Miles Industries 541BPC Instrucciones de instalación

4001165-06

Note: This kit must be installed or serviced by a qualiﬁed

installer, service agency or gas supplier. These instructions

are to be used in conjunction with the main installation

instructions for the above listed heater model.

WARNING: If the information in these instructions is not

followed exactly, a ﬁre or explosion may result causing

property damage, personal injury or loss of life.

FOR INSTALLATION WITH A VALOR 530 ENGINE READ THE

FOLLOWING INSTRUCTIONS.

FOR 530 ENGINE CONFIGURATIONS AND VENTING, REFER TO MAIN

INSTALLATION BOOKLET SUPPLIED WITH THE ENGINE.

PORTRAIT

Bolero Cast Front

541BPC

Approved for use with Valor heater model 530 only

Installation and Owner’s Manual

INSTALLER

Leave this manual

with the appliance.

CONSUMER

Retain this manual

for future reference.

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

WARNING

A barrier designed to reduce the risk of burns from the hot viewing

glass is provided with this appliance and shall be installed

for the protection of children and other at-risk individuals.

Casting Tolerances

Due to the nature of cast iron, dimensional consistency

may vary from one unit to the next and some variation

in surface ﬁnish and ﬂatness is to be expected. We

have done our best to control and make allowance for

this; however some variation is inevitable.

Applications

The Valor model 530 heater with the 541BPC Bolero

Front comes ready for installation as a zero clearance

unit into combustible type framing, without need for a

separate zero clearance kit. The 530 installed without

the standard zero clearance stand-off spacers may also

be installed into existing solid-fuel burning ﬁreplaces

provided space and local codes permit.

Hearth Requirements

A 7/8” high plinth is supplied to raise the heater and

ensure a base at the proper height for the cast front to

sit on regardless of ﬂoor ﬁnish height. If not using the

plinth supplied, you MUST make allowance for ﬂoor

ﬁnish and raise (shim) the heater up so the bottom

of the heater sits at the ﬁnished ﬂoor/hearth height,

otherwise, the cast front will not sit at the proper height.

A non-combustible hearth is not required in front of this

appliance.

Kit Contents

1 Cast Frame Assembly ﬁtted

with Barrier Screen

1 Top Bafﬂe

2 Mounting Hooks

1 Framing Plate

1 Plinth

1 Rear Base Support

1 ZC Stand-off LH

1 ZC Stand-off RH

1 Insulation Layer

1 Pack of screws

Floor Requirements

The 530 heater is approved for installation directly

on any combustible material other than soft ﬂooring

material such as carpet or vinyl.

Mantel Requirements

The 541BPC Bolero Front may be installed with

combustible mantels provided clearances are

maintained as indicated in the Dimensions and

Clearances, and Framing diagrams below and on

the following page. Be aware that although safe,

some combustible materials and ﬁnishes at the

listed clearances may, over time, discolor, warp, or

show cracks. Care should be taken when choosing

materials—consult your ﬁreplace dealer.

Insulation

Layer

Stand-offs (2)

Top Baffle

Hooks

Cast Front

Barrier Screen

Framing Plate

w/brackets

Plinth

Rear Base

Support

12”

10”

1” max.

1/2” min.

5”

6-5/8”

dia. 3”

Mantel

leg

See table

Plinth

(optional) E

26”

7/8” High

Raised

Plinth

Top

Outlet

Mantel

‘X’

ZC Stand-os

12”

10”

3”

Framing

Plate

Min. 36” to

combustible

materials

1”

‘Y’ Insul.

31-1/4”

25-1/4”

21-5/8”

5-1/2” to knob

7/8” High

Raised Plinth

26-1/4”

20”

29”

(cast front)

31-1/4”

(framing plate)

23-1/4”

(framing plate)

(cast front)

26”

Dimensions & Clearances

Mantel depth “X” Min. clearance “Y”

1”– 6” 33”

7”– 8” 34”

9” – 12” 38”

12” + 38” + 1” for every

inch beyond 12”

Mantel leg

projection “D”

Min. clearance from

appliance side “E”

Up to 8” 0”

More than 8” 6”

Framing

The 541BPC Bolero Front comes

supplied with a framing plate for zero

clearance applications. The framing

plate is painted black and may be left

exposed beyond the perimeter of the

cast iron front or may be covered with

non-combustible material if desirable.

• A non-combustible hearth is not

necessary in front of this appliance.

• The appliance is approved to install

directly on wood sub-ﬂooring.

• Any framing construction must be

clear of stand-offs.

• Be aware that the area of 7½” x 26¼”

(19 cm x 67 cm) immediately above

the framing plate must be constructed

with non-combustible materials as

shown in ﬁgures.

non-combustible finish

and backing required

Tighten screws after wall finish

to pull brackets tight

Cast Front

Framing Plate

Cover brackets

Cover Framing Plate

up to holes

Wall Finish

(note: any material

covering framing plate

or within 7-1/2”at top

must be non-combust.

non-combustible finish

& backing required

Mount Brackets to Heater

Install Framing Plate

flush with framing or

butt drywall to plate

and run finish over plate

Raised plinth

not shown

Framing Plate

Header Location for

Rear Vent Installations

Brackets Screwed tight

to Plate

Wall Finish

Combustible or

non-combustible

Framing Plate Protudes

by desired wall finish

thickness

Bend Tabs out

for desired wall

finish thickness

Tab Detail

Cast Front

Covers Brackets

Non-Combust.

Mat’l only

Above

Framing Plate

Raised plinth

not shown

Framing plate exposed

Framing plate covered

Top of finished

hearth or floor

Wall Finish

26-1/4”

31-1/2”

to header &

wall finish

(includes

plinth -

reduce by

7/8”if not

using plinth)

7-1/2”

minimum

This part of wall

must be

non-combustible

(cement board or

similar)

Minimum 12”

(Allow extra for rear vent elbows)

Top of finished

hearth or floor

Wall Finish

Note: Header

is raised to

accomodate top

vent clearances

39”

to header

(includes

plinth;

reduce by

7/8”if not

using plinth)

31-1/2”

to header

(includes

plinth;

reduce by

7/8”if not

using plinth)

7-1/2” minimum

This part of

wall must be

non-combustible

(cement board

or similar)

Minimum 12” 26-1/4”

Rear vent framing

Top vent framing

Installation

1. Fit the top bafﬂe under the top panel of the

appliance case. Secure with 2 thread forming

screws.

2. Fit the stand-off spacers. The stand-off spacers for

these installations are supplied ﬂat. These spacers

are left and right handed.

! Warning: Failure to install the stand-off spacers

may result in a ﬁre hazard.

a) Remove the 2 screws near each of the rear top

corners of the appliance and the 2 screws near

the rear top of each side.

b) Bend the spacers as shown.

c) Screw the spacers to the rear of the appliance

using the screws just removed.

d) Bend the side wings of the spacers to align the 2

holes in each spacer with those in the appliance

sides. Secure the spacers using the screws just

removed.

Install top baffle

offsetting

downwards

Heater

3. Mount the framing plate to the appliance.

4. Secure the framing

plate and brackets

to the sides of the

appliance case with

4 thread cutting

screws supplied.

Screw from the

outside through the

access holes in the

framing plate.

Note: There are

alternate methods of

ﬁnishing around the

framing plate—either

leaving it exposed

or recessing it and

covering it up with

the wall ﬁnish. See

page 4.

5. Install plinth and rear base support below ﬁrebox

(optional).

The purpose of the plinth is to allow the appliance

to be placed on a rough subﬂoor, such as plywood,

without regard for the additional thickness of ﬂoor

ﬁnishes as the appliance bottom must otherwise be

placed at the ﬁnished hearth height or the front trims

will not ﬁt on the appliance properly.

a) Detach the burner module from the appliance by

removing its 11 screws.

4”

(102 mm)

total

insulation

Cut out insulation

for top vent installation

Pull forward to expose

width of 5”

b) Fit the rear base support under the rear of the

appliance attaching it to the appliance back

panel with 2 x 3/8” thread cutting (pointed end)

screws.

c) Fit the front plinth under the appliance front with

2 thread forming screws.

6. Install top insulation layer. For top vent outlet

appliances, cut out a circle at the center of the

insulation layer for the vent collar. Place the

insulation layer on top of the appliance case inboard

of the stand-off spacers.

Warning: Failure to install the insulation layer

may cause a ﬁre hazard and voids warranty.

7. If the hooks have been shipped loose with the cast

front, ﬁx them to the front at its top corners.

8. Install the barrier screen by pushing in the bottom

ﬁrst to hook the clips to the frame, sliding it down

behind the fender and pushing the top in so the clips

snap into place.

space between

the edge of screen

and hook is larger

at the top than at

the bottom

top

bottom

front view

Cleaning

To clean the barrier screen use a soft brush. To clean

the polished cast front, use mild soap and water.

If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this

appliance.

To clean the ﬁreplace glass window, refer to the

owner’s manual supplied with the appliance.

DO NOT clean the glass with ammonia.

Removing the front unit

1. Remove the barrier screen by ﬁrst pulling out the top

of the screen and then unhooking the bottom.

2. Unhook the cast front. Lift it up by holding the

louvres. DO NOT lift by holding the top.

Always securely replace the window, the front

and the barrier screen before lighting.

WARNING

FOR YOUR SAFETY, ensure the barrier

screen is reinstalled on the fireplace

after maintenance.

WARNING

DO NOT TOUCH THE BARRIER SCREEN,

THE CAST FRONT OR THE GLASS WHILE

THEY ARE HOT!

Let the fireplace cool first

before cleaning it.

Repairs Parts List # Description Number Alternate no.

1 Ashpan Door 4000465 4000465

2 Cast Fender 4000468 4000468

3 Lower Shield 4000503BY 4000503BY

4 Cast Frame 4000466 4000466

5 Upper Cast Louvre 4000467 4000467

6 Mounting Hooks, Spacers & hardware (2) 4001209 4001209

7 Top Bafﬂe 4000484BY 4000484BY

8 Rear Base Support 569079 340B236

9 Plinth 569059 350K967

10 Framing Plate 4000469 4000469

11 Heater Mounting Bracket (2) 4000488 4000488

12 ZC Stand-off LH 569039 340B235

13 ZC Stand-off RH 569029 340B234

14 Insulation Layer 569049 620B987

15 Barrier Screen 4003289 4003289

Designed and Manufactured by / for

Miles Industries Ltd.

190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1

Tel. 604-984-3496 Fax 604-984-0246

www.valorﬁreplaces.com

Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication.

POUR INSTALLATION AVEC LE FOYER VALOR 530, SUIVEZ LES

DIRECTIVES AUX PAGES SUIVANTES.

POUR LA CONFIGURATION ET L’ÉVACUATION DU FOYER, CONSULTEZ

LE GUIDE D’INSTALLATION FOURNI AVEC LE FOYER VALOR 530.

Note: Ce kit doit être installé ou réparé par un installateur qualiﬁé,

une agence de service certiﬁée ou un fournisseur de gaz. Ces

instructions doivent être utilisées conjointement avec les instructions

d’installation des modèles de foyers Valor indiqués ci-dessus.

MISE EN GARDE: Si les instructions fournies dans le

présent manuel ne sont pas suivies à la lettre, un feu ou

une explosion pourraient résulter et causer des dommages

matériels, des blessures ou la mort.

PORTRAIT

Devanture de fonte Bolero

541BPC

Homologuée par la CSA pour utilisation exclusive avec les foyer Valor 530

Guide d’installation et du consommateur

LE PREMIER

FOYER À GAZ RADIANT

INSTALLATEUR : Laissez cette notice avec l’appareil.

CONSOMMATEUR : Conservez cette notice pour consultation ultérieure.

UNE SURFACE VITRÉE CHAUDE PEUT

CAUSER DES BRÛLURES.

LAISSEZ REFROIDIR LA SURFACE VITRÉE

AVANT D’Y TOUCHER.

NE PERMETTEZ JAMAIS À UN ENFANT

DE TOUCHER LA SURFACE VITRÉE.

AVERTISSEMENT

Une grille de protection conçue pour réduire les risques de brûlures sur la vitre

chaude de la fenêtre est fournie avec cet appareil et doit être installée pour la

protection des enfants et autres individus à risques.

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios para chimeneas de Miles Industries

Miles Industries

Miles Industries Valor Vogue Series Instrucciones de instalación y funcionamiento

Miles Industries

Miles Industries 781RSK Manual de usuario

Miles Industries

Miles Industries 1500I Manual de usuario

Miles Industries

Miles Industries Valor LEGEND G4 780JN Instrucciones de instalación

Miles Industries

Miles Industries Ventana Manual de usuario

Miles Industries

Miles Industries Valor RBWSK Manual de usuario

Miles Industries

Miles Industries Valor 795CFKV2 Manual de usuario

Miles Industries

Miles Industries Valor VOGUE 1345RGP Manual de usuario

Miles Industries

Miles Industries 700I Manual de usuario

Miles Industries

Miles Industries 799EDF Manual de usuario

Manuales populares de Accesorios para chimeneas de otras marcas

Valor

Valor L2 1700K Manual de usuario

Exodraft

Exodraft Xzense Manual de usuario

Whalen

Whalen Ruso MNFP62BF23-6 Manual de usuario

Lopi

Lopi Hearthview 864 Manual de usuario

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manual de usuario

EdilKamin

EdilKamin SERBATOIO 250 Guía de inicio rápido

Bronpi

Bronpi KIT-1 Manual de usuario

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manual de usuario

Travis Industries

Travis Industries 33 DVI Manual de usuario

Superior

Superior ASD3628-TI Manual de usuario

pleasant hearth

pleasant hearth OFP28WG Manual de usuario

IHP

IHP Astria Series Manual de usuario

Firegear

Firegear FG-H-2110SS Manual de usuario

Nibe

Nibe Contura C i31 Manual de usuario

kozy heat

kozy heat KZK-052 Manual de usuario

SimpliFire

SimpliFire SF-WM36 Manual de usuario

Bluegrass Living

Bluegrass Living BC18NR Guía de inicio rápido

pleasant hearth

pleasant hearth IRIS SCROLL Manual de usuario