Mikroe BOARDS XBEE click Manual de usuario

2 3

2. Soldering the headers

3. Plugging the board in

Once you have soldered the headers your

board is ready to be placed into the desired

mikroBUS™socket. Make sure to align the

cut in the lower-right part of the board with

the markings on the silkscreen at the

mikroBUS™socket. If all the

pins are aligned correctly,

push the board all the way

into the socket.

Turn the board upward again. Make sure

to align the headers so that they are

perpendicular to the board, then solder the

pins carefully.

Turn the board upside down so that

the bottom side is facing you upwards.

Place shorter pins of the header into the

appropriate soldering pads.

Before using your click board™, make sure

to solder 1x8 male headers to both left and

right side of the board. Two 1x8 male headers

are included with the board in the package.

4. Essential features

XBee click is network-compatible with other

devices that conform to ZigBee standards. The

module operates at the 2.4-2.5GHz band, has

a wireless range of up to 60m indoors, or up to

1.2km outdoors (line-of-sight). The RF data

rate is up to 250 Kbps. To simplify deployment,

the click features a commissioning button

and an associated LED. They allow you to

issue simple conguration commands with

subsequent button presses (joining or leaving

networks, self-identication, restoring default

values etc.)

XBee click carries the Xbee®and Zigbee-

compliant XB24CZ7PIS-004 module with

a PCB antenna from Digi International. The

module provides wireless connectivity to

end-point devices in ZigBee mesh networks.

The board can communicate with the target

MCU either through the mikroBUS™UART

interface (TX, RX, RTS i CTS), or SPI (MISO,

MOSI, SCK, CS). Additional functionality is

provided by, Reset, and ATTN-DTR pins. Uses

3.3V power supply only.

1. Introduction

XBEE click Manual v101

0100000090060

XBEE click

click

BOARDS™

www.mikroe.com

SCK

SDI

SDO

SCK

SDI

SDO

RTS

CTS

ATTN

10K

VCC-3.3VVCC-3.3V

C2 10uF

VCC-3.3V

VCC-3.3VVCC-3.3V

2K2

LD1

C1 100nF

LD2

2K2

PDTC114EU

RTS CTS

VCC-3.3V31

DIO1/AD1

DIO0/AD0/CB

Reserved

GND

Reserved

DIO9/On_nSLEEP

VREF

DIO5/ASSOC

DIO6/nRTS

DIO3/AD3

DIO2/AD2

GND

Reserved

DIO4

DIO7/nCTS

GND

VCC

DOUT/DIO13

DIO14/DIN/nCONFIG

DIO12

nRESET

DIO10/ RSSI PWM/PWM0

DIO11/PWM1

Reserved

DIO8/nDTR/SLEEP_RQ

GND

DIO19/SPI_nATTN

GND

21 Reserved

Reserved

DIO15/SPI_SO

DIO16/SPI_SI

DIO17/SPI_nSSEL

DIO18/SPI_CLK

XBEE

XBee RF Module

100nF

RESET_N

VCC-3.3V

RST

SCK

MOSI

MISO

+3.3V

GND

PWM

INT

SCL

SDA

+5V

GND

MIKROBUS DEVICE CONN.

DTR

ATTN-DTR

VCC-3.3V

ATTN-DTR

ASSOC

8. Code examples

MikroElektronika oers free tech support

(www.mikroe.com/support) until the end of

the product’s lifetime, so if something goes

wrong, we’re ready and willing to help!

Once you have done all the necessary

preparations, it’s time to get your click board™

up and running. We have provided examples

for mikroC™, mikroBasic™and mikroPascal™

compilers on our Libstock website. Just

download them and you are ready to start.

.com

6. Dimensions

MikroElektronika assumes no responsibility

or liability for any errors or inaccuracies

that may appear in the present document.

Specication and information contained in

the present schematic are subject to change

at any time without notice.

mm mils

LENGTH 57.15 2250

WIDTH 25.4 1000

HEIGHT* 5.33 210

5. Schematic

7. ATT/DTR jumper

9. Support

25.4 mm / 1000 mils

57.15 / 2250 mils

* without headers

10. Disclaimer

The ATT/DTR jumper is

for setting the interrupt

feature, depending on

whether SPI or UART is

used for data transmission

(ATT for SPI, DTR for UART).

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Mikroe:

MIKROE-1599

Otros manuales de Microcontrolador de Mikroe

Mikroe

Mikroe click GPS2 Manual de usuario

Mikroe

Mikroe PICPLC16 V7A Manual de usuario

Mikroe

Mikroe click Proximity 2 Manual de usuario

Mikroe

Mikroe SEMITECH N-PLC Click Instrucciones de instalación y funcionamiento

Mikroe

Mikroe Click Board Expand Click Manual de usuario

Mikroe

Mikroe RELAY 2 click Manual de usuario

Manuales populares de Microcontrolador de otras marcas

AMS

AMS AS7261 Demo Kit Manual de usuario

Novatek

Novatek NT6861 Manual de usuario

Espressif Systems

Espressif Systems ESP8266 SDK Guía de configuración

Nuvoton

Nuvoton ISD61S00 ChipCorder Guía

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manual de usuario

Texas Instruments

Texas Instruments Chipcon CC2420DK Manual de usuario

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manual de usuario

NEC

NEC 78GK0S/K 1+ Series Instrucciones de instalación y funcionamiento

Intel

Intel Agilex Manual de usuario

Cypress

Cypress CY4607 HX2VL Manual de usuario

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manual de usuario

Texas Instruments

Texas Instruments TMS320F2837 D Series Manual de usuario

CYPRES

CYPRES CY14NVSRAMKIT-001 Manual de usuario

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manual de usuario

Espressif Systems

Espressif Systems ESP8266EX Instrucciones de funcionamiento

Abov

Abov AC33M8128L Manual de usuario

Laird

Laird BL654PA Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F800 Manual de usuario