Mitsubishi Electric FR-F720-55K Manual de usuario

FR-A7NF INSTRUCTION MANUAL

INVERTER

Plug-in option

INSTRUCTION MANUAL

INVERTER

HEAD OFFICE: TOKYO BUILDING 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

FR-A7NF

FL remote

communication

function

IB(NA)-0600328ENG-D(1111) MEE Printed in Japan Specifications subject to change without notice.

PRE-OPERATION INSTRUCTIONS

INSTALLATION

WIRING

INVERTER SETTING

FL REMOTE COMMUNICATION

FUNCTION

CYCLIC TRANSMISSION

DESCRIPTION AND CORRECTIVE

ACTION OF FAULT INDICATION

MESSAGE TRANSMISSON

TROUBLESHOOTING

A-1

Thank you for choosing this Mitsubishi Inverter plug-in option.

This Instruction Manual gives handling information and

precautions for use of this equipment. Incorrect handling might

cause an unexpected fault. Before using the equipment, please

read this manual carefully to use the equipment to its optimum.

Please forward this manual to the end user.

1. Electric Shock Prevention

This section is specifically about

safety matters

Do not attempt to install, operate, maintain or inspect this

product until you have read through this Instruction Manual and

appended documents carefully and can use the equipment

correctly. Do not use this product until you have a full

knowledge of the equipment, safety information and

instructions.

In this Instruction Manual, the safety instruction levels are

classified into "WARNING" and "CAUTION".

Incorrect handling may cause

hazardous conditions, resulting in

death or severe injury.

Incorrect handling may cause

hazardous conditions, resulting in

medium or slight injury, or may cause

only material damage.

The level may even lead to a serious

consequence according to conditions. Both instruction levels

must be followed because these are important to personal

safety.

WARNING

CAUTION

SAFETY INSTRUCTIONS

WARNING

•While power is ON or when the inverter is running, do not

open the front cover. You may get an electric shock.

•Do not run the inverter with the front cover or wiring cover

removed. Otherwise, you may accidentally touch the exposed

high-voltage terminals and charging part and get an electric

shock.

•Even if power is OFF, do not remove the front cover except for

wiring or periodic inspection. You may accidentally touch the

charged inverter circuits and get an electric shock.

•Before wiring or inspection, power must be switched OFF. To

confirm that, LED indication of the operation panel must be

checked. (It must be OFF.) Any person who is involved in

wiring or inspection shall wait for at least 10 minutes after the

power supply has been switched OFF and check that there

are no residual voltage using a tester or the like. The

capacitor is charged with high voltage for some time after

power OFF, and it is dangerous.

•Any person who is involved in wiring or inspection of this

equipment shall be fully competent to do the work.

•The plug-in option must be installed before wiring. Otherwise,

you may get an electric shock or be injured.

•Do not touch the plug-in option or handle the cables with wet

hands. Otherwise you may get an electric shock.

•Do not subject the cables to scratches, excessive stress,

heavy loads or pinching. Otherwise you may get an electric

shock.

A-2

2. Injury Prevention

3. Additional Instructions

Also the following points must be noted to prevent an accidental

failure, injury, electric shock, etc.

1) Transportation and mounting

2) Trial run

3) Usage

4) Maintenance, inspection and parts replacement

5) Disposal

6) General instruction

CAUTION

•The voltage applied to each terminal must be the ones

specified in the Instruction Manual. Otherwise burst, damage,

etc. may occur.

•The cables must be connected to the correct terminals.

Otherwise burst, damage, etc. may occur.

•Polarity must be correct. Otherwise burst, damage, etc. may

occur.

•While power is ON or for some time after power-OFF, do not

touch the inverter as they will be extremely hot. Doing so can

cause burns.

CAUTION

•Do not install or operate the plug-in option if it is damaged or

has parts missing.

•Do not stand or rest heavy objects on the product.

•The mounting orientation must be correct.

•Foreign conductive objects must be prevented from entering

the inverter. That includes screws and metal fragments or

other flammable substances such as oil.

CAUTION

•Before starting operation, each parameter must be confirmed

and adjusted. A failure to do so may cause some machines to

make unexpected motions.

WARNING

•Do not modify the equipment.

•Do not perform parts removal which is not instructed in this

manual. Doing so may lead to fault or damage of the inverter.

CAUTION

•Static electricity in your body must be discharged before you

touch the product. Otherwise the product may be damaged.

CAUTION

•Do not test the equipment with a megger (measure insulation

resistance).

CAUTION

•This inverter plug-in option must be treated as industrial

waste.

Many of the diagrams and drawings in this Instruction Manual

show the inverter without a cover or partially open for

explanation. Never operate the inverter in this manner. The

cover must be reinstalled and the instructions in the inverter

manual must be followed when operating the inverter.

— CONTENTS —

1 PRE-OPERATION INSTRUCTIONS 1

1.1 Inverter model ....................................................................................................................................1

1.2 Unpacking and product confirmation ..............................................................................................2

1.2.1 Product confirmation.......................................................................................................................................2

1.2.2 SERIAL number check ...................................................................................................................................3

1.3 Parts....................................................................................................................................................7

1.4 LED status ..........................................................................................................................................8

1.4.1 Device status LED (DEV), remote status LED (RMT) ....................................................................................9

1.4.2 Transmitting (TX)/receiving (RX) LED..........................................................................................................10

1.4.3 Communication set status LED (CHG).........................................................................................................10

1.5 Specifications...................................................................................................................................11

1.5.1 Inverter option specifications........................................................................................................................11

1.5.2 Communication specifications ......................................................................................................................11

2 INSTALLATION 12

2.1 Pre-installation instructions ...........................................................................................................12

2.2 Installation of the communication option LED display cover .....................................................13

2.3 Installation procedure .....................................................................................................................14

2.4 Node address setting ......................................................................................................................16

3 WIRING 17

3.1 Connection to network ....................................................................................................................17

3.2 Cable specifications ........................................................................................................................18

3.3 Precautions for system configuration ...........................................................................................18

3.4 Wiring................................................................................................................................................19

4 INVERTER SETTING 21

4.1 Parameter list ...................................................................................................................................21

4.2 Operation mode setting...................................................................................................................24

4.2.1 Operation mode indication............................................................................................................................24

4.2.2 Operation mode switchover method.............................................................................................................25

4.3 Selection of control source for the Network operation mode .....................................................30

4.4 Operation at communication error occurrence ............................................................................32

4.4.1 Operation selection at communication error occurrence (Pr. 501, Pr. 502) .................................................32

4.4.2 Fault and measures......................................................................................................................................34

4.5 Inverter reset ....................................................................................................................................36

4.6 Frequency and speed conversion specifications.........................................................................37

5 FL REMOTE COMMUNICATION FUNCTION 38

5.1 Functions..........................................................................................................................................38

5.1.1 Output from the inverter to the network........................................................................................................38

5.1.2 Input to the inverter from the network...........................................................................................................39

5.2 Types of data communication ........................................................................................................40

6 CYCLIC TRANSMISSION 41

6.1 Common memory ............................................................................................................................42

6.1.1 Common memory area 1..............................................................................................................................44

6.1.2 Common memory area 2..............................................................................................................................45

6.2 Output data (master to inverter) .....................................................................................................48

6.2.1 Control input command ................................................................................................................................49

6.2.2 Set frequency ...............................................................................................................................................51

III

6.3 Input data (inverter to master) ........................................................................................................52

6.3.1 Inverter status monitor..................................................................................................................................53

6.3.2 Fault code.....................................................................................................................................................55

6.3.3 Life/warning ..................................................................................................................................................55

6.3.4 Output frequency monitor .............................................................................................................................57

6.3.5 Output current monitor..................................................................................................................................57

7 MESSAGE TRANSMISSON 58

7.1 Error response at word block read/write .......................................................................................61

7.2 Word block read/write .....................................................................................................................62

7.2.1 Virtual address space of word block read/write............................................................................................63

7.2.2 Product information ......................................................................................................................................64

7.2.3 Operation mode............................................................................................................................................66

7.2.4 Inverter status...............................................................................................................................................67

7.2.5 Set frequency ...............................................................................................................................................68

7.2.6 Inverter monitor ............................................................................................................................................69

7.2.7 Parameter.....................................................................................................................................................72

7.2.8 Calibration parameters .................................................................................................................................74

7.2.9 Fault record ..................................................................................................................................................76

7.3 Network parameter read..................................................................................................................82

7.4 Log data read ...................................................................................................................................85

7.5 Log data clear...................................................................................................................................88

7.6 Profile read .......................................................................................................................................89

7.7 Message loopback ...........................................................................................................................93

8 DESCRIPTION AND CORRECTIVE ACTION OF FAULT INDICATION 94

9 TROUBLESHOOTING 95

1PRE-OPERATION INSTRUCTIONS

1.1 Inverter model

The inverter model, 55K and 75K stated in this Instruction Manual differs according to each -NA, -EC, -

CH(T) versions. Refer to the following correspondence table for each inverter model. (Refer to the Instruction

Manual of each inverter for the inverter model.)

For example, "for the 75K or higher" indicates "for the FR-A740-01440-NA or higher" in the case of FR-

A740 of NA version.

NA EC CH

F700

FR-F720(P)-55K FR-F720-02330-NA ⎯⎯

FR-F720(P)-75K FR-F720-03160-NA ⎯⎯

FR-F740(P)-55K FR-F740-01160-NA FR-F740-01160-EC FR-F740-55K-CH(T)

FR-F740(P)-75K FR-F740-01800-NA FR-F740-01800-EC FR-F740-S75K-CH(T)

A700

FR-A720-55K FR-A720-02150-NA ⎯⎯

FR-A720-75K FR-A720-02880-NA ⎯⎯

FR-A740-55K FR-A740-01100-NA FR-A740-01800-EC FR-A740-55K-CHT

FR-A740-75K FR-A740-01440-NA FR-A740-02160-EC FR-A740-75K-CHT

PRE-OPERATION INSTRUCTIONS

1.2 Unpacking and product confirmation

Take the plug-in option out of the package, check the product name, and confirm that the product is as you

ordered and intact.

This product is a plug-in option for the FR-A700/F700(P) series inverter.

1.2.1 Product confirmation

Check the enclosed items.

Plug-in option

......................................... 1

Mounting screw (M3 ×6mm)

............ 2 (Refer to page 14.)

Hex-head screw for option

mounting (5.5mm)

............. 1 (Refer to page 14.)

Communication option LED

display cover

............ 1 (Refer to page 13.)

5.5mm

PRE-OPERATION INSTRUCTIONS

1.2.2 SERIAL number check

The plug-in option is compatible with the inverter having the following SERIAL number or later.

Check the SERIAL number indicated on the inverter rating plate or package.

zSERIAL number check

Refer to the inverter manual for the location of the rating plate.

(1) PU/NET operation switchover (X65 signal) specification

The inverters with the following SERIAL are operated in the PU/NET operation switchover (X65 signal)

specification when connected with FR-A7NF.

zFR-A700 series

zFR-F700 series Japanese specification

Regardless of their SERIAL numbers, all FR-F700P series inverters are operated with the PU operation interlock

(X12 signal) specification.

Rating plate example

{ { {{{{{{ SERIAL

Symbol Year Month Control number

TC{{{A{{{G{{ TC number

The SERIAL consists of one symbol, two characters indicating production year and month, and six characters indicating control number.

The last digit of the production year is indicated as the Year, and the Month is indicated by 1 to 9, X (October), Y (November), or Z (December.)

Model SERIAL number

FR-A720-(-NA),

FR-A740-(-NA)(-EC)(-CHT),

FR-CA70-EC, FR-CA70-ECT

7X{{{{{{ to

03{{{{{{

Model SERIAL number

FR-F720-0.75K to 110K,

FR-F740-0.75K to 560K 91{{{{{{ or later

PRE-OPERATION INSTRUCTIONS

zFR-F700 series NA specification

zFR-F700 series EC specification

zFR-F700 series CHT specification

Model SERIAL number

FR-F720-00046 to 04750-NA,

FR-F740-00023 to 12120-NA 91{{{{{{ or later

Model SERIAL number

FR-F740-00023 to 00620-EC,

FR-CF70-EC, FR-CF70-ECT 95{{{{{{ or later

Model SERIAL number

FR-F740-0.75K to 55K-CHT,

FR-F740-S75K to S630K-CHT 93{{{{{{ or later

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Acondicionador de aire de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PLA Series Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric PK12FK Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric MXZ-2C20NA2 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PLA-A-BA4 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PKA-A KA4 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSB-20EXML35-501 Manual de referencia

Mitsubishi Electric

Mitsubishi Electric MSZ-A09YV SERIES Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PLA-SM71EA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-FT25VG-E1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-FE09/12NA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric American Standart NAXWST06A 112A Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-AP25VGK Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUMY-P60NKMU1 Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric MSZ-DM50VA-ER1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-HR25VF Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUMY-P36NHMU Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AE-200A Cómo utilizar

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PEFY-P54NMAU-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Lossnay LGH-25RX5 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PLA-RP AA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PUHZ-SHW80VHA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PFD-P250VM-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric TRANE NTXWST06A112A Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.SLIM MS24WN Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario