MikroTik LHG 60G Manual de usuario
1.
2.
3.
LHG 60G
The LHG 60G device works in the 60 GHz wireless spectrum, the operating temperature of these devices is from -40 up to +70 . Each device has one °C °C
gigabit Ethernet port and can be powered with PoE.
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.
The Installation of the equipment must comply with local and national electrical codes.
This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the
correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.
This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate
measures.
Quickstart
Assemble unit. Please see the section.Assembly
Open the Ethernet door to connect an Ethernet cable to the Ethernet port, connect the other end of the Ethernet cable to the included PoE injector.
Plug the PoE injector into your network switch or ISP internet outlet.
Plug the included power supply into the PoE injector to start up the device.
Mount on the mast or pole. Please see the section.Mounting
Set LAN computer IP configuration to (DHCP).
automatic
Once connected to the wireless network, open in your web browser to start configuration, user name: Admin and there is no https://192.168.88.1
password by default.
We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best
performance and stability.
Choose your country, to apply country regulation settings and set up your password on the screen that loads.
Assembly
Attach the two legs to the LHG case.
Snap the assembled LHG unit to the grid in the appropriate locations.
Fix the legs in place with two self thread screws (Use Phillips screwdriver PH2).
Mounting
Attach the mounting assembly to the back of the device with four provided screws. For more details please visit https://i.mt.lv/cdn/rb_files
/Ilustrated_mounting_guide_for_LHG-180704095554.pdf
Mount assembled unit to the pole using provided U bolt clamp. Clamping diameter with the provided steel clamp is 35 – 70 mm.
1.
2.
3.
Use the Aim tool to adjust your device. Please see the section LED status.
The device includes a grounding connection (marked ) which you should connect to the grounding installation of the tower or building where the device will
be used. This is to substantially reduce the risk of ESD and lightning damage. Grounding connector included in the package.
Extension slots and ports
One Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or cross-over cables for
connecting to other network devices.
WiGig, 802.11ad.
Powering
The devices accept powering from the Ethernet port. The Ethernet port accepts PoE input 12-57 V DC (passive and 802.3af/at). A power adapter and a
passive PoE injector are included in the box. When using the PoE injector, make sure to use the "Power + Data" connector to connect to the device, and
the "Data" connector to your PC, router or switch.
Connecting to a POE Adapter:
Connect the Ethernet cable from the device to the POE+DATA port of the POE adapter.
Connect an Ethernet cable from your local network (LAN) to the POE adapter.
Connect the power cord to the adapter, and then plug the power cord into a power outlet.
Maximum power consumption 5 W.
Configuration
We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best performance and
stability. RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself
accustomed to the possibilities: . In case the IP connection is not available, the Winbox tool ( ) can be used to connect https://mt.lv/help https://mt.lv/winbox
to the MAC address of the device from the LAN side.
Please get yourself familiar with additional information on this interface: https://wiki.mikrotik.com/wiki/Manual:Interface/W60G
For recovery purposes, it is possible to boot the device for reinstallation, see section .Buttons and jumpers
Buttons and jumpers
The routerBOOT reset button has the following functions. Press the button and apply the power, then:
Release the button when green LED starts flashing, to reset RouterOS configuration to defaults.
Warning! This equipment should be installed and operated with a minimum distance of 95 cm between the device and your body. Operation of
this equipment in the residential environment could cause radio interference.
The IP rating scale for this device is IP54.
Mounting and configuration of this device should be done by a qualified person.
Release the button when the LED turns solid green to clear all configuration and defaults.
Release the button after LED is no longer lit (~20 seconds) to cause the device to look for Netinstall servers (required for reinstalling RouterOS
over the network).
Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.
Useful for RouterBOOT debugging and recovery.
LED status
The device includes precise alignment guides using LEDs. The lights indicate with arrows direction to turn the dish if looking from behind the dish to the
other end of the link. When alignment LEDs turn off, leaving only the "link established" LED, it means alignment is complete. The LED lights are:
Tilt-up.
Tilt down.
Rotate to right.
Rotate to left.
LED on when the link established.
LED on when Ethernet connected.
User-configurable LED.
Power state on.
Accessories
Package includes the following accessories that come with the device:
K-LHG screw set/fastening set.
Gigabit POE injector.
LHG-5G-390 mm Dish (mesh size 0.5 t x1.0 wx1.4 mm ).
EU/US Switching Power Supply 24 V , 0.38 A, 9 W, Level VI, cable:1.5 m.
Hose Clamp SUS304 (Philips type; clamping diameter range 35-70 mm).
BRAC1_ LHG montage element.
DynaDish U-Bolt M8 (A2 Stainless Steel).
QuickMount AIM.
Specifications
For more information about LHG products, specifications and pictures please visit our web page: https://mikrotik.com/product/lhg_60g
Operating system support
The device supports RouterOS software version 6. The specific factory-installed version number is indicated in the RouterOS menu /system resource.
Other operating systems have not been tested.
MikroTik mobile app
Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point. Scan
QR code and choose your preferred OS.
Federal Communication Commission interference statement
Model FCCID
RBLHGG-60ad TV7LHGG60AD
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a commercial installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device
and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter.
IMPORTANT: Exposure to Radio Frequency Radiation.
95 cm minimum distance has to be maintained between the antenna and the occupational user/general public. Under such configuration, the FCC
radiation exposure limits set forth for an population/uncontrolled environment can be satisfied.
This device meets the Maximum TX power limit per ETSI regulations. The frequency and the maximum transmitted power in EU are listed
below: 57-66GHz: 34.92 dBm. An Operational mode in the 60 GHz band: 58.32 GHz, 60.48 GHz, 62.64 GHz. This device is certified for outdoor
use in Point to Multipoint applications. In the following countries this device cannot be used in Fixed Point-to-Point applications:
Antenna Installation. WARNING: It is the installer's responsibility to ensure that when using the authorized antennas in the United States (or where FCC
rules apply); only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly
forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure the output power level of antennas, according to country
regulations and per antenna type. Professional installation is required of equipment with connectors to ensure compliance with health and safety issues.
Innovation, Science and Economic Development Canada
Model IC
RBLHGG-60ad 7442A-LHGG60AD
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi,
meme si le brouillage est susceptible d'en compromettre le fonctionnement.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-003 (A) / NMB-003 (A)
This device is not to be operated on aircraft except for the conditions listed on ISED RSS-210 Annex J.1.
Cet appareil ne doit pas être utilisé sur un avion, sauf dans les conditions énumérées ISED RSS-210 Annex J.1.
IMPORTANT NOTE: IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 95 cm between the radiator & your body.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé
et utilisé avec un minimum de 95 cm de distance entre la source de rayonnement et votre corps.
UKCA marking
Eurasian Conformity Mark
Информация о дате изготовления устройства указана в конце серийного номера на его наклейке через дробь. Первая цифра означает номер
года (последняя цифра года), две последующие означают номер недели.
Изготовитель: Mikrotikls SIA, Aizkraukles iela 23, Riga, LV-1006, Латвия, [email protected]. Сделано в Китае, Латвии или Литве. Cм. на
упаковке.
Для получения подробных сведений о гарантийном обслуживании обратитесь к продавцу. Информация об импортерах продукции MikroTik в
Российскую Федерацию: https://mikrotik.com/buy/europe/russia
Продукты MikroTik, которые поставляются в Евразийский таможенный союз, оцениваются с учетом соответствующих требований и помечены
знаком EAC, как показано ниже:
Norma Oficial Mexicana
EFICIENCIA ENERGETICA CUMPLE CON LA NOM-029-ENER-2017.
La operacion de este equipo esta sujeta a las siguientes dos condiciones:
Es posible que este equipo o dispositivo no cause interferencia perjudicial y.
Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacion no deseada.
Fabricante: Mikrotikls SIA, Brivibas gatve 214i, Riga, LV-1039, Latvia.
País De Origen: Letonia; Lituania; China (Republica Popular); Estados Unidos De America; Mexico.
Por favor contacte a su distribuidor local para preguntas regionales específicas. La lista de importadores se puede encontrar en nuestra página de inicio –
https://mikrotik.com/buy/latinamerica/mexico.
The National Commission for the State Regulation of Communications and
Informatization by Ukraine
Виробник: Mikrotikls SIA, Brivibas gatve 214i Рига, Латвія, LV1039.
CE Declaration of Conformity
Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039.
Hereby, Mikrotīkls SIA declares that the radio equipment type RBLHGG-60ad is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address:https://mikrotik.com/products
WiGig
Operational channels /Maximum output power
Betriebskanäle /maximale Ausgangsleistung
Canaux opérationnels /puissance de sortie maximale
Canali operativi /massima potenza di uscita
Canales operacionales /potencia de salida máxima
Операционные каналы /максимальная выходная мощность
58.32 GHz / <40 dBm
60.48 GHz /<40 dBm
62.64 GHz /<40 dBm
Справжнім Mikrotikls SIA заявляє, що маршрутизатор відповідає основним вимогам та іншим відповідним положенням директиви 2014
/53/EC, а також суттєвим вимогам Технічного регламенту радіообладнання, затвердженого постановою Кабінету Міністрів України від
24 травня 2017 року № 355.
Для експлуатації в Україні необхідно отримати дозвіл на експлуатацію у порядку, затвердженому рішенням НКРЗІ від 01.11.2012 № 559,
зареєстрованому в Міністерстві юстиції України 03.01.2013 за № 57/22589.
Note. Information contained here is subject to change. Please visit the product page on
www.mikrotik.com for the most up to date version of this
document.
Otros manuales para LHG 60G
5
Tabla de contenidos
Otros manuales de Hardware de red de MikroTik
MikroTik
MikroTik RouterBOARD 800 Series Manual de usuario
MikroTik
MikroTik cAP ax Manual de usuario
MikroTik
MikroTik CCR2004-1G-2XS-PCIe Manual de usuario
MikroTik
MikroTik CCR2004-16G-2S+ Manual de usuario
MikroTik
MikroTik AP Manual de usuario
MikroTik
MikroTik RouterBOARD 711-5HnD Manual de usuario
MikroTik
MikroTik PL7411-2nD Guía de inicio rápido
MikroTik
MikroTik nRAY Series Manual de usuario
MikroTik
MikroTik netFiber 9 Manual de usuario
MikroTik
MikroTik hAP ax lite LTE6 Manual de usuario
MikroTik
MikroTik Wireless Wire Manual de usuario
MikroTik
MikroTik hAP lite Manual de usuario
MikroTik
MikroTik RBM11G Manual de usuario
MikroTik
MikroTik Network Controller Manual de usuario
MikroTik
MikroTik RouterBOARD 750G Manual de usuario
MikroTik
MikroTik RouterBOARD 33/433AH Manual de usuario
MikroTik
MikroTik RouterBOARD SXT G-2HnD Manual de usuario
MikroTik
MikroTik S53UG+M-5HaxD2HaxD-TC&RG502Q-EA Manual de usuario
MikroTik
MikroTik RouterBOARD 450 Series Manual de usuario
MikroTik
MikroTik CCR1009-7G-1C-1S+ Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
