MIMAKI Textile Jet Tx3-1600 Manual de usuario

MIMAKI ENGINEERING CO., LTD.

TKB Gotenyama Building, 5-9-41, Kitashinagawa, Shinagawa-ku, Tokyo 141-0001, Japan

Phone: +81-3-5420-8671 Fax: +81-3-5420-8687

URL: http: // www.mimaki. co. jp /

E-mail: [email protected]

D201026

OPERATION MANUAL

Requests

•This Manual has been carefully prepared for your easy understanding, how-

ever, please do not hesitate to contact a distributor in your district if you have

any inquiry.

•Description contained in this Manual are subject to change without notice for

improvement.

•Generally, names and designations referred to in this Manual are trade marks

or registered trade marks of the manufacturers or suppliers.

Reproduction of this manual is strictly prohibited.

DISCLAIMER OF WARRANTY

THIS LIMITED WARRANTY OF MIMAKI SHALL BE THE SOLE AND EXCLUSIVE

WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IM-

PLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS, AND MIMAKI NEITHER ASSUMES NOR AU-

THORIZES DEALER TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABIL-

ITY OR MAKE ANY OTHER WARRANTY OR MAKE ANY OTHER WARRANTY IN

CONNECTION WITH ANY PRODUCT WITHOUT MIMAKIÅfS PRIOR WRITTEN

CONSENT. IN NO EVENT SHALL MIMAKI BE LIABLE FOR SPECIAL, INCIDEN-

TAL OR CONSEQUENTIAL DAMAGES OR FOR LOSS OF PROFITS OF DEALER

OR CUSTOMERS OF ANY PRODUCT.

INTERFERENCE TO TELEVISIONS AND RADIOS

The product covered by this Instruction Manual produces low radio waves while it is in

operation. The product can interfere with radios and televisions if set up or commissioned

under improper conditions. The product is not guaranteed against any damage to specific-

purpose radio and televisions.

The product’s interference with your radio or television will be checked by turning on/off

the power switch of the product.

In the event that the product is the cause of interference, try to eliminate it by taking one of

the following corrective measures or taking some of them in combination.

•Change the direction of the receiving antenna or the feeder of your

radio/television.

•Change the installing direction of the product.

•Move the receiver away from the product.

•Use a power line for the receiver that is not shared with the prod-

uct.

LASER SAFETY

This Model is certified as a Class I laser product under the U.S. Department of Health and

Human Services Radiation Performance standard according to the Radiation Control for

Health and Safety Act of 1968. This means that this Model does not produce hazardous

laser radiation.

CDRH REGULATION

The Center for Devices and Radiological Health for the U.S. Food and Drug Administration

Implement regulations for laser products. The Label shown below indicates compliance

with the CDRH regulations and is labeled on the product when marketed in the United

States. This Model is equivalent to Class I laser device according to CDRH Regulation.

FCC Statement (USA)

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a commer-

cial environment. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in

which cause the user will be required to correct the interference at his own expense.

•In the case where MIMAKI-recommended cable is not used for

connection of this device, limits provided by FCC rules can

be exceeded. To prevent this, use of MIMAKI-recommended

cable is essential for the connection of this device.

This product complies with 21 CFR chapter I and subchapter J.

- i -

Foreward

Thank you for purchasing MIMAKI Tx3-1600 color inkjet plotter for textile.

Model Tx3-1600 is a color inkjet plotter for printing on fabric with eight different colors at high

speeds.

Read this manual carefully and make the most effective use of your plotter.

•Tx3-1600 is equipped with a high speed print head and other high perfor-

mance part that may be dangerous. Please be sure to read this manual

carefully before starting this plotter operation in order to prevent the

injuries or damages.

•Use of controls, adjustments or performance of procedures other than

those specified in this manual may results in hazardous radiation expo-

sure.

On this Operation Manual

•This operation manual describes the operation and maintenance of Model

Tx3-1600 Color InkJet Plotter (hereinafter referred to as the plotter).

•Please read and fully understand this Operation Manual before putting the

machine into service. It is also necessary to keep this Operation Manual

on hand.

•Make arrangements to deliver this Operation Manual to the person in

charge of the operation of this plotter.

•This Operation Manual has been carefully prepared for your easy under-

standing, however, please do not hesitate to contact a distributor in your

district if you have any inquiry.

•Description contained in this Operation Manual are subject to change

without notice for improvement.

•In the case where this Operation Manual should be illegible due to de-

struction by fire or breakage, purchase another copy of the Operation

Manual from our distributor.

- ii -

Features

The features and methods of operation are explained in this manual for you to understand how to use

the device properly.

Various textile printing ink can be used

MIMAKI genuine ink is shown below.

Acid dye ink : Suitable for wool, silk, and other animal fibers and nylon.

Reactive dye ink : Suitable for wool, silk in addition to cotton, rayon, etc.

Disperse dye ink :Suitable for fibers such as polyester, acrylic etc.

Printing pigment ink :Use with cotton. Fixing with hot pressing is possible in postprocessing.

•When using any type of ink, be sure to perform the pre-processing and

post-processing recommended by MIMAKI for the fabric used.

•Use the printing pigment in an environment with humidity of 40% or more.

Automatic nozzle check function

Checks the print head condition automatically even during printing.

If a failure is detected, this function performs recovery operation, recheck, etc. according to

the setting. This function enables unattended print operation.

Applicability of fabric up to 7 mm in thickness

Even thick fabric, such as boards, can be used.

The plotter accepts fabric whose thickness is in the range of 0.1mm to 7.0mm.

Applicable to wide fabric

Fabric with up to 1650mm width can be set and printing for up to 1620mm width is possible.

Remaining ink management system with Ink IC tip

The IC chip mounted on the ink cartridge allows monitoring of the amount of remaining ink

even after it is removed and remounted.

This avoids INK END during unattended operation, allowing efficient use of ink and fabric.

LCD display

The LCD panel displays the device setting menu in two lines.

Since the LCD panel is provided with a backlight, the display can be seen clearly even in a

dark place. The LCD panel is capable of displaying seven different languages, including

English and Spanish.

- iii -

Large capacity Ink (2 Liters) can be set

Two one-liter ink toggles can be set for each color.

If one toggle runs out, the other toggle is selected automatically to prevent interruption of

printing caused by ink replacement.

Display of information for confirmation

It is possible to have the printing length displayed on the LCD panel and the printing condi-

tions to be plotted for confirmation during operation of the plotter.

High-speed interface

The "IEEE 1394" interface allows for high-speed data reception from the computer.

Take-Up device for printing on a long fabric

Since the take-up device winds up the plotted fabric, along fabric is also available.

Fabric retainer

If the edge of the fabric is curled or raised, the fabric retainer can be used to avoid contact of

the fabric and ink head.

Ditch for penetrated ink

Even with printing to a coarse-textured fabric, the backing fabric is not stained by penetrated

ink. Removable platen boards are prepared for fabric without ink penetration.

Dryer provided

After printing, the dryer dries the fabric on the path up to the take-up device.

Applicable to large rolls

Up to 200m rolls (cotton, t=0.25, approx 38kg) can be set, fed, and rolled up.

Printing on a stretch materials

Enable to print on a stretchy material by sticking the fabric on the belt with a pressure roller.

Cleaning the belt during printing

Enables to print as removing inks or dusts adhered on the belt.

Feed Comp. function has been newly added.

Correcting the medium feed rate during printing.

Support for 4-color plotting

4 colors are allocated to 8 heads to enable plotting.

Plotting using 4 colors takes only half the time as with the 8-color set.

- iv -

For Safe Operation

Pictorial Signs

Pictorial signs are used in this Instruction Manual for safe operation of and in prevention of damages

to the device. Pictorial signs and their meanings are given below. Read and fully understand before

reading the text.

•Indicates the case where it is assumed that misuse of the machine, ignor-

ing this sign, can expose the operator to danger of injury or death.

•Indicates the case where it is assumed that misuse of the machine, ignor-

ing this sign, can cause damage only to property.

•The symbol " " indicates helpful information that will facilitate the use of

the device.

Example of Pictorial Signs

•The symbol " " indicates the case where some phenomenon that re-

quires a CAUTION sign (including "DANGER" and "WARNING" signs)

exists. A concrete precaution (precaution against an electric shock in the

case of the sketch given on the left) is shown in the illustration.

•The symbol " " indicates a prohibited behavior. A concrete illustration of

prohibition (disassembly is prohibited in the sketch given on the left) is

shown in or next to the illustration.

•The symbol " " indicates a thing that is forced to be done and instruction

that is forced to be followed. A concrete illustration of instruction (the

removal of a plug from the receptacle is instructed in the sketch given on

the left) is drawn in the illustration.

- v -

During installation

•The device is as heavy as

approximately 1100 kg.

Perform the installation work

by at least six persons.

Do not disassemble or remodel the device.

• Never disassemble or

remodel the main unit of the

printer and the ink cartridge.

Disassembling/remodeling any

of them will result in electric

shocks or breakdown of the

device.

Do not use the device in damp places.

•Avoid damp environments

when putting the device into

service. Do not splash water

onto the device. High-humidity

or water will give rise to fire,

electric shocks or breakdown

of the device.

Abnormal event occurs.

•If the device is used under an

abnormal condition where the

device produces smoke or

unpleasant smell, fire or

electric shocks can result. Be

sure to turn off the power

switch imfabrictely and detach

the plug from the receptacle.

Check first to be sure that the

device no longer produces

smoke, and contact a

distributor in your district for

repair.

Never repair your device by

yourself since it is very

dangerous for you to do so.

Power supply and voltage

•Be sure to use the device

with the power supply

specifications indicated.

•Be sure to connect the plug

of the power cable to a

grounded receptacle.

If not, fire or electric shocks

can result.

Roll fabric

•Roll fabric is heavy. Be

careful not to drop it. If you

drop it on your foot, or any

other part of your body,

personal injury can result.

Handling of ink cartridges

•Store ink cartridges and

waste ink tank in a place that

is out of the reach of

children.

If ink settles on the skin or

fabric, immediately wash it

off with detergent or water.

In the event that ink gets in

eyes, immediately rinse it off

with water and consult a

medical doctor.

•Neither pound the ink

cartridge nor shake it

violently so as to prevent

leakage of ink.

•Never refill the ink cartridge

with ink. MIMAKI assumes

no responsibility for

malfunction caused by using

the device after

replenishment of ink.

Never Do the Following

WARNING

- vi -

Laser Sensor

•This device is equivalent to

Class I laser device according

to CDRH Regulation. LASER

CAUTION Label for CDRH

regulation shown below is

provided with the device.

Also, the device is equivalent to

a Class I laser device according

to JIS/IEC standard. The label

according to these standards

shown below is provided with

the device.

To avoid causing pain in your

eyes or visual impairment, do

not review the laser beam

through a lens or the other

optical observation system.

Handling of the power cable

•Take care not to damage,

break or work on the power

cable.

If a heavy matter is placed on

the power cable, heated or

drawn, the power cable can

break to cause fire or electric

shocks.

•Connecting the power cable

cannot be installed by the

customer.

Contact your local distributor to

call for service to connect the

power cable as well as moving

installation of the device.

We should take no

responsibility for any troubles

caused through the power

cable connection by the

customer without calling for

service.

Never Do the Following

WARNING

クラス1レーザ製品

Tabla de contenidos

Otros manuales de Impresora de MIMAKI

MIMAKI

MIMAKI JV3-250 SP Manual de usuario

MIMAKI

MIMAKI UJF-7151 plus Manual de usuario

MIMAKI

MIMAKI UJF-7151 plus Manual de usuario

MIMAKI

MIMAKI UJF-605CII Manual de usuario

MIMAKI

MIMAKI JV400-LX Manual de usuario

MIMAKI

MIMAKI JV33-130 Manual de usuario

MIMAKI

MIMAKI UJV55-320 CMYK Manual de usuario

MIMAKI

MIMAKI JV5-130S Manual de usuario

MIMAKI

MIMAKI UCJV300 Manual de usuario

MIMAKI

MIMAKI JV150 Series Manual de usuario

MIMAKI

MIMAKI UJV55-320 CMYK Manual de usuario

MIMAKI

MIMAKI JFX200-2531 Manual de mantenimiento

MIMAKI

MIMAKI UJF-3042MkII EX Manual de usuario

MIMAKI

MIMAKI JV300-130 A Manual de mantenimiento

MIMAKI

MIMAKI Tx300P-1800B Manual de usuario

MIMAKI

MIMAKI JV150-130 Manual de mantenimiento

MIMAKI

MIMAKI TS300P-1800 Manual de mantenimiento

MIMAKI

MIMAKI JV400-SUV Series Manual de usuario

MIMAKI

MIMAKI GP-1810 Manual de usuario

MIMAKI

MIMAKI JV330 Series Manual de mantenimiento

MIMAKI

MIMAKI UJF-3042MkII e Manual de mantenimiento

MIMAKI

MIMAKI UJF-A3MkII Series Manual de usuario

MIMAKI

MIMAKI TxF300-75 Manual de mantenimiento

MIMAKI

MIMAKI UJF-3042HG Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario