Mircom RB-MD-1113 Manual de usuario

LT-1167 Rev 0

December 2013

Model RB-MD-1113

Replacement MD-1113 Module Board

Installation Instructions

The RB-MD-1113 kit comes with all the parts needed to replace an MD-1113 module board for a TX3-CX-A8 Aperio

Door Controller.

RB-MD-1113 Installation Instructions

To replace the MD-1113 you must:

A. Power down the TX3-CX-A8

B. Replace the MD-1113 module board

C. Power up the TX3-CX-A8

Instructions on how to perform each of these steps are given in the following sections.

A. Power down the TX3-CX-A8

1. Turn off the main controller board (see SW1 in Figure 1).

2. If present, disconnect the backup battery from the current main controller board.

3. Disconnect the power cable from the power terminals on the current main controller board.

B. Replace the MD-1113 module board

1. Disconnect the ribbon cable from P3 on the MD-1067 board.

2. Disconnect the + and - wires from the RS-485 terminal on the current MD-1113 Module board.

3. Remove the four mounting screws from the current MD-1113 Module board.

4. Attach the new MD-1113 to the four spacers with the four screws provided.

5. Connect ribbon cable from the new MD-1113 Module board to P3 on the MD-1067 board.

6. Connect the + and - wires that you removed in step 2 to the RS-485 terminal on the new board.

Note: For the main operation of the MD-1113, jumpers JW1 and JW2 should be left open.

C. Power up the TX3-CX-A8

1. Connect the power cable to the power terminals on the new board.

2. If present, connect the backup battery to the new board.

3. Turn on the main controller board.

Figure 1: RB-MD-1113 Board Replacement

SW2

Power terminals for

16 Vac transformer

(PS-4 or PS-4P)

Input terminals Output terminals

Connectors

for 12V

battery backup

P6 P5

BAT- BAT+

-S

+-S+

INPUT OUTPUT

NC CNO NC CNO NC CNO NC CNO NC CNO NC CNO

Mounting

screws for the

MD-1113

OFF ON

SW1

Ribbon cable

connector for

MD-1113

Tabla de contenidos

Otros manuales de Unidad de control de Mircom

Mircom

Mircom QMP-5100AX Manual de usuario

Mircom

Mircom RB-MD-950 Guía

Mircom

Mircom RAX-332 Manual de usuario

Mircom

Mircom BBX-2000 Manual de usuario

Mircom

Mircom QDV-1000 Manual de usuario

Mircom

Mircom TX3-MDM Manual de usuario

Mircom

Mircom RB-MD-750 Manual de usuario

Mircom

Mircom MIX-M500MAP Manual de usuario

Mircom

Mircom MIX-100R Manual de usuario

Mircom

Mircom QIF-2011 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario