Mitsubishi Electric Mr.Slim PLA Series Manual de funcionamiento

TECHNICAL & SERVICE MANUAL

CONTENTS

1. COMBINATION OF INDOORAND OUTDOOR UNITS··2

2. SAFETY PRECAUTION·······························2

3. PART NAMES AND FUNCTIONS ···············4

4. SPECIFICATIONS········································7

5. DATA ····························································9

6. OUTLINES AND DIMENSIONS·················17

WIRING DIAGRAM

·······································18

REFRIGERANT SYSTEM DIAGRAM

··············19

9. TROUBLESHOOTING ·······························20

10. DISASSEMBLY PROCEDURE ··················22

11. PARTS LIST ···············································25

12. OPTIONAL PARTS ····································28

Indoor unit

[Model names] [Service Ref.]

PLA-P3AA PLA-P3AA

No.OC287

• Refer to the OCT03 REVISED

EDITION-E as for control relation.

• This manual does not cover

outdoor units. When serving

them, please refer to the service

manual No.OC285, OC261

REVISED EDITION-B and this

manual in a set.

INDOOR UNIT

Ceiling Cassettes

Series PLA

WIRED REMOTE

CONTROLLER

R407C

WIRELESS REMOTE

CONTROLLER

SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS

SPLIT-TYPE, AIR CONDITIONERS

ON/OFF TEMP

MODEL SELECT

NOT AVAILABLE

CHECK

TEST RUN

˚C

AMPM

ON/OFF

CENTRALLY CONTROLLED

ERROR CODE

CLOCK

ON OFF

˚C

CHECK

CHECK MODE

FILTER

TEST RUN

FUNCTION

˚C

1Hr.

NOT AVAILABLE

STAND BY

DEFROST

TEMP.

2003

OC287-1.qxp 03.3.19 10:46 AM Page 1

1COMBINATION OF INDOOR AND OUTDOOR UNITS

2SAFETY PRECAUTION

Cautions for devices that use R407C refrigerant.

· Do not use the existing refrigerant piping.

-The old refrigerant and lubricating oil in the existing piping contains a large amount of chlorine which may cause the lubricating

oil of the new unit to deteriorate.

· Use “low residual oil piping”.

-If there is a large amount of residual oil (hydraulic oil, etc.) inside the piping and joints, deterioration of the lubricating oil will

result.

· Store the piping to be used during installation indoors and keep both ends of the piping sealed until just before

brazing. (Store elbows and other joints in a plastic bag.)

-If dust, dirt, or water enters the refrigerant cycle, deterioration of the oil and compressor trouble may result.

· Use Suniso 4GS or 3GS (small amount) as the lubricating oil to coat flares and flange connection parts.

-The lubricating oil used with the air conditioner is highly hygroscopic. If it is used, water may be mixed in and deterioration

of the lubricating oil may result.

· Use liquid refrigerant to charge the system.

-If gas refrigerant is used to charge the system, the composition of the refrigerant in the cylinder will change and perfor-

mance may drop.

· Do not use a refrigerant other than R407C.

-If another refrigerant (R22, etc.) is used, the chlorine in the refrigerant may cause the lubricating oil to deteriorate.

· Use a vacuum pump with a reverse flow check valve.

-The vacuum pump oil may flow back into the refrigerant cycle and cause the lubricating oil to deteriorate.

Heat pump type

Outdoor unit(OC285)

PUH-P3

VGAA VGAA

Heat pump type

Outdoor unit(OC261 REVISED EDITION-B)

PUH-P3 Cooling only type

PU-P3

Cooling only type

PU-P3

Indoor unit

PLA-P3AA

VGAA.UK

VGAA1.UK YGAA.UK

YGAA1.UK VGAA.UK

VGAA1.UK YGAA.UK

YGAA1.UK

OC287-1.qxp 03.3.19 10:46 AM Page 2

[2] Notice on repair service

·After recovering all the refrigerant in the unit, work may be started.

·Do not release the refrigerant in the air.

·After completing the repair service, recharge the system with the specified amount of the

liquid refrigerant.

[3] Refrigerant recharging

(1) Refrigerant recharging process

Direct charging from the cylinder.

·Confirm that the cylinder is suitable for syphoning.

·Raise the cylinder and recharge the unit by syphoning liquid refrigerant.

(2) Recharge when refrigerant leakage has occurred.

·After recovering all the refrigerant in the unit, work may be started.

·Do not release the refrigerant in the air.

·After completing the repair service, recharge the system with the specified amount of

the liquid refrigerant.

Gravimeter

Unit

[1] Service tools

Use the below service tools as exclusive tools for R407C refrigerant.

No. Tool name Specifications

1Gauge manifold ·Only for R407C.

·Use the existing fitting SPECIFICATIONS. (UNF7/16)

·Use high-tension side pressure of 3.4 MPa or over.

2Charge hose ·Only for R407C.

·Use pressure performance of 5.1 MPa or over.

3Electronic scale

4Gas leak detector ·Use the detector for R134a or R407C.

5Adapter for reverse flow check. ·Attach on vacuum pump.

6Refrigerant charge base.

7Refrigerant cylinder. ·For R407C ·Top of cylinder (Brown)

·Cylinder with syphon

8Refrigerant recovery equipment.

OC287-1.qxp 03.3.19 10:46 AM Page 3

● Operation buttons

PAR-20MAA

ON/OFF

CENTRALLY CONTROLLED

ERROR CODE

CLOCK

ON OFF

˚C

CHECK

CHECK MODE

FILTER

TEST RUN

FUNCTION

˚C

1Hr.

NOT AVAILABLE

STAND BY

DEFROST

FILTER

CHECK TEST

TEMP.

TIMER SET

This sets the ventilation fan speed.

VENTILATION button

Press this button to switch the cooler,

electronic dry (dehumidify), automatic

and heater modes.

OPERATION SWITCH button

This sets the room temperature. The

temperature setting can be performed

in 1:units

Setting range

Cooler 19:to 30:

Heater 17:to 28:

TEMP. ADJUSTMENT button

This switches between continuous

operation and the timer operation.

TIMER button

This switches between the operation

and stop modes each time it is pressed.

The lamp on this button lights during

operation.

ON/OFF button

Only press this button to perform an

inspection check or test operation.

Do not use it for normal operation.

CHECK-TEST RUN button

This switch the horizontal fan motion

ON and OFF.

(Not available for this model.)

LOUVER button

This adjusts the vertical angle of the

ventilation.

AIR DIRECTION button

This resets the filter service indication

display

FILTER button

This sets the current time, start time

and stop time.

TIME SETTING button

This sets the ventilation fan speed.

AIR SPEED button

PLA-P3AA

3PART NAMES AND FUNCTIONS

On the controls are set, the same operation mode can be repeated by simply pressing the ON/OFF button.

Auto Air Swing Vane

Disperses airflow up and

down and adjusts the angle

of airflow direction.

Grille

Filter

Removes dust and pollutants

from intake air

Horizontal Air Outlet

Sets airflow of horizontal automatically

during cooling or dehumidifying.

Air Intake

Intakes air from room.

● Indoor (Main) Unit

PLA-P3AA

● Wired remote controller

OC287-1.qxp 03.3.19 10:46 AM Page 4

Caution

●Only the Power display lights when the unit is stopped and power supplied to the unit.

●When the central control remote control unit, which is sold separately, is used the ON-OFF button, operation switch button

and TEMP. adjustment button do not operate.

●“NOT AVAILABLE” is displayed when the Air speed button are pressed.This indicates that this room unit is not equipped

with the fan direction adjustment function and the louver function.

●When power is turned ON for the first time, it is normal that “H0” is displayed on the room temperature indication (For max.

2minutes). Please wait until this “H0” indication disappear then start the operation.

CENTRALLY

CONTROLLED display

This indicates when the unit is con-

trolled by optional features such as

central control type remote controller.

TIMER display

This indicates when the continuous

operation and time operation modes

are set.

It also display the time for the timer

operation at the same time as when

it is set.

OPERATION MODE display

This indicates the operation mode.

STANDBY display

The [STANDBY] symbol is only dis-

played from the time the heating

operation starts unit the heated air

begins to blow.

DEFROST display

This indicates when the defrost oper-

ation is performed.

CHECK display

This indicates when a malfunction

has occurred in the unit which should

be checked.

CLOCK display

The current time , start time and stop

time can be displayed in ten second

intervals by pressing the time switch

button. The start time or stop time is

always displayed during the timer

operation.

●Display

In this display example on the bot-

tom left, a condition where all dis-

play lamps light is shown for expla-

nation purposes although this differs

from actual operation.

Operation lamp

This lamp lights during operation,

goes off when the unit stops and

flashes when a malfunction occurs.

POWER display

This lamp lights when electricity is

supplied to the unit.

SET TEMPERATURE display

This displays the selected setting

temperature.

AIR DIRECTION display

This displays the air direction.

ROOM TEMPERATURE display

The temperature of the suction air

is displayed during operation. The

display range is 8°C to 39°C. The

display flashes 8°C when the actual

temperature is less than 8°C and

flashes 39°C when the actual tem-

perature is greater than 39°C.

display

This display lights in the check mode

or when a test operation is per-

formed.

CHECK MODE

TEST RUN

This lamp lights when the filter need

to be cleaned.

AIR SPEED display

The selected fan speed is displayed.

FILTER display

PAR-20MAA

ON/OFF

CENTRALLY CONTROLLED

ERROR CODE

CLOCK

ON OFF

˚C

CHECK

CHECK MODE

FILTER

TEST RUN

FUNCTION

˚C

1Hr.

NOT AVAILABLE

STAND BY

DEFROST

FILTER

CHECK TEST

TEMP.

TIMER SET

OC287-1.qxp 03.3.19 10:46 AM Page 5

ON/OFF TEMP

FAN

VANE

TEST RUN

AUTO STOP

AUTO START

min

LOUVER

MODE

CHECK

RESETSET CLOCK

MODEL SELECT

NOT AVAILABLE

CHECK

TEST RUN

˚C

AMPM

VANE CONTROL button

Used to change the air flow direction.

CLOCK button

RESET button

SET button

ON/OFF button

The unit is turned ON and OFF alternately

each time the button is pressed.

LOUVER button

This switch the horizontal fan motion ON

and OFF.

(Not available for this model.)

MODE SELECT button

Used to switch the operation mode between

cooling, drying, blowing, heating and auto

mode.

CHECK-TEST RUN button

Only press this button to perform an inspec-

tion check or test operation.

Do not use it for normal operation.

FAN SPEED SELECT button

Used to change the fan speed.

TIMER display

Displays when in timer operation or when

setting timer.

button

SET TEMPERATURE button sets any desired

room temperature.

CLOCK display

Displays the current time.

“” “ ” display

Displays the order of timer operation.

“ ” “ ” display

Displays whether timer is on or off.

wIn case the outdoor unit is cool only type,

the heating mode is not available.

Buttons used to set the “hour and minute” of

the current time and timer settings.

h and min buttons

display

SET TEMP. display indicates desired temper-

ature set.

display

FAN SPEED display indicates which fan

speed has been selected.

display

The vertical direction of air flow is indicated.

display

Blinks when model is selected.

display

Lights up while transmission to the indoor

unit is mode using switches.

display

CHECK&TEST RUN display indicates that

the unit is being checked or test-run.

display

OPERATION MODE display

Operation mode display indicates which op-

eration mode is in effect.

TIMER CONTROL buttons

AUTO STOP (OFF timer): when this switch

is set, the air conditioner will be au-

tomatically stopped at the preset time.

AUTO START (ON timer): when this switch

is set, the air conditioner will be automatical-

ly started at the preset time.

MODEL SELECT

CHECK

TEST RUN

● Wireless remote controller

PLA-P3AA

●When cover is open.

OC287-1.qxp 03.3.19 10:46 AM Page 6

SPECIFICATIONS

Service Ref.

Item

Function

Capacity

Total input

NOTE: 1. Rating conditions (ISO T1)

Cooling Indoor : D.B. 27°C (80°F) W.B. 19°C (66°F) Outdoor : D.B. 35°C (95°F) W.B. 24°C (75°F)

Heating Indoor : D.B. 20°C (80°F) Outdoor : D.B. 7°C (45°F) W.B. 6°C (43°F)

Refrigerant piping length (one way) : 5m (16ft.)

2. Guaranteed operating range Indoor Outdoor

Cooling Upper limit D.B. 35˚C, W.B. 22.5˚C D.B. 46˚C

Lower limit D.B. 19˚C, W.B. 15˚C D.B. -5˚C

Heating Upper limit D.B. 28˚C D.B. 24˚C, W.B. 18˚C

Lower limit D.B. 17˚C D.B. -11˚C, W.B. -12˚C

3. Above data based on indicated voltage

Indoor unit Single phase 240V 50Hz

Outdoor unit Single phase 240V 50Hz / 3 phase 415V 50Hz

Btu/h

K/ min (CFM)

Pa (mmAq)

mm (in.)

kg (lbs.)

K/ min (CFM)

mm (in.)

kg (lbs.)

mm (in.)

Service Ref.

Power supply (phase, cycle,voltage)

Input

Running current

Starting current

External finish (Panel)

Heat exchanger

Fan (drive) oNo.

Fan Fan motor output

Airflow (Lo-Mi2-Mi1-Hi)

External static pressure

Booster heater

Operation control & Thermostat

Sound level (Lo-Mi2-Mi1-Hi)

Unit drain pipe I.D. W

Dimensions D

Weight

Service Ref.

Power supply (phase, cycle, voltage)

Running current

Starting current

External finish

Refrigerant control

Compressor

Model

Motor output

Starter type

Protection devices

Crankcase heater

Heat exchanger

Fan (drive) oNo

Fan Fan motor output

Airflow

Defrost method

Sound level Cooling

Heating

Dimensions D

Weight

Refrigerant

Charge

Oil (Model)

Pipe size O.D. Liquid

Gas

Connection method Indoor side

Outdoor side

Between the indoor & Height difference

outdoor units Piping length

Cooling

26,600

7,800

3.44

0.17

0.81

1.0

15.01············GAA

14.81/5.29····GAA(1).UK

PLA-P3AA

Single phase, 50Hz, 220-230-240V

Munsell 0.70Y 8.59/0.97

Plate fin coil

Turbo fan (direct) o1

0.070

15-16-18-20 (530-565-635-705)

0 (direct blow)

—

Remote controller & built-in

28-30-32-34

32 (1-1/4)

Single phase, 50Hz, 220-230-240V / 3 phase, 50Hz, 380-400-415V (4wires)

93/47

Munsell 5Y 8/1······GAA

Munsell 5Y 7/1······GAA(1).UK

Linear expansion valve

Hermetic

NE52VNJMT/NE52YDKMT

2.5

Line start

Plate fin coil

Propeller (direct) o1

0.070

50 (1,770)

Reverse cycle

900(35-7/16)

330+20(13+3/4)

855(33-5/8)

79(174)

R407C

3.3(7.3)

1.3 (Ester) MEL56

9.52(3/8)

15.88(5/8)

Flared

Max. 50m

Heating

31,700

9,300

3.50

0.17

0.81

1.0

15.98············GAA

15.76/5.63····GAA(1).UK

UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)

UNIT : 258 (10-1/2) PANEL : 30 (1-3/16)

UNIT : 24 (53) PANEL : 5 (11)

Indoor unit

Outdoor unitRefrigerant piping

PUH-P3VGAA

PUH-P3VGAA.UK PUH-P3YGAA.UK

PUH-P3VGAA1.UK PUH-P3YGAA1.UK

Inner thermostat,

HP switch, Discharge thermo Thermal relay,

HP switch, Discharge thermo.

1. Heat pump type

OC287-1.qxp 03.3.19 10:46 AM Page 7

PLA-P3AA

Cooling

26,600

7,800

3.44

PLA-P3AA

Single phase, 50Hz, 220-230-240V

0.17

0.81

1.0

Munsell 0.70Y 8.59/0.97

Plate fin coil

Turbo fan (direct) o1

0.070

15-16-18-20 (530-565-635-705)

0 (direct blow)

—

Remote controller & built-in

28-30-32-34

32 (1-1/4)

Single phase, 50Hz, 220-230-240V / 3 phase, 50Hz, 380-400-415V (4wires)

15.01············GAA

14.81/5.29····GAA(1).UK

93/47

Munsell 5Y 8/1······GAA

Munsell 5Y 7/1······GAA(1).UK

Linear expansion valve

Hermetic

NE52VNJMT/NE52YDKMT

2.5

Line start

Plate fin coil

Propeller (direct) o1

0.070

50 (1,770)

Reverse cycle

900(35-7/16)

330+20(13+3/4)

855(33-5/8)

79(174)

R407C

3.3(7.3)

1.3 (Ester) MEL56

9.52(3/8)

15.88(5/8)

Flared

Max. 50m

UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)

UNIT : 258 (10-1/2) PANEL : 30 (1-3/16)

UNIT : 24 (53) PANEL : 5 (11)

Service Ref.

Item

Function

Capacity

Total input

NOTE: 1. Rating conditions (ISO T1)

Cooling Indoor : D.B. 27°C (80°F) W.B. 19°C (66°F) Outdoor : D.B. 35°C (95°F) W.B. 24°C (75°F)

Heating Indoor : D.B. 20°C (80°F) Outdoor : D.B. 7°C (45°F) W.B. 6°C (43°F)

Refrigerant piping length (one way) : 5m (16ft.)

2. Guaranteed operating range Indoor Outdoor

Cooling Upper limit D.B. 35˚C, W.B. 22.5˚C D.B. 46˚C

Lower limit D.B. 19˚C, W.B. 15˚C D.B. -5˚C

Heating Upper limit D.B. 28˚C D.B. 24˚C, W.B. 18˚C

Lower limit D.B. 17˚C D.B. -11˚C, W.B. -12˚C

3. Above data based on indicated voltage

Indoor unit Single phase 240V 50Hz

Outdoor unit Single phase 240V 50Hz / 3 phase 415V 50Hz

Btu/h

K/ min (CFM)

Pa (mmAq)

mm (in.)

kg (lbs.)

K/ min (CFM)

mm (in.)

kg (lbs.)

mm (in.)

Service Ref.

Power supply (phase, cycle,voltage)

Input

Running current

Starting current

External finish (Panel)

Heat exchanger

Fan (drive) oNo.

Fan Fan motor output

Airflow (Lo-Mi2-Mi1-Hi)

External static pressure

Booster heater

Operation control & Thermostat

Sound level (Lo-Mi2-Mi1-Hi)

Unit drain pipe I.D. W

Dimensions D

Weight

Service Ref.

Power supply (phase, cycle, voltage)

Running current

Starting current

External finish

Refrigerant control

Compressor

Model

Motor output

Starter type

Protection devices

Crankcase heater

Heat exchanger

Fan (drive) oNo

Fan Fan motor output

Airflow

Defrost method

Sound level Cooling

Heating

Dimensions D

Weight

Refrigerant

Charge

Oil (Model)

Pipe size O.D. Liquid

Gas

Connection method Indoor side

Outdoor side

Between the indoor & Height difference

outdoor units Piping length

Indoor unit

Outdoor unitRefrigerant piping

PU-P3VGAA

PU-P3VGAA.UK PU-P3YGAA.UK

PU-P3VGAA1.UK PU-P3YGAA1.UK

Inner thermostat,

HP switch, Discharge thermo Thermal relay,

HP switch, Discharge thermo.

2. Cooling only type

OC287-1.qxp 03.3.19 10:46 AM Page 8

DATA

Indoor Indoor Outdoor intake air D.B. (:)

intake air intake air 20 25 30

D.B. (:) W.B. (:) CA SHC SHF P.C. CA SHC SHF P.C. CA SHC SHF P.C.

20 16 7,722 4,942 0.64 2.75 7,488 4,792 0.64 2.91 7,254 4,643 0.64 3.08

20 18 8,268 4,299 0.52 2.80 8,034 4,178 0.52 2.96 7,761 4,036 0.52 3.16

20 20 8,892 3,557 0.40 2.89 8,697 3,479 0.40 3.03 8,463 3,385 0.40 3.23

22 16 7,722 5,560 0.72 2.75 7,488 5,391 0.72 2.91 7,254 5,223 0.72 3.08

22 18 8,268 4,961 0.60 2.80 8,034 4,820 0.60 2.96 7,761 4,657 0.60 3.16

22 20 8,892 4,268 0.48 2.89 8,697 4,175 0.48 3.03 8,463 4,062 0.48 3.23

24 16 7,722 6,178 0.80 2.75 7,488 5,990 0.80 2.91 7,254 5,803 0.80 3.08

24 18 8,268 5,622 0.68 2.80 8,034 5,463 0.68 2.96 7,761 5,277 0.68 3.16

24 20 8,892 4,980 0.56 2.89 8,697 4,870 0.56 3.03 8,463 4,739 0.56 3.23

26 16 7,722 6,795 0.88 2.75 7,488 6,589 0.88 2.91 7,254 6,384 0.88 3.08

26 18 8,268 6,284 0.76 2.80 8,034 6,106 0.76 2.96 7,761 5,898 0.76 3.16

26 20 8,892 5,691 0.64 2.89 8,697 5,566 0.64 3.03 8,463 5,416 0.64 3.23

28 16 7,722 7,413 0.96 2.75 7,488 7,188 0.96 2.91 7,254 6,964 0.96 3.08

28 18 8,268 6,945 0.84 2.80 8,034 6,749 0.84 2.96 7,761 6,519 0.84 3.16

28 20 8,892 6,402 0.72 2.89 8,697 6,262 0.72 3.03 8,463 6,093 0.72 3.23

30 16 7,722 7,722 1.00 2.75 7,488 7,488 1.00 2.91 7,254 7,254 1.00 3.08

30 18 8,268 7,607 0.92 2.80 8,034 7,391 0.92 2.96 7,761 7,140 0.92 3.16

30 20 8,892 7,114 0.80 2.89 8,697 6,958 0.80 3.03 8,463 6,770 0.80 3.23

32 16 7,722 7,722 1.00 2.75 7,488 7,488 1.00 2.91 7,254 7,254 1.00 3.08

32 18 8,268 8,268 1.00 2.80 8,034 8,034 1.00 2.96 7,761 7,761 1.00 3.16

32 20 8,892 7,825 0.88 2.89 8,697 7,653 0.88 3.03 8,463 7,447 0.88 3.23

34 16 7,722 7,722 1.00 2.75 7,488 7,488 1.00 2.91 7,254 7,254 1.00 3.08

34 18 8,268 8,268 1.00 2.80 8,034 8,034 1.00 2.96 7,761 7,761 1.00 3.16

34 20 8,892 8,536 0.96 2.89 8,697 8,349 0.96 3.03 8,463 8,124 0.96 3.23

PLA-P3AA / PU(H)-P3VGAA PU(H)-P3VGAA.UK PU(H)-P3VGAA1.UK

PU(H)-P3YGAA.UK PU(H)-P3YGAA1.UK (240V)

NOTE: CA: Capacity (W) SHC: Sensible heat capacity (W)

P.C.: Power consumption (kW) SHF: Sensible heat factor

COOLING CAPACITY(1)

1. PERFORMANCE DATA

OC287-1.qxp 03.3.19 10:46 AM Page 9

1010

Indoor Indoor Outdoor intake air D.B. (:)

intake air intake air 35 40 45

D.B. (:) W.B. (:) CA SHC SHF P.C. CA SHC SHF P.C. CA SHC SHF P.C.

20 16 6,942 4,443 0.64 3.30 6,630 4,243 0.64 3.54 6,318 4,044 0.64 3.84

20 18 7,488 3,894 0.52 3.39 7,254 3,772 0.52 3.65 6,786 3,529 0.52 3.92

20 20 8,112 3,245 0.40 3.47 7,800 3,120 0.40 3.72 7,332 2,933 0.40 3.99

22 16 6,942 4,998 0.72 3.30 6,630 4,774 0.72 3.54 6,318 4,549 0.72 3.84

22 18 7,488 4,493 0.60 3.39 7,254 4,352 0.60 3.65 6,786 4,072 0.60 3.92

22 20 8,112 3,894 0.48 3.47 7,800 3,744 0.48 3.72 7,332 3,519 0.48 3.99

24 16 6,942 5,554 0.80 3.30 6,630 5,304 0.80 3.54 6,318 5,054 0.80 3.84

24 18 7,488 5,092 0.68 3.39 7,254 4,933 0.68 3.65 6,786 4,614 0.68 3.92

24 20 8,112 4,543 0.56 3.47 7,800 4,368 0.56 3.72 7,332 4,106 0.56 3.99

26 16 6,942 6,109 0.88 3.30 6,630 5,834 0.88 3.54 6,318 5,560 0.88 3.84

26 18 7,488 5,691 0.76 3.39 7,254 5,513 0.76 3.65 6,786 5,157 0.76 3.92

26 20 8,112 5,192 0.64 3.47 7,800 4,992 0.64 3.72 7,332 4,692 0.64 3.99

28 16 6,942 6,664 0.96 3.30 6,630 6,365 0.96 3.54 6,318 6,065 0.96 3.84

28 18 7,488 6,290 0.84 3.39 7,254 6,093 0.84 3.65 6,786 5,700 0.84 3.92

28 20 8,112 5,841 0.72 3.47 7,800 5,616 0.72 3.72 7,332 5,279 0.72 3.99

30 16 6,942 6,942 1.00 3.30 6,630 6,630 1.00 3.54 6,318 6,318 1.00 3.84

30 18 7,488 6,889 0.92 3.39 7,254 6,674 0.92 3.65 6,786 6,243 0.92 3.92

30 20 8,112 6,490 0.80 3.47 7,800 6,240 0.80 3.72 7,332 5,866 0.80 3.99

32 16 6,942 6,942 1.00 3.30 6,630 6,630 1.00 3.54 6,318 6,318 1.00 3.84

32 18 7,488 7,488 1.00 3.39 7,254 7,254 1.00 3.65 6,786 6,786 1.00 3.92

32 20 8,112 7,139 0.88 3.47 7,800 6,864 0.88 3.72 7,332 6,452 0.88 3.99

34 16 6,942 6,942 1.00 3.30 6,630 6,630 1.00 3.54 6,318 6,318 1.00 3.84

34 18 7,488 7,488 1.00 3.39 7,254 7,254 1.00 3.65 6,786 6,786 1.00 3.92

34 20 8,112 7,788 0.96 3.47 7,800 7,488 0.96 3.72 7,332 7,039 0.96 3.99

COOLING CAPACITY (2)

PLA-P3AA / PU(H)-P3VGAA PU(H)-P3VGAA.UK PU(H)-P3VGAA1.UK

PU(H)-P3YGAA.UK PU(H)-P3YGAA1.UK (240V)

NOTE: CA: Capacity (W) SHC: Sensible heat capacity (W)

P.C.: Power consumption (kW) SHF: Sensible heat factor

OC287-1.qxp 03.3.19 10:46 AM Page 10

Otros manuales para Mr.Slim PLA Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Acondicionador de aire de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric MSZ-GS06NA - U1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr. Slim MXZ-2B20NA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PLA-SM71EA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric City Multi PKFY-P06NAMU-E Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric Mr.Slim MFZ-KA12NA Guía de instalación y uso

Mitsubishi Electric

Mitsubishi Electric MSZ-WN25VA - E1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUZ-ZM60VHA2 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-GS07VF Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-JP09WA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PEH-RP250MYA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.SLIM PUZ-ZM200YKA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr. SLIM PLA-M EA Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-HE09NA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric TRANE NTXWST30A112A Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PLA-RP.BA Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-AP42VGK Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PMH-P25BA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric SRK63HE-S1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PLFY-P20VCM-E Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric PEA Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MXZ-2E52VAD2 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PLA-A.BA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PWFY-P100VM-E-BU Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario