Milestone pro MP-SUH43-KVM Manual de usuario
MP-SUH43-KVM
18G 4x3 VC Switcher w/ Charging
All Rights Reserved
Version: MP-SUH43-KVM_2023V1.0
User Manual
Table of Contents
1. Product Introduction....................................................................................................1
1.1 Features ............................................................................................................1
1.2 Package List ......................................................................................................2
2. Specification ...............................................................................................................3
3. Panel Description........................................................................................................4
3.1 Front Panel ........................................................................................................4
3.2 Rear Panel.........................................................................................................5
4. Video Mode.................................................................................................................6
4.1 BYOM Mode ......................................................................................................6
4.2 Standard Mode ..................................................................................................7
5. Switching Mode ..........................................................................................................8
5.1 Manual Switching ..............................................................................................8
5.2 Auto Switching ...................................................................................................8
6. GUI Control.................................................................................................................9
6.1 Manage Page ..................................................................................................10
6.2 Schedule..........................................................................................................11
6.3 Network Setting ...............................................................................................11
6.4 System Setting ................................................................................................12
6.5 GUI Upgrade ...................................................................................................13
7. EDID Switch..............................................................................................................14
8. RS232.......................................................................................................................15
8.1 RS232 CONTROL COMMANDS .....................................................................16
9. Firmware Upgrade ....................................................................................................24
1. Product Introduction
Thanks for choosing the MP-SUH43-KVM HDMI 2.0 Web-Conferencing Room Switcher!
The matrix switcher simplifies meeting room and presentation space system integration
by providing two video mode (BYOM mode and Standard mode) with three HDMI inputs,
one USB-C input and three HDMI output. The USB-C input supports video, data (USB
host) and power charging up to 60w. There is a 4 port USB client hub built with 3 USB
host ports that can be switched independently.
The matrix switcher supports resolution up to 4K@60Hz@4:4:4, is HDCP 2.2 compliant
and has a built in USB 3.0 switching hub for control and integration of USB devices such
as USB cameras and microphones.
The matrix switcher supports auto switching, allows users to control the system
functionality via TCP/IP, Digital I/O, contact and front panel.
1.1 Features
⚫HDMI 2.0 and HDCP 2.2 compliant.
⚫Video resolution up to 4K@60Hz 4:4:4, 8bit deep color.
⚫Supports auto switching.
⚫USB-C input supports power charging up to 60w.
⚫Provides an audio output for audio de-embedding.
⚫Automatically switch between the dedicated room system and bring your own
meeting (BYOM). Supports audio output volume control.
⚫Use the same Laptop cable between wired screen sharing and bring your own
meetings.
⚫Send CEC signals to the room displays via events and built-in scheduler.
⚫Supports EDID management.
⚫Occupancy sensor integration.
⚫Controllable via TCP/IP, Digital I/O, contact and front panel.
1.2 Package List
⚫1x MP-SUH43-KVM
⚫4x Mounting Ear Screws
⚫4x Plastic Cushions
⚫1x RS232 Cable (USB-A to Mini-USB)
⚫1x Power Adaptor (24V DC 5A)
⚫1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.
2. Specification
Video Input
Video Input
(3) HDMI, (1) USB-C
Video Input Connector
(3) Type-A female HDMI, (1) USB-C
Video input Video Resolution
Up to 4K@60Hz 4:4:4, HDR
Video Output
Video Output
(3) HDMI
Video Output Connector
(3) Type-A Female HDMI
Video output Video Resolution
HDMI: Up to 4K@60Hz 4:4:4, HDR
Audio Output
Audio Output
(1) AUDIO OUT
Audio Output Connector
(1) 3.5mm Jack
Frequency Response
20Hz to 20kHz, ±3dB
Max Output Level
2.2 ±0.1Vrms
THD+N
< 0.1%, 20Hz to 20kHz bandwidth, 1 kHz sine at 0dBFS level (or
max level)
SNR
> 80dB, 20Hz to 20kHz bandwidth
Crosstalk Isolation
< -70 dB, 10kHz sine at 0dBFS level
L-R Level Deviation
< 0.3 dB, 1kHz sine at 0dBFS level (or max level before clipping)
Output Load Capability
1kΩ and higher (supports 10x paralleled 10KΩ loads)
Noise Level
- 75dB
Control Part
Control Port
(1) TCP/IP, (1) FIRMWARE, (1) Digital I/O (1) Contact, (2) USB
Host, (4) USB Device
Control Connector
(1) RJ45, (1) Mini-USB, (2) 3-pin terminal blocks, (2) Type-B USB,
(4) Type-B USB
General
HDMI Version
Up to 2.0
HDCP Version
Up to 2.2
Bandwidth
18Gbps
Operation Temperature
-5 to +55℃(+23°to +131°F)
Storage Temperature
-25 to +70℃(-13°to +158°F)
Relative Humidity
10% to 90%, Non-condensing
External Power Supply
24V DC 5A
Power Consumption
70W (Max)
Dimension (W*H*D)
220mm x 25mm x 110mm
Net Weight
0.55KG
3. Panel Description
3.1 Front Panel
①MODE: A mode switch to select auto/manual switching.
⚫AUTO: The unit will automatically switch between BYOM and STANDARD
mode by detecting input signals.
⚫MANUAL: User can select BYOM or STANDARD mode manually. CONTACT
1 trigger for BYOM mode and CONTACT 2 trigger for STANDARD mode by
default.
②BYOM IN: BYOM IN inputs will work when BYOM mode is selected.
⚫HDMI IN: Connects to HDMI source device for audio and video signal.
⚫USB-C: Connects to USB-C source device for audio, video, USB signal and
up to 60w power delivery.
⚫USB-B: Connects to USB host, work with HDMI IN to transmit USB signal to
the source device.
③ROOM PC IN: ROOM PC IN inputs will work when STANDARD mode is selected.
⚫HDMI IN: Connects to HDMI source device for audio and video signal.
⚫USB-B: Connects to USB host, work with HDMI IN to transmit USB signal to
the source device.
④CONTROL: Control ports to control the unit.
⚫FW: Mini-USB port for RS232 control, normally for firmware upgrade.
⚫DIGITAL I/O: connects to the sensor, supporting 5V or 12V power for the
sensor.
⚫CONTACT: 2 contact ports to trigger events.
⑤DC 24V:
⚫Locking power supply port.
3.2 Rear Panel
①TCP/IP: Connects to the LAN to control the switcher by Web GUI.
②DEVICES: 4 port USB3.0 client hub.
③DISPLAY OUT: 2 HDMI output ports.
④SHARE OUT: 1 HDMI output port.
⑤AUDIO OUT: Connects to audio playback device for audio de-embedding.
⑥EDID: DIP switch to select EDID.
⑦RESET: Button to reset the unit.
4. Video Mode
4.1 BYOM Mode
BYOM (Bring Your Own Meeting) mode allows users to bring their own device to
meeting.
1) USB-C or HDMI of LAPTOP IN will switch to 2 HDMI outputs of DISPLAY OUT.
2) USB devices will switch to the USB Host of LAPTOP-IN (USB-B port if HDMI
source is using and USB-C port if USB-C source is using).
3) Audio output will de-embedded from USB-C or HDMI of LAPTOP IN.
Note: HDMI signal will be selected if both USB-C and HDMI of LAPTOP IN are
connected.
4.2 Standard Mode
1) 2 HDMI inputs of ROOM PC-IN will switch to DISPLAY separately. USB-C or HDMI
of LAPTOP IN will switch to SHARE OUT.
2) USB devices will switch to the USB-B Host of ROOM PC-IN.
3) Audio output will de-embedded from HDMI 1 of ROOM PC-IN.
5. Switching Mode
5.1 Manual Switching
When the DIP switch of rear panel is selected to MANUAL, the switcher is in manual
switching mode. User can select BYOM or STANDARD mode via Web GUI manually.
5.2 Auto Switching
When the DIP switch of rear panel is selected to AUTO, the switcher is in auto-
switching mode. BYOM or STANDARD mode will be automatically selected by signal
detected according to the following rules:
1) If the USB-C or USB-B signal of LAPTOP IN is detected, BYOM mode is selected.
2) If none of the USB-C or USB-B signal of LAPTOP IN is detected, STANDARD
mode is selected.
Tabla de contenidos
Otros manuales de Cambiar de Milestone pro
Milestone pro
Milestone pro MP-SC-41BYOD Manual de usuario
Milestone pro
Milestone pro MP-SUH4ARC-4K Manual de usuario
Milestone pro
Milestone pro MP-SU21T-KVM Manual de usuario
Milestone pro
Milestone pro MP-SC-5T Manual de usuario
Milestone pro
Milestone pro MP-SUH41MV Manual de usuario
Milestone pro
Milestone pro MP-SC-5TDS Manual de usuario
Milestone pro
Milestone pro MP-SC-12D-TN Manual de usuario
Milestone pro
Milestone pro MP-SC-42T-CODEC Manual de usuario
Milestone pro
Milestone pro MP-HD-44A-E Kit Manual de usuario
Milestone pro
Milestone pro MP-SC-61E Manual de usuario
