MIKAFON DOC16 Manual de usuario

USER MANUAL

DOC16

Main Control Unit

 
 

Table of Contents 
DOC16 MAIN CONTROL UNIT................................................................................................................. 6 
a. Device Characteristics .................................................................................................................... 6 
b. Device Functions & Specifications ................................................................................................. 7 
CONTROLS, CONNECTORS & INDICATORS............................................................................................. 8 
1. Front Panel....................................................................................................................................... 8 
1.1 LCD Touchscreen........................................................................................................................ 9 
Main Menu ................................................................................................................................. 9 
a Amplifier Status................................................................................................................... 10 
i. Monitoring Page................................................................................................................ 10 
ii. Password........................................................................................................................... 12 
iii. Zone Selection ................................................................................................................. 13 
iv. Emergency ....................................................................................................................... 13 
v. Amplifier Errors................................................................................................................. 14 
b Settings ............................................................................................................................... 15 
i. Channels ............................................................................................................................ 15 
ii. Calibrate............................................................................................................................ 16 
iii. Line Control...................................................................................................................... 16 
c Emg...................................................................................................................................... 16 
d System Logs......................................................................................................................... 16 
2. Rear Panel...................................................................................................................................... 17 
COMPUTER SETUP................................................................................................................................ 20 
1. User Interface ................................................................................................................................ 20 
General System Setup .................................................................................................................. 20 
a Device Setup............................................................................................................................ 21 
b File Manager ........................................................................................................................... 22 
c Device Match........................................................................................................................... 24 
Control Input ................................................................................................................................ 25 
a Input Contacts......................................................................................................................... 25 
b Control Input Setup................................................................................................................. 26 
c Control Buttons ....................................................................................................................... 28 
Audio ............................................................................................................................................ 29 
a Zone Names ............................................................................................................................ 29 

 
 

b Speaker Out Setup .................................................................................................................. 30 
c Audio Matrix............................................................................................................................ 30 
Scheduled Tasks ........................................................................................................................... 31 
Other System Setup...................................................................................................................... 33 
a. Amplifier Connection ............................................................................................................. 33 
b. Others ................................................................................................................................... 34 
DSP SETUP ............................................................................................................................................ 35 
1. Introduction & Connection ........................................................................................................... 35 
2. Menus & Instructions.................................................................................................................... 35 
2.1. DOC16 Output Menu .............................................................................................................. 35 
a. Naming...................................................................................................................................... 36 
b. Gain .......................................................................................................................................... 36 
c. Equalizer.................................................................................................................................... 37 
d. Crossover.................................................................................................................................. 37 
e. Limiter....................................................................................................................................... 38 
f. Volume ...................................................................................................................................... 38 
g. Invert ........................................................................................................................................ 39 
h. Channel X.................................................................................................................................. 39 
2.2. Equalizer, Crossover & Limiter ................................................................................................ 39 
2.2.a. Equalizer.......................................................................................................................... 39 
2.2.b. Crossover......................................................................................................................... 40 
2.2.c. Limiter.............................................................................................................................. 41 
2.3. Settings Menu ......................................................................................................................... 42 
INSTALLATION & COMMISSIONING INSTRUCTIONS............................................................................ 43 
TECHNICAL SPECIFICATIONS ................................................................................................................ 45 
CABLE CONNECTION DIAGRAM ........................................................................................................... 46 
BLOCK DIAGRAM.................................................................................................................................. 47 
DECLARATION OF MANUFACTURER .................................................................................................. 47 
COMFORMITY..................................................................................................................................... 47 
WARRANTY......................................................................................................................................... 47 
 
 

IMPORTANT NOTICES

•Before installing and using the device, please read this manual carefully and

keep it for further use.

•This manual is an integral part of the product. It should be given to the new

owner in order for them to know the installation, operation and safety

instructions.

•Improper installation of the device removes the responsibility of the

manufacturer.

WARNING

•To avoid the risk of fire and electric shock, never expose this equipment to

rain or moisture!

SAFETY PRECAUTIONS

1. Please read the instructions carefully, as they contain important information.

2. The voltage of the power supply of this device has high values, which creates a

risk of electric shock. For this reason, never install, connect or disconnect this

product while the power supply is connected.

3. The metal parts of the product are grounded with an electric cable. If the

electrical outlet that supplies electricity is not grounded, call a qualified

electrician who will ground the product through the terminal.

4. To prevent damage to the cable, make sure the power supply cable is not

crushed or broken.

5. To avoid the risk of electric shock, never open the product: there are no user

fixable parts inside.

6. Make sure that foreign bodies or liquids do not come in contact with speakers, as

this may cause short circuit.

7. Never try to perform repairs which are not mentioned in this manual. Contact

the authorized service center or highly qualified personnel if;

a. The product is not operating (or abnormally operating),

b. Serious damage is done to the power supply cord,

c. Foreign bodies or liquids get into the product,

d. The product is exposed to heavy impact.

8. Turn off the product, if not used for a long time and disconnect the power supply

cord.

9. If the product emits a strange odor or smoke, turn off immediately and

disconnect the power supply cord.

PRECAUTIONS

•Do not cover ventilation of the product.

•Do not allow amplifier to operate with an excessive load for a long time.

•Tighten the screws on the speakers firmly to guarantee safe contact.

•Do not use thinner, alcohol or other volatile substances when cleaning

exterior parts.

CAUTIONS RELATED TO THE USE OF ELECTRICAL LINE

•When plugging and unplugging the power cord, it should be held firmly to

avoid risk.

•In case it won’t be used for a long time, the plug of the unit should be

unplugged to cut off the electricity.

•To avoid damaging the power cord, do not break, pull or harm the cord with

sharp and pointy materials. Use a grounded socket.

POSITIONING

•It should be placed with it’s sides and back 1 meter away from the wall and

should not be placed in the following environments;

oHumid environment

oUnder direct sunlight and other strong heat emitters

oEnvironments without ventilation

CONTROL OF THE UNIT

•Make sure that the power supply is turned off, that the power supply and the

other devices and lines connected with this unit are disconnected from the

power supply.

•Do not remove this unit. Do not attempt to disassemble and fix this device

yourself. Otherwise there may be a risk of electric shock or fire. If you can’t

solve the problems with the methods outlined later in this manual, you should

call a qualified technician or consult our company. Enforcing the system could

may electrical shock or fire.

CLEANING

•When this unit needs to be cleaned, use a clean damp cloth etc. to dust. Do

not use solvents such as benzene, thinner alcohol, strong volatile substances,

bleach or other flammable liquids for cleaning the body of the unit.

2. DOC16 MAIN CONTROL UNIT

The EnormPA DOC system fully complies with European Normative EN 54-16 and meet all

requirements for voice alarm control and indicating equipment. DOC16 is the main control unit

of the system with 16 channels.

The DOC16 is an Ethernet based PA/VA system, which supports up to 16 channels. Designed to

operate decentralised, it’s not only fully reliable, it also provides the highest safety functions

such as spare power amplifier switching, failure detection and indication in all emergency tasks,

real time speaker line impedance monitoring and reliable open circuit or short-circuit detection.

Applying cutting edge multi-connectivity, there is no limit in terms of communication and

flexibility. All I/O are fully programmable and allow transmitting automated or delayed

emergency announcements to any selected zones. The DOC16 system can be easily integrated

and thanks to its plug-and-play philosophy; installation, maintenance and operation costs are

reduced significantly.

Please find functions and characteristics below.

2. a. Device Characteristics

1. Allows selection of source files and zone buttons in the process of making an

announcement by using alarm, alert buttons or PTT microphone.

2. Includes a PTT microphone for emergency and public address announcements.

3. Indicates status through LED lights in front panel.

4. Supports remote announcing and broadcasting through MA5/microphone console.

5. Includes 16 defined A-B zones.

6. Includes 1 USB media input, 2 external stereo inputs and 1 music server (for ex. MS40)

input.

7. Supports speaker line supervision and ground fault detection.

8. Protects main and backup power sources each by a fuse. In case of any error in main

power source, it automatically switches to backup and vice versa. This situation is

indicated by a LED in front panel of the device.

9. Accommodates a built-in speaker for zone supervision.

10. The permanent built-in memory is 8GB, 850MB of this memory is used for keeping

source files and 2600MB is used for recording.

11. Max. of 3 source files can be played through network or from internal files.

12. Supports switching between amplifiers.

13. Supports self testing and automatic fault detection.

14. Controls volume automatically regarding the noise in the environment.

15. Zone and source names can be defined. Button function descriptions can be entered

easily.

16. Lets any source file to be broadcasted in any zone by internal sound file selector.

17. Supports broadcasting through scheduled tasks.

18. System is expandable up to 64 zones.

19. Lets any fault description to be seen from the LCD touch screen.

20. Traceable and recordable logs are held within the system.

21. Supports announces and messages to be kept in memory and broadcasted according to

given priority, except emergency situations.

22. Includes DSP module.

23. Benefits RS485 protocol for external communication.

2. b. Device Functions & Specifications

-Main & Backup Power Supply

-Power Source Protection

-Line Fault Detection

-Supervision Function

-Self-check Function

-Automatic Volume Control

-Power Amplifier Management

-Emergency Voice Alarm Function

-Public Address Function

-Broadcast Mp3 File

-Software Configuration

-Software Monitoring

-Simple Settings and Crosscheck from Software

Access levels of the system is complying with EN54-16 requirements. Definitions are in the

following Table 1;

Access Level 1

Monitoring all system functions.

Access Level 2

* Emergency voice alarm and public address announcement,

* Live announcement with microphone,

* Quiescent condition (Reset function),

* Background music zone and volume control and

* Line control by authorized personel.

Access Level 3

Configuring settings and doing maintenance of the system according to

instructions and informations that are presented in this manual.

Access Level 4

Operations like repairing which leads to changing components in

hardware or software by Manufacrurer’s technical service personel.

Table 1 Access Level Authorities

3. CONTROLS, CONNECTORS & INDICATORS

3.1. Front Panel

Figure 1 DOC16 Front Panel

1. Media: USB (mp3) input used for broadcasting music to the system.

2. Disabled LED: Lights up yellow when the respective function (“Disable”) is selected from

the interface. In this case, tests in order to find faults according to EN54-16 will not be

performed, all will be disabled. This function must be used if the installation of the

system is not complying with EN54-16.

3. General Fault LED: Lights up red if any fault is detected within the system. The status of

the error can be seen from the LCD screen. The LED turns off when all components of

the system runs smoothly.

4. Public Announcement LED: Lights up yellow when the device is stable. In case of any

emergency situation this LED will turn off and Emg Status will light up.

5. Emg Status LED: Lights up red when an emergency situation occurs, an announcement is

made from Emg Microphone or when Alarm or Alert message is being broadcasted.

6. Power LED: Lights up green when there’s 220VAC, turns off any otherwise.

7. Alarm Button: Has the 2nd degree in priority ranking. When pressed, system will ask for

a password, then all broadcastable zones come as selected on LCD screen. Undesired

zones can be unselected to remove. Green check sign is pressed in order to start the

broadcast. Likewise red cross sign is pressed in order to stop the broadcast. Emg status

LED will light up during the alarm broadcast. Mp3 file can be changed as desired from

the web interface. (See 4.2.c, pg.28)

8. All Call Button: If there’s any unselected zones from the LCD screen in Alarm and Alert

processes, All Call Button will call all zones back and active them.

9. Alert Button: Has the 3rd degree in priority ranking. When pressed system will ask for a

password, then all broadcastable zones come as selected on LCD screen. Undesired

zones can be unselected to remove. Green check sign is pressed in order to start the

broadcast. Likewise red cross sign is pressed in order to stop the broadcast. Emg status

LED will light up during the alert broadcast. Mp3 file can be changed as desired from the

web interface. (See 4.2.c, pg.28)

10. Reset Button: Used for stopping Alarm or Alert broadcasts.

11. Emg Microphone: Has the 1st degree in priority ranking. It is the input of Emergency

PTT Microphone. Original microphone must be used which is included within the device

packaging. In case of any fault caused from the microphone, the system gives a warning

(MIC.) from the LCD screen. Emg status LED and the LED next to the microphone socket

will light up red when it’s activated.

12. LCD Screen: 5” LCD touchscreen. Detailed information is given in the following.

3.1.1 LCD Touchscreen

From the 5” LCD Touchscreen in front of DOC16, various controls can be made and statuses can

be monitored. When DOC16 is energized the default page on LCD Touchscreen is “Amplifier

Status”.

1. Main Menu

Main menu includes 4 sub-menus. You can find detailed explanations below. Date, time, IP

Address of the device and the version of the software can be seen from this page.

Figure 2 LCD Touchscreen Main Menu

1.a Amplifier Status

i. Monitoring Page

Zones that are connected to amplifiers can be monitored through this page. It is the default page of LCD

Touchscreen. In order to access the main menu, cross sign is pressed and password is entered. Once the

password is entered user can see that she is in Access Level 2 from top right. Cross sign is pressed again

to access the “Main Menu”.

Figure 3 LCD Touchscreen / Main Page

1. CH 1…16: Indicator columns of 16 zones.

2. Emg: Emergency situation indicator row. A red exclamation point sign will be seen when

there’s an emergency status broadcast is going on in respective zone (channel) column.

3. Flt/Dis: Error status indicator in that respective zone (channel). Error sign is shown with

yellow exclamation point.

4. Signal: Indicates existence of sound signal in that respective zone (channel). It is shown

with green check sign.

5. Line A/B: Indicator of speaker line status. Any fault in the line will be shown with yellow

exclamation point. If the lines are running smoothly green check sign will be seen.

6. CIE: Monitors the status of Contact In inputs at the rear panel. If there’s no problem on

the cables that are connected to these contacts, a green check sign will be seen,

otherwise in case of any error due to cables, a yellow exclamation point will be seen on

the screen.

7. PROTECT: Monitors the status of amplifiers connected to the system. If there’s no

problem due to amplifiers, a green check sign will be seen, otherwise in case of any

error, a yellow exclamation point will be seen on the screen.

Tabla de contenidos

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario