etc.

Ventilate the room if refrigerant leaks during

operation. If refrigerant comes into contact with

a flame, poisonous gases will be released.

[1] Cautions for service

(1) Perform service after recovering the refrigerant left in unit completely.

(2) Do not release refrigerant in the air.

(3) After completing service, charge the cycle with specified amount of refrigerant.

(4) When performing service, install a filter drier simultaneously.

Be sure to use a filter drier for new refrigerant.

[2] Additional refrigerant charge

When charging directly from cylinder

·Check that cylinder for R410A on the market is syphon type.

·Charging should be performed with the cylinder of syphon stood vertically. (Refrigerant is charged from liquid phase.)

Before obtaining access to terminal, all supply

circuits must be disconnected.

1-2. CAUTIONS RELATED TO NEW REFRIGERANT

Gravimeter

Unit

[3] Service tools

Use the below service tools as exclusive tools for R410A refrigerant.

No. Tool name Specifications

1Gauge manifold ·Only for R410A

·Use the existing fitting specifications. (UNF1/2)

·Use high-tension side pressure of 5.3MPa·G or over.

2Charge hose ·Only for R410A

·Use pressure performance of 5.09MPa·G or over.

3Electronic scale

4Gas leak detector ·Use the detector for R134a, R407C or R410A.

5Adaptor for reverse flow check ·Attach on vacuum pump.

6Refrigerant charge base

7Refrigerant cylinder ·Only for R410A ·Top of cylinder (Pink)

·Cylinder with syphon

8Refrigerant recovery equipment

PART NAMES AND FUNCTIONS

•Indoor Unit

Air intake (sucks the

air inside the room

into the unit)

In case of rear inlet

Air outlet

In case of bottom inlet

°F°C

ERROR CODE

AFTER

TIMER

TIME SUN MON TUE WED THU FRI SAT

OFF

AFTER

FILTER

FUNCTION

ONLY1Hr.

WEEKLY

SIMPLE

AUTO OFF

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

Display Section

For purposes of this explanation,

all parts of the display are shown

as lit. During actual operation, only

the relevant items will be lit.

Identifies the current operation

Shows the operating mode, etc.

*Multilanguage display is available.

“Centrally Controlled” indicator

Indicates that operation from the

remote controller has been prohib-

ited by a master controller.

“Timer is Off” indicator

Indicates that the timer is off.

Temperature Setting

Shows the target temperature.

Day-of-Week

Shows the current day of the week.

Time/Timer Display

Shows the current time, unless the simple or Auto Off

timer is set.

If the simple or Auto Off timer is set, the time to be

switched off is shown.

“Sensor” indication

Displayed when the remote controller

sensor is used.

“Locked” indicator

Indicates that remote controller but-

tons have been locked.

“Clean The Filter” indicator

To be displayed on when it is time to

clean the filter.

Timer indicators

The indicator comes on if the corre-

sponding timer is set.

Up/Down Air Direction indica-

tor

The indicator shows the direc-

tion of the outcoming airflow.

“One Hour Only” indicator

Room Temperature display

Shows the room temperature. The room

temperature display range is 8–39˚C.

The display blinks if the temperature

is less than 8˚C or 39˚C or more.

Louver display

Indicates the action of the swing louver.

Does not appear if the louver is not

running.

(Power On indicator)

Indicates that the power is on.

Fan Speed indicator

Shows the selected fan speed.

Ventilation indicator

Appears when the unit is running in

Ventilation mode.

Operation Section

Temperature setting buttons

Down

Timer Menu button

(Monitor/Set button)

Mode button (Return button)

Set Time buttons

Back

Ahead

Timer On/Off button

(Set Day button)

Opening the

lid

ON/OFF button

Fan Speed button

Filter button

(<Enter> button)

Test Run button

Check button (Clear button)

Airflow Up/Down button

Louver button

( Operation button)

To return operation

number

Ventilation button

( Operation button)

To go to next operation

number

Note:

“PLEASE WAIT” message

This message is displayed for approximately 3 minutes when power is supplied to the indoor unit or when the unit is recovering from a power failure.

“NOTAVAILABLE” message

This message is displayed if an invalid button is pressed (to operate a function that the indoor unit does not have).

If a single remote controller is used to operate multiple indoor units simultaneously that are different types, this message will not be displayed as

far as any of the indoor units is equipped with the function.

Built-in temperature sensor

Displayed if the airflow is set to

low or downward during COOL

or DRY mode. (Operation varies

according to model.)

The indicator goes off in 1 hour,

when the airflow direction

also changes.

Wired remote controller (option)

Service Ref.

Mode

Power supplyInput kW

Running Current

❇1

External ﬁnish

Heat exchanger

Fan Fan (drive) ×No.

Fan motor output kW

Airﬂow (Low-Mid-High) m3/min (CFM)

External static pressure Pa

Booster heater kW

Operation control &Thermostat

Sound pressure level

(Low-Mid-High) dB (A)

Field drain pipe O.D mm (in.)

Dimensions W mm (in.)

D mm (in.)

H mm (in.)

lbs

❇1 Figures in the parentheses indicate drainpump-less Model (L).

INDOOR UNIT

Weight

35Pa

50Pa

70Pa

100Pa

150Pa

Service Ref.

Mode

Power supplyInput kW

Running Current

❇1

External ﬁnish

Heat exchanger

Fan Fan (drive) ×No.

Fan motor output kW

Airﬂow (Low-Mid-High) m3/min (CFM)

External static pressure Pa

Booster heater kW

Operation control &Thermostat

Sound pressure level

(Low-Mid-High) dB (A)

Field drain pipe O.D mm (in.)

Dimensions W mm (in.)

D mm (in.)

H mm (in.)

lbs

INDOOR UNIT

Weight

35Pa

50Pa

70Pa

100Pa

150Pa

Service Ref.

Mode

Power supplyInput kW

Running Current

❇1

External ﬁnish

Heat exchanger

Fan Fan (drive) ×No.

Fan motor output kW

Airﬂow (Low-Mid-High) m3/min (CFM)

External static pressure Pa

Booster heater kW

Operation control &Thermostat

Sound pressure level

(Low-Mid-High) dB (A)

Field drain pipe O.D mm (in.)

Dimensions W mm (in.)

D mm (in.)

H mm (in.)

lbs

INDOOR UNIT

Weight

35Pa

50Pa

70Pa

100Pa

150Pa

PEAD-RP35JA(L)Q

Cooling

0.09 (0.07)

0.64 (0.53)

Heating

0.07

0.53

Single phase, 50, 60Hz, 220-240V

Galvanized sheets

Plate fin coil

Sirocco fan ×1

0.085

10.0-12.0-14.0 (353-424-494)

35-50-70-100-150

Remote controller & built-in

23-26-29

23-27-30

24-28-31

26-29-33

29-33-37

32 (1-1/4)

900 (35-7/16)

732 (28-7/8)

250 (9-7/8)

26 (25)

58 (56)

PEAD-RP50JA(L)Q

Cooling

0.11 (0.09)

0.90 (0.79)

Heating

0.09

0.79

Single phase, 50, 60Hz, 220-240V

Galvanized sheets

Plate fin coil

Sirocco fan ×1

0.085

12.0-14.5-17.0 (424-512-600)

35-50-70-100-150

Remote controller & built-in

25-30-34

26-31-35

28-32-36

29-33-37

31-35-39

32 (1-1/4)

900 (35-7/16)

732 (28-7/8)

250 (9-7/8)

28 (27)

62 (60)

PEAD-RP60JA(L)Q

Cooling

0.12 (0.10)

1.00 (0.89)

Heating

0.10

0.89

Single phase, 50, 60Hz, 220-240V

Galvanized sheets

Plate fin coil

Sirocco fan ×2

0.121

14.5-18.0-21.0 (512-636-742)

35-50-70-100-150

Remote controller & built-in

25-28-32

25-29-33

26-30-34

27-31-35

29-34-38

32 (1-1/4)

1100 (43-5/16)

732 (28-7/8)

250 (9-7/8)

28 (27)

62 (60)

SPECIFICATION

❇1 Figures in the parentheses indicate drainpump-less Model (L).

Service Ref.

Mode

Power supplyInput kW

Running Current

❇1

External ﬁnish

Heat exchanger

Fan Fan (drive) ×No.

Fan motor output kW

Airﬂow (Low-Mid-High) m3/min (CFM)

External static pressure Pa

Booster heater kW

Operation control &Thermostat

Sound pressure level

(Low-Mid-High) dB (A)

Field drain pipe O.D mm (in.)

Dimensions W mm (in.)

D mm (in.)

H mm (in.)

lbs

INDOOR UNIT

Weight

35Pa

50Pa

70Pa

100Pa

150Pa

Service Ref.

Mode

Power supplyInput kW

Running Current

❇1

External ﬁnish

Heat exchanger

Fan Fan (drive) ×No.

Fan motor output kW

Airﬂow (Low-Mid-High) m3/min (CFM)

External static pressure Pa

Booster heater kW

Operation control &Thermostat

Sound pressure level

(Low-Mid-High) dB (A)

Field drain pipe O.D mm (in.)

Dimensions W mm (in.)

D mm (in.)

H mm (in.)

lbs

INDOOR UNIT

Weight

35Pa

50Pa

70Pa

100Pa

150Pa

Service Ref.

Mode

Power supplyInput kW

Running Current

❇1

External ﬁnish

Heat exchanger

Fan Fan (drive) ×No.

Fan motor output kW

Airﬂow (Low-Mid-High) m3/min (CFM)

External static pressure Pa

Booster heater kW

Operation control &Thermostat

Sound pressure level

(Low-Mid-High) dB (A)

Field drain pipe O.D mm (in.)

Dimensions W mm (in.)

D mm (in.)

H mm (in.)

lbs

INDOOR UNIT

Weight

35Pa

50Pa

70Pa

100Pa

150Pa

PEAD-RP70JA(L)Q

Cooling

0.17 (0.15)

1.28 (1.17)

Heating

0.15

1.17

Single phase, 50, 60Hz, 220-240V

Galvanized sheets

Plate fin coil

Sirocco fan ×2

0.121

17.5-21.0-25.0 (618-742-883)

35-50-70-100-150

Remote controller & built-in

25-29-34

26-30-34

27-31-35

28-32-36

30-35-39

32 (1-1/4)

1100 (43-5/16)

732 (28-7/8)

250 (9-7/8)

33 (32)

73 (71)

PEAD-RP100JA(L)Q

Cooling

0.25 (0.23)

1.68 (1.57)

Heating

0.23

1.57

Single phase, 50, 60Hz, 220-240V

Galvanized sheets

Plate fin coil

Sirocco fan ×2

0.244

24.0-29.0-34.0 (847-1024-1201)

35-50-70-100-150

Remote controller & built-in

28-33-38

29-34-38

30-35-39

31-36-40

34-40-43

32 (1-1/4)

1400 (55-1/8)

732 (28-7/8)

250 (9-7/8)

41 (40)

91 (89)

PEAD-RP125JA(L)Q

Cooling

0.36 (0.34)

2.40 (2.29)

Heating

0.34

2.29

Single phase, 50, 60Hz, 220-240V

Galvanized sheets

Plate fin coil

Sirocco fan ×2

0.244

29.5-35.5-42.0 (1042-4254-1483)

35-50-70-100-150

Remote controller & built-in

31-36-40

33-36-40

33-37-41

34-39-42

37-41-45

32 (1-1/4)

1400 (55-1/8)

732 (28-7/8)

250 (9-7/8)

43 (42)

95 (93)

❇1 Figures in the parentheses indicate drainpump-less Model (L).

Service Ref.

Mode

Power supplyInput kW

Running Current

❇1

External ﬁnish

Heat exchanger

Fan Fan (drive) ×No.

Fan motor output kW

Airﬂow (Low-Mid-High) m3/min (CFM)

External static pressure Pa

Booster heater kW

Operation control &Thermostat

Sound pressure level

(Low-Mid-High) dB (A)

Field drain pipe O.D mm (in.)

Dimensions W mm (in.)

D mm (in.)

H mm (in.)

lbs

INDOOR UNIT

Weight

35Pa

50Pa

70Pa

100Pa

150Pa

PEAD-RP140JA(L)Q

Cooling

0.39 (0.37)

2.60 (2.49)

Heating

0.37

2.49

Single phase, 50, 60Hz, 220-240V

Galvanized sheets

Plate fin coil

Sirocco fan ×2

0.244

32.0-39.0-46.0 (1130-1377-1624)

35-50-70-100-150

Remote controller & built-in

33-37-43

34-38-43

34-39-44

36-40-45

38-42-46

32 (1-1/4)

1600 (63)

732 (28-7/8)

250 (9-7/8)

47 (46)

104 (102)

FAN PERFORMANCE AND CORRECTED AIR FLOW

PEAD-RP35JA(L)Q

(External static pressure 35Pa) 220-240V 50/60Hz

79111315 17 19 21

Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit

Rated point

PEAD-RP35JA(L)Q

(External static pressure 50Pa) 220-240V 50/60Hz

79111315 17 19 21

Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit

Rated point

PEAD-RP35JA(L)Q

(External static pressure 70Pa) 220-240V 50/60Hz

791113 15 17 19 21

Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit Rated point

PEAD-RP35JA(L)Q

(External static pressure 100Pa) 220-240V 50/60Hz

100

110

120

791113 15 17 19 21

Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit Rated point

PEAD-RP35JA(L)Q

(External static pressure 150Pa) 220-240V 50/60Hz

100

110

120

130

140

150

160

170

791113 15 17 19 21

Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit

Rated point

PEAD-RP50JA(L)Q

(External static pressure 35Pa) 220-240V 50/60Hz

91419 Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit

Rated point

10 15 20

PEAD-RP50JA(L)Q

(External static pressure 50Pa) 220-240V 50/60Hz

91419 Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit

Rated point

10 15 20

PEAD-RP50JA(L)Q

(External static pressure 70Pa) 220-240V 50/60Hz

100

91419 Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit Rated point

10 15 20

PEAD-RP50JA(L)Q

(External static pressure 100Pa) 220-240V 50/60Hz

100

110

120

130

91419 Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit Rated point

10 15 20

PEAD-RP50JA(L)Q

(External static pressure 150Pa) 220-240V 50/60Hz

100

110

120

130

140

150

160

170

180

91419 Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit

Rated point

10 15 20

PEAD-RP60JA(L)Q

(External static pressure 35Pa) 220-240V 50/60Hz

10 15 20 25 30

Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit

Rated point

PEAD-RP60JA(L)Q

(External static pressure 50Pa) 220-240V 50/60Hz

10 15 20 25 30

Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit Rated point

PEAD-RP60JA(L)Q

(External static pressure 70Pa) 220-240V 50/60Hz

10 15 20 25 30

Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit

Rated point

PEAD-RP60JA(L)Q

(External static pressure 100Pa) 220-240V 50/60Hz

100

110

120

10 15 20 25 30

Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit

Rated point

PEAD-RP60JA(L)Q

(External static pressure 150Pa) 220-240V 50/60Hz

100

110

120

130

140

150

160

170

10 15 20 25 30

Airflow rate(m3/min)

External static pressure (Pa)

Middle

Low

High

Limit

Rated point

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Acondicionador de aire de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric SRK20ZSX-W Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PKFY-P-VKM-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr. Slim SUZ-KA25 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MXZ-2HJ40VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric SLZ Series Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric TRANE NTXWST30A112A Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr. SLIM PC-2GJA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-GF60VE Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MS-GH13VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-EF VE Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MLZ-KA25VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUHY-HP200YNW-A Cómo utilizar

Mitsubishi Electric

Mitsubishi Electric MXZ-3C30NA2 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric SLZ-KF25 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PEH-RP250MYA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-CB22VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUMY-P125VHMB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-FH06NA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSY-GN09VF Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUMY-P100 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric SLZ-KA25VA.TH Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric City Multi Series Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric Mr. Slim PLA-A12BA4 Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario