Migatronic AUTOMIG 2 Manual de usuario

QUICKGUIDE AUTOMIG2

50113773 E

AUTOMIG II - Factory setting

Setting possibilities Area Step Factory setting Unit

Primary parameters:

1 Welding current Area depends on

program

1 Depending on

program

Wire feed speed 0.1 m/min

Thickness of material 0.1 mm

2 Arc length -9.9 - +9.9 0.1 0.0 V

Secondary parameters:

1 Inductance -5.0 - +5.0 0.1 0.0 -

2 Gas pre ﬂow 0.0 - 10.0 0.1 0.2 s

3 Soft start Off / 1.5 - 18.0 0.1 1.5 m/min

4 Hotstart time 0.0 - 10.0 0.1 0.5 s

5 Slope down 0.0 - 10.0 0.1 0.2 s

6 Burnback 1 - 30 1 5 ms

7 Gas post ﬂow 0.0 - 10.0 0.1 3 s

9 Stop amp 0 - 100 1 50 %

r Remote control 0 = internal

1 = torch control

Programs

No. Wire Material Gas

P106 Ø 0.6 mm Fe SG2 ER70S6 CO2

P101 Ø 0.8 mm Fe SG2 ER70S6 CO2

P109 Ø 0.9 mm Fe SG2 ER70S6 CO2

P102 Ø 1.0 mm Fe SG2 ER70S6 CO2

P116 Ø 0.6 mm Fe SG2 ER70S6 ArCO2(82/18)

P111 Ø 0.8 mm Fe SG2 ER70S6 ArCO2(82/18)

P119 Ø 0.9 mm Fe SG2 ER70S6 ArCO2(82/18)

P112 Ø 1.0 mm Fe SG2 ER70S6 ArCO2(82/18)

P311 Ø 0.8 mm AlMg5 ER5356 Ar

P319 Ø 0.9 mm AlMg5 ER5356 Ar

P312 Ø 1.0 mm AlMg ER5356/ER5554 Ar (100)

P359 Ø 0.9 mm AlSi5 ER4043 Ar (100)

P352 Ø 1.0 mm AlSi5 ER4043 Ar

P369 Ø 0.9 mm AlMg3Mn ER5554 Ar (100)

P372 Ø 1.0 mm AlSi12 ER4047 Ar (100)

P501 Ø 0.8 mm CuAl8 Brazing ArCO2(98/2)

P509 Ø 0.9 mm CuAl8 Brazing ArCO2(98/2)

P502 Ø 1.0 mm CuAl8 Brazing ArCO2(98/2)

P561 Ø 0.8 mm CuSi3 Brazing ArCO2(98/2)

P569 Ø 0.9 mm CuSi3 Brazing Ar (100)

P562 Ø 1.0 mm CuSi3 Brazing ArCO2(98/2)

QUICKGUIDE AUTOMIG2

2 Selecting wire diameter

Press the key until the LED is lit at the

relevant wire diameter.

Selection of AlMg/AlSi programs:

1. Select material the material type

“Al”

2. Select material type 0.9 or 1.0mm

3. Keep the material key pressed for

5sec until the “Al” LED is switched

off as indication of entrance to set-

up mode.

The display shows

319 (0.9 mm AlMg ER5356),

359 (0.9 mm AlSi5 ER4043) or

369 (0.9 mm AlMg3Mn ER5554)

if 0.9 mm wire has been selected, or

312 (1.0 mm AlMg ER5356/ER5554),

352 (1.0 mm AlSi5 ER4043) or

372 (1.0 mm AlSi12 ER4047)

if 1.0mm wire has been selected.

4. Turn the control knob back and forth

until the correct program is dis-

played.

5. The program is selected by one more

press on the material key knob, and

the machine will return to normal

mode.

Reset function

Press and hold the key for 5 seconds.

Flashing LED indicates that the relevant

program is reset to factory settings.

AUTOMIG II CONTROL PANEL

I. Switch on the machine

II. Select type of material and

wire diameter

III. Set one of the following parameters:

welding current, wire feed speed or

thickness of material

IV. Trim the arc length, if required

1 Selecting type of material

Press the key until the LED is lit at the

relevant material.

5 Control knob

Adjustment of welding current, wire

feed speed, thickness of material or

arc length. Inching speed is adjustable

during wire inching. If the key for

secondary parameters is active, it

is possible to trim the secondary

parameters.

6 Secondary parameters

Press the key until the desired

parameter is shown on the display.

Press key 3brieﬂy to ﬁnish.

AWelding voltage

B Warning – overheating

m/min

Arc adjust (electronic choke)

Remote control

Set welding current (A)

Hotstart (t)

Soft start

(m/min.)

Gas pre ﬂow (t)

Burnback

Gas post ﬂow (t)

Slope down (t)

Stop amp (%)

3 Primary parameters

Set one of the following primary

parameters at your own option and

according to relevance: welding current,

wire feed speed or thickness of material;

the parameters are closely connected in

the machine.

4 Arc length

The arc length can be adjusted as

required. Press the key under the symbol

and turn the control knob until the

desired arc length is achieved (-9.9 to

+9.9).

Otros manuales de Sistema de soldadura de Migatronic

Migatronic

Migatronic FOCUS TIG 160 DC HP PFC Manual de usuario

Migatronic

Migatronic RALLY MIG 161i Manual de usuario

Migatronic

Migatronic RALLY MIG 161i Manual de usuario

Migatronic

Migatronic MIG 385 MK III Manual de usuario

Migatronic

Migatronic MTE DIALOG Manual de usuario

Migatronic

Migatronic PI 250 MMA Manual de usuario

Migatronic

Migatronic RALLY MIG 161i Manual de usuario

Migatronic

Migatronic OMEGA 220 Manual de usuario

Migatronic

Migatronic AUTOMIG Manual de usuario

Migatronic

Migatronic OMEGA 220 Manual de usuario

Migatronic

Migatronic CMI 183i Manual de usuario

Migatronic

Migatronic PILOT 1800 Manual de usuario

Migatronic

Migatronic FOCUS STICK 160E PFC Manual de usuario

Migatronic

Migatronic DELTA 180 E PFC Manual de usuario

Migatronic

Migatronic PI 350 AC/DC Manual de usuario

Migatronic

Migatronic SIGMA NEXT RC 400 Manual de usuario

Migatronic

Migatronic MCU 1000 Manual de usuario

Migatronic

Migatronic OMEGA2 CoWelder 300 Manual de usuario

Migatronic

Migatronic SCOUT 130 E Manual de usuario

Migatronic

Migatronic MIGACUT 5i Manual de usuario

Migatronic

Migatronic LTE 200 Manual de usuario

Migatronic

Migatronic AUTOMIG2 183i Manual de usuario

Migatronic

Migatronic PI 320 DC Manual de usuario

Migatronic

Migatronic Multimotive 220 Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario