MIMAKI UJF-605CII Manual de usuario
MIMAKI ENGINEERING CO., LTD.
TKB Gotenyama Building, 5-9-41, Kitashinagawa, Shinagawa-ku, Tokyo 141-0001, Japan
Phone: +81-3-5420-8671 Fax: +81-3-5420-8687
URL: http: // www.mimaki. co. jp /
E-mail: [email protected]
Daily Care Manual
D201579
Request for daily care
Inkjet printer is the precision machine that has highly delicate mechanism. Especially, little dust and
paper powder may have effect on a head nozzle firing ink, and may not get normal printing.
To use the inkjet printer in good condition, we recommend the following daily care.
2
Table of contents
In Case Sefective Printing Is Not Resolved ............................................ 5
Cleaning Flushing Tray ............................................................................ 8
When The Waste Ink Tank Becomes Full.............................................. 10
Replacing Water In Water Heater Tank ................................................. 11
Regular Maintenance For White Ink ...................................................... 17
Cleaning Or Replacing Filter ................................................................. 19
Cleaning The Undersurface Of The Carriage........................................ 20
Storage Of Antifreezing Liquid And Washing Liquid.............................. 22
Storage Of Media .................................................................................. 22
Storage Of Ink Cartridge ....................................................................... 22
3
Installation environment and Notes on cleaning
•Use this printer in clean (less dust) environment. The use of fan and ventilator might be
cause of dusty environment.
They brow dust up dust around the printer.
•As using UV curing ink, install this printer in a well-ventilated area.
•Working environmental temperature is 15 to 30°C (59 to 86°F). Avoid using at lower or
higher than this.
Notes on cleaning
•Never disassemble the device. Disassembling the device can result in
electric shock hazards and breakage of the device.
•Prevent moisture from entering inside the device. If the inner part of the
device becomes wet, electric shock hazards and breakage of the device
can result.
•Conduct maintenance works after turning off the power switch and detach-
ing the power cable. If not, unexpected troubles can arise.
•Make maintenance after the UV lamp has been sufficiently cooled, or burn
injury may occur.
•Do not use benzine, thinner and chemical agents containing abrasives.
Such materials can deteriorate or deform the surface of the cover.
•Do not apply lubricating oil or the like inside the device. Such materials
can cause the printer mechanism to fail.
•UJF-605C is a printer that uses ultraviolet ray curing ink (UV ink).. When
implementing the daily care, must wear supplied goggles and gloves.
•In case water or alcohol mixed into the organic solvent ink, flocculation
would be occurred. Be sure that not adhere water or alcohol to not only the
nozzle and also near the head, the cap, wiper and so on.
4
Maintenance for frame components
If the frame components of the device have stained, dampen a piece of soft cloth with
water or neutral detergent diluted with water, squeeze it and wipe the frame components
clean.
5
In Case Sefective Printing Is Not Resolved
When the station interior is severely contaminated or defective printing is not resolved
after executing the head cleaning function ( Operation manual P.2-20).
Clean the suction nozzle and cap using the cleaning kit as follows,
Washing liquid, Gloves, Cleaning swab, goggles
•When cleaning the ink station and head, be sure to wear the supplied
goggle and gloves since you may get ink in your eyes.
•Do not use alcohol or water.
•Do not move the carriage out of the capping station by hand. Use the
appropriate operation key to move the carriage.
The examples of defective printing
These following examples indicate improper head (nozzle) firing by dust, which effect
printing. Confirm the nozzle condition periodically before or during outputting not to use in
such as this condition. The nozzle condition can be confirmed with [test print] in this plotter.
Deflection Nozzle out
Ink dropping Satellite
6
STEP
1. Press the [FUNCTION] key from the LO-
CAL mode.
2. Press the [ ] and [ ] keys until the display
gives the indication [MAINTENANCE].
3. Press the [ENTER] key.
4. Press the [ ] and [ ] keys until the display
gives the indication [STATION].
5. Press the [ENTER] key.
6. Press the [ENTER] key again.
Carriage moves to the table.
7. Open the right maintenance cover.
8. Clean the suction nozzle using the exclu-
sive cleaning swab which is containing
washing liquid.
•Carefully clean the suction nozzle.
•Suction nozzle severely contaminated
or bent should be replaced with a new
one. Contact your nearest sales
agency or Mimaki sales office.
•Contact your nearest sales agency or
Mimaki sales office to order the exclu-
sive cleaning swab.
<< LOCAL >>
STATION
CARRIAGE OUT : ent
MAINTENANCE
STATION < ent >
MAINTENANCE
LIST < ent >
FUNCTION
MAINTENANCE < ENT >
FUNCTION
DATA CLEAR < ENT >
7
9. Wipe the adherent ink which got on the
cap rubber or inside the suction nozzle
cover with the exclusive cleaning swab.
10. Close the maintenance cover and then press
the [ENTER] key.
The initial operation is performe, then the device
enters to the LOCAL mode.
How to recover improper nozzle firing
When not using this plotter for a long time or according to environmental temperature,
nozzle may be unstable in firing.
In the case of this, follow below procedures to recover nozzle.
In case the nozzle doesn't recover after implementing these procedures, contact with our
customer service or agency you purchased, and need to replace heads and so on.
1. Daily care
Implement all parts noted on this article.
2. Normal cleaning ( Operation manual
P.2-20)
Implement normal cleaning along the instruction
manual after daily care above-mentioned.
Repeat cleaning and test printing, and confirm the
nozzle still clogging or not.
•In case nozzle clogging is not resolved
with all these procedures, contact with
our customer service or make service
call to the agency you purchased.
Suction nozzle cover
STATION
COMPLETED : ent
PLEASE WAIT
<< LOCAL >>
8
Cleaning Flushing Tray
Wipe off waste ink from the flushing tray.
Tools necessary for cleaning: Washing liquid, Gloves, goggles, paper towel
•When cleaning the ink station and head, be sure to wear the supplied
goggle and gloves since you may get ink in your eyes.
•Do not move the carriage out of the capping station by hand. Use the
appropriate operation key to move the carriage.
•Make sure to remove the waste ink in the flushing tray frequently. Other-
wise the waste ink dried out solidly under the UV light and may not remove.
STEP
1. Press the [FUNCTION] key from the LO-
CAL mode.
2. Press the [ ] and [ ] keys until the display
gives the indication [MAINTENANCE].
3. Press the [ENTER] key.
4. Press the [ ] and [ ] keys until the display
gives the indication [STATION].
5. Press the [ENTER] key.
6. Press the [ENTER] key.
Carriage moves to the table.
<< LOCAL >>
STATION
CARRIAGE OUT : ent
MAINTENANCE
STATION < ent >
MAINTENANCE
LIST < ent >
FUNCTION
MAINTENANCE < ENT >
FUNCTION
DATA CLEAR < ENT >
9
7. Open the left maintenance cover.
8. Wipe off the waste ink from the flushing
tray with the paper towel containing wash-
ing liquid. Take the caked ink off by pat-
ting the tray.
•Make sure to take the caked ink off
completely, or it may cause head
damage by the remaining caked ink.
The UV ink dried out solidly under the
UV light. In case unable to get rid of
the caked ink, the tray should be
replaced with a new one. Please
contact your local dealer for purchas-
ing a new tray.
9. Close the station cover and then press the
[ENTER] key.
The initial operation is performe, then the device
enters to the LOCAL mode.
STATION
COMPLETED : ent
PLEASE WAIT
<< LOCAL >>
10
When The Waste Ink Tank Becomes Full
Waste ink used for cleaning the heads will gather in the waste ink tank.
•Contact your local MIMAKI distributor or call a local MIMAKI office if you
need a spare waste ink tank.
•Prepare a polyethylene tank for emptying waste ink.
•If ink is dripping, wait until it stops dripping.
When the tank is filled with waste ink, the following error message is indicated:
STEP
1. Open the waste ink tank box cover.
2. Pull out the waste ink tank while pressing
it downward.
•When pulling out the waste ink tank,
hold the opening of the waste ink tank
with paper and then slowly pull it out to
prevent waste ink from spattering.
•Before replacing ink, put paper on the
floor to prevent it from being stained
with ink.
3. Dump waste ink into a separate polyethyl-
ene tank.
•Discard the waste ink according to the
local regulations of the area this unit is
used.
4. Put the empty waste ink tank back into the
device.
Close the Waste ink box cover.
•To avoid hurt hands at the corner of
the tank cover, be careful to set the
tank.
5. Press the [ENTER] key to complete the
procedure.
The device enters to the LOCAL mode.
! INK TANK
WASTE TANK FULL
WASTE TANK
TANK READY :ent
<< LOCAL >>
Tabla de contenidos
Otros manuales de Impresora de MIMAKI
MIMAKI
MIMAKI JFX-1631/1615 Plus Manual de usuario
MIMAKI
MIMAKI Tiger600-1800TS Manual de usuario
MIMAKI
MIMAKI JV33-160 Manual de usuario
MIMAKI
MIMAKI TS30-1300 Manual de usuario
MIMAKI
MIMAKI JV5-130S Manual de usuario
MIMAKI
MIMAKI JFX550-2513 Manual de usuario
MIMAKI
MIMAKI JV5-130S Manual de usuario
MIMAKI
MIMAKI SIJ-320UV Manual de mantenimiento
MIMAKI
MIMAKI JV33-260BS Manual de usuario
MIMAKI
MIMAKI UJV55-320 CMYK Manual de usuario
MIMAKI
MIMAKI UJF-605RII Manual de usuario
MIMAKI
MIMAKI JV330 Series Manual de usuario
MIMAKI
MIMAKI JV150-130 Manual de usuario
MIMAKI
MIMAKI JV400-130LX Manual de usuario
MIMAKI
MIMAKI UCJV300 Manual de mantenimiento
MIMAKI
MIMAKI JV5-320DS Manual de usuario
MIMAKI
MIMAKI Tx300P-1800B Manual de usuario
MIMAKI
MIMAKI JV150-130A Manual de mantenimiento
MIMAKI
MIMAKI UJF-3042MkII e Manual de mantenimiento
MIMAKI
MIMAKI TS55-1800 Manual de usuario
