Milltronics EASY AIMER 2 Manual de usuario
EASY AIMER - 2
The Easy Aimer is an accessory device for aiming Milltronics ultrasonic transducers used in process
material level measurement.
Assembly
1. Feed the transducer cable through
the supplied coupling and conduit.
Then assemble the transducer,
coupling and conduit as shown.
If the transducer diameter is
greater than 148 mm ( 5.8" ),
include the customer mounting
plate. If sealing is required,
include the customer gasket.
2. Feed the conduit through the center
hole of the Easy Aimer until the
conduit is at the desired point within
the Easy Aimer (typically midway).
3. Tighten the conduit gland to
secure the conduit and
transducer assembly in place.
4. Install the supplied locknut
as shown, and complete
the conduit installation.
33454380
Rev 1.6
Printed in China
Peterborough, Canada TEL. (705) 745-2431
Arlington, U.S.A. TEL. (817) 277-3543
Worcester, England TEL. +44 1905 450500
Aix En Provence, France TEL. +33 4 42 65 69 00
June 1999
PL - 438
mounting hole - 3 places to suit
M8 or 3/8", 120° apart on 157
mm (6.2") bolt center diameter
angle block binding
screw and clamp
sighting block binding screw
and clamp
ground screw
178 mm
(7")
3/4" NPT or BSP conduit x 300 mm
(12") long
conduit gland angle block
sighting block
mounting block
customer gasket
(as required)
customer mounting plate
(as required)
coupling (typical)
76 mm (3")
nominal
Milltronics transducer
(typical)
20°
12.7mm
(0.5")
127 mm
(5") Ø
(typical)
locknut
Application
In solids applications, the transducer is generally mounted so that it is aimed toward the low level draw point.
The sighting block can be rotated through 360° with the transducer angled at 0 to 20° off vertical.
The location of the Easy Aimer should be such that the transducer’s sound path is unobstructed and
away from fill points.
The Easy Aimer is capable of withstanding 100 kPa (1 bar or 15 psi) gauge pressure with proper installation and has a
temperature rating from -40oC to 105oC (-40oF to 220oF).
The Easy Aimer must be mounted to an access plate with welded studs or to a flange in order to isolate the
mounting holes from the pressurized environment.
Installation and Aiming
1. Install the Easy Aimer and transducer assembly by bolting the mounting block directly to the bin or via
a mounting plate.
2. Leaving the sighting block binding screws fastened, loosen the angle block binding screws. Rotate the
angle block until the transducer is pointing at the desired angle.
Re-fasten angle block binding screws.
3. Loosen the sighting block binding screws and rotate sighting block until the transducer is pointing in
the desired direction. Sighting reference graduations on the mounting block are 30° apart.
Re-fasten sighting block binding screws.
conduit gland
tighten to 95 N-m
(70 ft lb) of torque
Peterborough, Canada TEL. (705) 745-2431
Arlington, U.S.A. TEL. (817) 277-3543
Worcester, England TEL. +44 1905 450500
Aix En Provence, France TEL. +33 4 42 65 69 00
basic installation
angle adjustment
sighting adjustment
mounting plate
and hardware
(customer supplied)
block binding
screws, 6 places,
tighten to 12 N-m
(9 ft lb) of torque
recommended gasket
thickness
1.5mm - 1.8mm
(.06" - .07")
(customer supplied)
mounting plate with
welded studs
(customer supplied)
mounting
hardware,
3 places, tighten
to 27 N-m
(20 ft lb) of torque
sealed installation
*7ML19981DV01*
Otros manuales de Transductor de Milltronics
Milltronics
Milltronics ST-50 Series Manual de usuario
Milltronics
Milltronics XPS-10 Manual de usuario
Milltronics
Milltronics XLS Series Manual de usuario
Milltronics
Milltronics XRS-5 Manual de usuario
Milltronics
Milltronics PL-521 Manual de usuario
Milltronics
Milltronics ST-100 SERIES Manual de usuario
Milltronics
Milltronics PL-590 Manual de usuario
Milltronics
Milltronics PL-551 Manual de usuario
Manuales populares de Transductor de otras marcas
Mianyang Weibo Electronic
Mianyang Weibo Electronic WB Series Manual de usuario
ProMinent
ProMinent Dulcometer DMT Manual de usuario
MKS
MKS MicroPirani 925 Series Cómo utilizar
WIKA
WIKA WU-20 Manual de usuario
Alcatel Vacuum Technology
Alcatel Vacuum Technology BARATRON 622A Manual de usuario
Camille Bauer
Camille Bauer SIRAX CH-5610 Manual de usuario
