Miele K 2601 Vi Manual de usuario
11618780-01
Installation
*INSTALLATION*
Location
This appliance should be installed in a
dry, well-ventilated room.
When deciding where to install your
refrigerator, please bear in mind that it
will use more energy if installed near a
heater, cooktop or other appliance that
gives off heat. Direct sunlight should
also be avoided.
The higher the room temperature, the
longer the compressor will run and the
higher the energy consumption will be.
Please note the following when
installing the appliance:
- The mains socket must not be
located directly behind the appliance
and must be easily accessible.
- The plug and the power cable must
not touch the rear of the refrigeration
appliance as they could be damaged
by vibrations from the appliance.
- Nor should other appliances be
plugged into a socket located directly
behind this appliance.
If installation near a heat source is
unavoidable, observe the following
minimum distances between the
appliance and the heat source:
- at least 3cm
to electric or gas stoves
- at least 30cm
to oil or coal stoves.
If it is not possible to observe these
minimum distances, an insulation plate
must be installed between the
refrigeration appliance and the heat
source.
Climate range
The appliance is designed for use within
a certain climate range (ambient
temperatures) and should not be used
outside this range. The climate range of
the appliance is stated on the data plate
inside the appliance.
Climate range Ambient room
temperature
SN +10 to +32°C
N +16 to +32°C
ST +16 to +38°C
T +16 to +43°C
Operating in a room which is too cold
will result in the compressor switching
off for too long, causing the internal
temperature in the appliance to rise with
the risk of food deteriorating and going
off.
11618780-01
Installation
*INSTALLATION*
Risk of damage due to high
humidity.
In environments with high humidity,
condensation can build up on
external appliance panels, which can
cause corrosion.
Install the refrigeration appliance in a
dry and/or air-conditioned room with
sufficient ventilation.
After installation, make sure that the
appliance door(s) close properly, the
ventilation gaps are not covered and
that the refrigeration appliance has
been installed in accordance with
these operating and installation
instructions.
Installation notes
Danger of damage and injury
due to the appliance tipping over!
This refrigeration appliance is very
heavy and can tip forwards when the
door(s) is/are open.
Keep the appliance door(s) shut until
the appliance has been built in and
secured in its housing in accordance
with these operating and installation
instructions.
Due to the size and weight of the
appliance, installation must be
carried out by two people.
Adjoining cabinets/units
The appliance is screwed to the
adjoining cabinets/units to the side and
above. For this reason, it is essential
that all cabinets/units are fixed to the
ground or wall.
11618780-01
Installation
*INSTALLATION*
Load-bearing capacity of the niche
floor
To ensure the safe installation of the
appliance and to guarantee its correct
functioning, the floor of the niche where
the appliance is to be installed must be
smooth and even.
It must be made from strong, rigid
material.
Because the appliance is extremely
heavy when fully loaded, it is essential
that the floor it stands on is able to bear
its weight. If necessary, seek the advice
of an architect or construction expert.
When fully loaded, the approx. weight
of the appliance is:
K 2601 Vi 325 kg
Ventilation
Risk of fire and damage due to
insufficient ventilation.
If the refrigeration appliance is not
ventilated sufficiently, the
compressor will run more frequently
and for longer periods.
This will result in increased energy
consumption and a higher operating
temperature of the compressor. This,
in turn, can result in damage to the
compressor.
Please ensure that there is adequate
ventilation around the appliance.
It is essential to observe the required
ventilation gaps. The ventilation gaps
must not be covered or blocked in
any way.
Door hinging
Risk of damage and injury when
changing the door hinge.
Changing the door hinge single-
handedly can cause damage to the
appliance and injury.
The appliance is supplied with fixed
hinges. Under no circumstances
should you attempt to change the
door hinging yourself.
If you need to change the door
hinges to the other side, please
contact Miele customer service.
11618780-01
Installation
*INSTALLATION*
Side-by-side units
This appliance can be installed side by
side with another refrigeration
appliance. The following overview will
show you which side-by-side
installation options you have with your
refrigeration appliance.
Depending on the installation
situation, you may need the side-by-
side installation kit (see “Accessories -
Optional accessories”).
Instructions for installing appliances
side by side can be found in the side-
by-side installation kit installation
instructions.
. . . with partition wall
The wall a between the side-by-side
refrigeration appliances must be at
least 16mm thick.
If the door hinges of the appliances
are next to each other, you must take
into account the thickness of the
cabinet fronts and door handles so
that the appliance doors do not
collide and become damaged if they
are opened at the same time.
The appliances are secured individually
in their niche using the supplied
installation material.
If the partition wall a is between 16 mm
and 160mm, you will need the side
panel heater from the side-by-side
installation kit to prevent condensation
from forming and any resulting damage.
When planning installation niches,
please note that the niche into which
the refrigeration appliance with the
side panel heater is installed must be
4mm wider (see “Installation –
Installation dimensions”).
If the partition wall a is thicker than
160mm, you do not need the side-by-
side installation kit, nor the side panel
heater.
11618780-01
Installation
*INSTALLATION*
. . .without partition wall
If the appliances are to be installed next
to each other without a partition wall
between them, they will need to be
joined together with the side-by-side
installation kit. In addition, you must
install the side panel heater to prevent
condensation from forming and any
resulting damage.
11618780-01
Installation
*INSTALLATION*
Installation dimensions
A
B
C
A B C
K 2601 Vi 2134–2164 mm 610 mm 610 mm + furniture front
(19–38mm)
11618780-01
Installation
*INSTALLATION*
30 mm
22 mm
≥ 262 mm
102 mm ≥ 102 mm
≥ 85 mm
Side view
11618780-01
Installation
*INSTALLATION*
Dimensions when the appliance door is open (opening angle90°/115°)
10 mm
D
A
B
C
A B* C* D (with a furniture
front of 19mm)
K 2601 Vi 677 mm Furniture
front
(19–38mm)
Handle 296 mm
* The dimensions of the furniture front and the door handle vary depending on the
design of the kitchen.
11618780-01
Installation
*INSTALLATION*
Dimensions of the furniture front
A
B
C
A B C
K 2601 Vi 604 mm 2029 mm ≥ 102–132 mm
11618780-01
Installation
*INSTALLATION*
Installing the appliance
Before you start
It is essential to read these operating
and installation instructions carefully
before starting to install the
appliance.
The refrigeration appliance should be
installed by a suitably qualified and
competent installer in accordance
with these operating and installation
instructions. Safe operation of the
appliance is only assured if it has
been installed and connected in
accordance with these operating and
installation instructions.
Danger of damage and injury
due to the appliance tipping over!
This appliance is very heavy and can
tip forwards when the door is open.
Keep the appliance door shut until
the appliance has been built in and
secured in its niche in accordance
with these operating and installation
instructions.
Due to the size and weight of the
appliance, installation must be
carried out by two people.
Tools required
- Cordless drill
- TX20 screwdriver
- Hammer drill
- Drill bits in various sizes, depending
on materials
- Hammer
- Open-end spanner
- Ratchet wrench, attachment: 8 mm
socket
- Adhesive tape
- Utility knife
- Pipe wrench
- Spirit level
- Tape measure
- Pencil
- Try square
Other
- Step ladder
- Hand trolley
Otros manuales para K 2601 Vi
4
Tabla de contenidos
Otros manuales de Refrigerador de Miele
Miele
Miele K 1911 SF Guía del usuario
Miele
Miele KF 1911 Vi Hoja de especificaciones
Miele
Miele KF 1803 SF Manual de usuario
Miele
Miele KF 1803 Vi Manual de usuario
Miele
Miele KFN 14943 SD ed/cs Manual de usuario
Miele
Miele K 14827 SD Manual de usuario
Miele
Miele KFN 14943 SDE ED Manual de usuario
Miele
Miele KFN 8993 SDE ed Hoja de especificaciones
Miele
Miele K 9552 iD Hoja de especificaciones
Miele
Miele K 9454 iF Hoja de especificaciones
Miele
Miele KFN 14827 SDE ed Hoja de especificaciones
Miele
Miele K 3402 S ed Hoja de especificaciones
Miele
Miele KFN 29233 D bb Manual de usuario
Miele
Miele KFNS 37692 iDE-1 Manual de usuario
Miele
Miele F1473 SF Manual de usuario
Miele
Miele KFN 8997 SE ed Hoja de especificaciones
Miele
Miele K 2601 Vi Manual de usuario
Miele
Miele KS 28423 D ed/cs Manual de usuario
Miele
Miele K 34472 iD Manual de usuario
Miele
Miele KD 3528 Sed Hoja de especificaciones
