Midland A-207 Instrucciones de instalación

A-207 Re-Assembly Instruction Supplement, Ver. 0.0

Issue Date: April 27, 2020

Page 1 of 4

A-207 Re-Assembly Instruction Supplement

1Preparation

These instructions are specific to the reassembly of the A-207 Vacuum Relief Valves. For

more maintenance and installation instructions, please refer to Midland’s Installation,

Operation and Maintenance Instructions for A-205/A-222 Vacuum Relief Valves.

•Exercise normal safety precautions for the commodity involved.

•Discard all soft parts being replaced.

2Valve Details

ITEM

NO.

QTY.

PART NAME

MATERIAL

PART NO.

VACUUM

SETTING

(PSI)

SPRING

PART

NUMBER

BODY

STAINLESS STEEL (PASSIVATED)

207-11-SS-PA

0.75

207-2-MO

SPRING

STAINLESS STEEL

SEE TABLE

207-21-MO

SPRING SEAT

STAINLESS STEEL

207-3-SS

LOCK NUT

STAINLESS STEEL

207-41-SS

STEM

STAINLESS STEEL (PASSIVATED)

207-52-MO-PA

PRESSURE SEAL

WHITE NEOPRENE *

205-6-WNE

SCREEN

ASSEMBLY

STAINLESS STEEL

207-7-SS

RETAINER RING

STAINLESS STEEL

207-8-SS

NAMEPLATE

STAINLESS STEEL

207-90-SS

DRIVE SCREW

STAINLESS STEEL

763-11-SS

* Alternate materials available

A-207 Re-Assembly Instruction Supplement, Ver. 0.0

Issue Date: April 27, 2020

Page 2 of 4

3Re-Assembly Procedure

Put approved lubricant in

the quad-ring grooves on

the stem (item 5).

If the side of the quad-ring

(item 6) with a blue dot can

be identified, put that side

down away from the stem.

Figures 1-2

Slip the quad-ring (item 6)

over the stem (item 5) and

into the quad-ring groove,

making sure the quad-ring

is flat in the groove.

Figures 3-4

Run a steel rule around the groove of the quad-ring to

make sure the back side of the quad-ring is well seated

Run a steel rule under the lower side of the quad-ring

to make sure the back side of the quad-ring is well

seated.

Figure 5

A-207 Re-Assembly Instruction Supplement, Ver. 0.0

Issue Date: April 27, 2020

Page 3 of 4

Put the stem (item 5) in

place.

Put the body (item 1) in

place.

Figures 6-7

Place spring (item 2) and

follower (item 3) on the

stem (item 5) so they end

up about level with the top

of the stem to get the

desired pressure setting.

Put the follower (item 3) in

first, then press it down

slightly. Drive the nut (item

4) down by hand as far as it

can go. Figures 8-9

For A-207 valves without a

hole in the screen, install

the screen (item 7) on top of

valve as shown.

Insert retainer ring (item 8)

in groove as shown.

Figures 10-11

Tabla de contenidos

Otros manuales de Unidad de control de Midland

Midland

Midland A-718C Series Manual de instrucciones

Midland

Midland A-7200 Manual de instrucciones

Midland

Midland A-1075 Manual de instrucciones

Midland

Midland A-520 Series Manual de instrucciones

Midland

Midland A-1477 Series Manual de instrucciones

Midland

Midland A-1076 Series Manual de instrucciones

Midland

Midland A-22075 Series Manual de usuario

Midland

Midland SD-250 Manual de usuario

Midland

Midland A-14150 Series Manual del propietario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario