Miranda DENSITE UAP-1783 Guía de instalación

DENSITÉ series

UAP-1783

Eight Channel Universal Audio Processor

Guide to Installation and Operation

M768-8900-100

15 May 2007

Miranda

Technologies Inc.

3499 Douglas-B.-Floreani

St-Laurent, Québec, Canada H4S 1Y6

Tel. 514-333-1772

Fax. 514-333-9828

www.miranda.com

GUIDE TO INSTALLATION AND OPERATION

UAP-1783

Safety Compliance Information

Safety Compliance

This equipment complies with:

- CSA C22.2 No. 60950-1-03 / Safety of Information Technology Equipment, Including Electrical Business Equipment.

- UL 60950-1 (1st Edition) / Safety of Information Technology Equipment, Including Electrical Business Equipment.

- IEC 60950-1 (1st Edition) / Safety of Information Technology Equipment, Including Electrical Business Equipment.

CAUTION

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not

perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all

servicing to qualified service personnel. Servicing should be done in a static-free environment.

Electromagnetic Compatibility

- This equipment has been tested for verification of compliance with FCC Part 15, Subpart B, class A requirements for

Digital Devices.

- This equipment complies with the requirements of:

EN 55022 Class A, Electromagnetic Emissions,

EN 61000-3-2 & -3-3, Disturbance in Supply Systems

EN 61000-4-2, -3, -4, -5, -6, -8 & -11 Electromagnetic Immunity

How to contact us:

For technical assistance, please contact the Miranda Technical support centre nearest you:

Americas

Telephone:

+1-800-224-7882

e-mail:

[email protected]

Asia

Telephone:

+81-3-5730-2987

e-mail:

[email protected]

Europe, Middle East,

Africa, UK

Telephone:

+44 (0) 1491 820222

e-mail:

[email protected]

France (only)

Telephone:

+33 (0) 1 55 86 87 88

e-mail:

[email protected]

Visit our web site at www.miranda.com

GUIDE TO INSTALLATION AND OPERATION

UAP-1783

Table of Contents

1UAP-1783 Eight Channel Universal Audio Processor.............................................................1

1.1 Introduction ......................................................................................................................................... 1

1.2 Features .............................................................................................................................................. 1

1.3 Applications......................................................................................................................................... 2

1.4 Functional Block diagram.................................................................................................................... 2

1.5 Card front-edge layout ........................................................................................................................ 2

2Installation ..................................................................................................................................3

2.1 Unpacking ........................................................................................................................................... 3

2.2 Installation in the Densité frame.......................................................................................................... 3

2.2.1 Rear Panel Options................................................................................................................ 3

3Operation ....................................................................................................................................5

3.1 Control options.................................................................................................................................... 5

3.2 Local control using the Densité frame control panel........................................................................... 5

3.2.1 Status LED............................................................................................................................. 6

3.2.2 Menu for local control............................................................................................................. 7

3.3 Remote control using iControl........................................................................................................... 10

3.3.1 Audio Processing ................................................................................................................. 12

3.3.2 Dynamic Processing ............................................................................................................ 14

3.3.3 Audio Output ........................................................................................................................ 16

3.3.4 UP/DOWN MIX .................................................................................................................... 18

3.3.5 Channel Status..................................................................................................................... 21

3.3.6 Audio Type........................................................................................................................... 22

3.3.7 RALM tab: ............................................................................................................................ 23

3.3.8 A-BUS .................................................................................................................................. 24

3.3.9 Reference Input.................................................................................................................... 25

3.3.10 Rear Type ............................................................................................................................ 26

3.3.11 Factory / Presets.................................................................................................................. 26

3.3.12 Options................................................................................................................................. 28

3.3.13 Alarm Configuration .............................................................................................................28

3.3.14 Info ....................................................................................................................................... 29

4Specifications...........................................................................................................................30

GUIDE TO INSTALLATION AND OPERATION

UAP-1783

GUIDE TO INSTALLATION AND OPERATION

UAP-1783 | 1

1 UAP-1783 Eight Channel Universal Audio Processor

1.1 Introduction

The UAP-1783 is an eight-channel high quality audio processor designed to work alone or with a wide

range of video converters, frame synchronizer proc/amps of the Densité series.

The card features two distinct processing blocks: Input and Output. The input processing includes Dolby

detection, Tone generator, delay adjustments, level controls and phase correction. Delay components

include a fixed delay of up to 2 seconds as well as a video tracking delay that will automatically track the

varying saw tooth delay introduced by an associated video frame synchronizer.

The output processing block includes full channel shuffling, an additional gain/attenuation stage and

mixing. Each odd output channel is a mix of any two input channels, and a 4-channel mixing is available

on the even output channels. Additional audio functions such as dynamic processing (compressor/limiter

and expander) and/or Down and Up mixing are available as options.

With a card-to-card Audio bus, the UAP-1783 provides processing for 8 channels originating from a video

card. Once processed, the signals are sent back to be embedded, and are also available at the analog and

digital outputs.

Along with the audio channels, the Audio bus carries the timing, delay signaling and Dolby Metadata.

When combining cards together all audio processing is synchronous and in phase, ensuring proper

alignment and matched delay. The UAP-1783 can work with one video card and/or one other audio

processor card.

User-defined channel identification data may be encoded in the AES status bits. An input audio signal

status is also available indicating the input signal presence or overload.

The card is housed in a (DENSITÉ) frame, with a single or double width rear connector panel. Based on

the rear module installed, the UAP-1783 is compatible with the AES3 or AES-3id digital audio standard.

1.2 Features

•8 channel processing of embedded audio signals.

•Stand-alone 8 channel audio processor and delay.

•Fixed delay and up to 8 video frames tracking delay

•Full channel shuffling on the outputs

•2 and 4 channel mix-down

•Audio metering data for audio levels and phase over IP.

•Dolby E compatibility

•Analog and digital audio inputs and outputs

•Full quality 24 bit audio converters

•Balanced AES3 or unbalanced AES3-id I/Os

•-96 to +12 dB of input and output level adjustments (0.5 dB steps)

•Separate input and output 0 dBFS adjustments (0 to +24 dBu, 1 dB steps)

•Locks to video card, frame reference or AES input

•Internal digital EBU tone generator

•Absence signal delay and threshold adjustable /channel

GUIDE TO INSTALLATION AND OPERATION

2| UAP-1783

•Overload detection

•All settings through frame control panel or remotely

•Status LED and alarms remote reporting

1.3 Applications

•With a DEC-1xxx in Incoming feeds applications as an A to D converter and audio processor.

•Companion to an ENC-1xxx as an audio proc and a final D to A converter.

•Stand-alone or associated with an FRS-1xxx as an audio processor with analog and digital inputs

and outputs.

1.4 Functional Block diagram

1.5 Card front-edge layout

STATUS

SELECT

SW1

Select

Button

Status Led

UAP-1783

ABUS connector

UAP 1783 BLOCK DIAGRAMM

Remote

Control

Select

Status

Monitor

OUT

AES

Outputs

Analog

Inputs

2 x

DIR

SRC

(110/75 Ω)

48 x 16 Schuffler

48 16

Microcontroller

Reference

From DIR1

16 x Overload 8 x Peak meters, 4 x Phase meters

ABUS

VIDEO

Video card / audio cards link

Analog

Outputs

Intra Frame

OUTPUT PROCESSOR

INPUT PROCESSOR

L & R Swap

16 x No Signal

4 x

ADC

4 x Overload

Ref. IN

(110/75 Ω)

ABUS Select

Tone

Dolby Detection

AES

Inputs

Fixed & Variable Delay

Phase & Level

Compressor - Limiter - Expander

Up or Down Mixer

16x Level

4 x

DAC

2 x

DIT

ABUS IN

ABUS OUT

GUIDE TO INSTALLATION AND OPERATION

UAP-1783 | 3

2 Installation

2.1 Unpacking

Make sure you have ordered and received the UAP-1783 and its associated rear panel. If any of the

following items are missing, contact your distributor or Miranda Technologies Inc.

•UAP-1783 8-Channel Universal Audio Processor

•One of the UAP-1783 Rear Panels (see figure)

•An ABUS flat cable

2.2 Installation in the Densité frame

The UAP-1783 must be mounted in a DENSITÉ frame. The installation includes both the UAP-1783

module, and the rear panel module. It is not necessary to switch off the frame’s power when installing or

removing the card.

When the UAP-1783 is used in conjunction with a video module such as FRS-1101 and/or another UAP-

1783, the ABUS flat cable must be installed between the ABUS connectors.

•Note: for a two card installation, use the two end connectors of the flat cable and leave the

middle one unplugged.

Detailed instructions for installing cards and their associated rear panels in the Densité frame are given in

the Densité Frame manual.

2.2.1 Rear Panel Options

Single rear panels AES3 or AES3-id compatible

UAP-1783-DA110-SRP

+ G - + G -

ANALOG OUT

AES IN

+ G -

+ G - + G -

UAP-1783-DA75-SRP

+ G - + G -

ANALOG OUT

AES IN

+ G -

1/DARS

DARS

UAP-1783-AD110-SRP

+ G - + G -

ANALOG IN

AES OUT

+ G -

+ G - + G -

UAP-1783-AD75-SRP

+ G - + G -

ANALOG IN

+ G -

AES OUT

GUIDE TO INSTALLATION AND OPERATION

4| UAP-1783

Dual rear panels AES3 or AES3-id compatible

UAP-1783-AADD110-DRP

ANALOG OUT

+ G - + G -

2 RIGHT

ANALOG IN AES IN

+ G -

1L 2R

+ G - + G -

1/DARS

AES OUT

+ G - + G -

+ G -

UAP-1783-AADD75-DRP

ANALOG OUT

+ G - + G -

2 RIGHT

ANALOG IN AES IN

+ G -

1L 2R

1/DARS

AES OUT

+ G - + G -

+ G -

GUIDE TO INSTALLATION AND OPERATION

UAP-1783 | 5

3 Operation

3.1 Control options

The UAP-1783 has two primary control interfaces:

•The local control panel attached to the Densité frame’s controller

•Remote control using Miranda’s iControl system

These will be explained in detail in the following sections.

3.2 Local control using the Densité frame control panel

Push the SELECT button on UAP-1783 card edge (see Section 1.5) to assign the local control panel to

operate the UAP-1783. Use the control panel buttons to navigate through the menu, as described below.

All of the cards installed in a Densité frame are connected to the frame’s controller card, which handles all

interaction between the cards and the outside world. There are no operating controls located on the cards

themselves. The controller supports remote operation via its Ethernet ports, and local operation using its

integrated control panel.

The local control panel is fastened to the controller

card by a hinged connector, and when installed is

located in the front center of the frame, positioned in

front of the power supplies. The panel consists of a

display unit capable of displaying two lines of text,

each 16 characters in length, and five pushbuttons.

The panel is assigned to operate any card in the frame

by pushing the SELECT button on the front edge of

that card. Pushing the CONTROLLER button on the

control panel selects the Controller card itself. The

STATUS LED on the selected card flashes yellow.

The local control panel displays a menu that can be navigated using the four pushbuttons located beneath

the display. The functionality of the pushbuttons is as follows:

[+] [–] Used for menu navigation and value modification

[SELECT] Gives access to the next menu level. When a parameter value is shown, pushing this button

once enables modification of the value using the [+] and [–] buttons; a second push confirms the

new value

[ESC] Cancels the effect of parameter value changes that have not been confirmed; pushing [ESC]

causes the parameter to revert to its former value.

Pushing [ESC] moves the user back up to the previous menu level. At the main menu, [ESC]

does not exit the menu system. To exit, re-push the [SELECT] button for the card being

controlled.

If no controls are operated for 30 seconds, the controller reverts to its normal standby status, and the

selected card’s STATUS LED reverts to its normal operating mode.

SELECT

ESC

CONTROLLER

GUIDE TO INSTALLATION AND OPERATION

6| UAP-1783

3.2.1 Status LED

The status monitor LED is located on the front card-edge of the UAP-1783, and is visible through the front

access door of the DENSITÉ frame. This multi-color LED indicates module status by color, and by

flashing/steady illumination, according to the chart. The chart also indicates fault reporting for this card on the

DENSITÉ frame’s serial and GPI interfaces.

Serial

Report GPI

Report Green Yellow Red Flashing

Red Flashing

Yellow

Card system error 

-

Not expected reference Error 

-

Reference error 



AES carrier no lock 

-

AES carrier biphase 

-

AES carrier parity 

-

AES carrier CRCC 

-

AES carrier invalid sample 

-

AES PCM presence 

AES Non-PCM presence 

AES Dolby E presence 

AES AC-3 presence 

NSD CH 1 to 4 Analog input 

-

NSD CH 5 to 8 Digital input 

-

NSD CH 9 to 16 (Ext.CH 1/8 or 9/16) 

-

OVERLOAD CH 1 to 4 analog inputs 



OVERLOAD CH 1 to 16 processing 

-

OVERLOAD analog outputs 1 to 4 

OVERLOAD digital outputs 5 to 8 

Any TONE activated 

-

Any output Mute 

-

User attention - - - - - - Yes

Rear panel error - - - - - Yes -

FPGA error - - - - - Yes

: Factory default.

Note: The non-requested message posting to an alarm status can only be accessed by the

communication protocol (serial port)

NOTE: A “Flashing Yellow” Status LED indicates that the SELECT button on the front panel has been

pushed.

Tabla de contenidos

Otros manuales de Hardware de computadora de Miranda

Miranda

Miranda Intuition XG Manual de usuario

Miranda

Miranda DENSITE series DAP-1781 Manual de instrucciones

Miranda

Miranda DENSITE LGK-3901 Guía de inicio rápido

Miranda

Miranda DENSITE series Manual de instrucciones

Miranda

Miranda DENSITE AAP-1741 Manual de instrucciones

Miranda

Miranda Kaleido-X16 Instrucciones de funcionamiento e instalación

Miranda

Miranda Kaleido-Alto Manual de usuario

Miranda

Miranda M848-2705-490 Hoja de datos

Miranda

Miranda Kaleido-Alto Manual de usuario

Miranda

Miranda DENSITE series Manual de instrucciones

Miranda

Miranda Imagestore Intuition+ Manual de usuario

Miranda

Miranda Vertigo XG Hoja de datos

Miranda

Miranda Kaleido-K2 Manual de instrucciones

Miranda

Miranda UVP-101i Manual de instrucciones

Miranda

Miranda Vertigo XG Manual de usuario

Miranda

Miranda M848-9005-470 Hoja de datos

Miranda

Miranda Imagestore Intuition+ Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario