Midea A24MABOF50 Manual
--
Overseas Thin Range Hood
Installation and Service Manual
Warning
The installation service manual is not intended for ordinary user. Product
maintenance should be done by qualified professional technician. Incorrect
maintenance may cause other danger.
Please cut off the power supply before the maintenance.
If the power cord has hidden fault, please replace it with relevant technical
parameter. (Please refer to the manual for parameter)
Please read the safety warning in the manual carefully before servicing the product.
After the maintenance, detect it according to relevant regulations before using
This service manual includes multiple models. Please refer to the real product
during operation.
Customer Service Center
March.29th, 2014
--
Catalogue
1. Precaution …………………………………………………………1
2. Dimension……………………………………………………………………1
3. Function………… …………………………………………………………2
3.1 Lighting Function…………………………………………………………………..2
3.2 Smoke Absorption Function………………………………………………………2
4. Circuit Diagram………………………………………………………………..3
5. Installation ………………………………………………………………………….3
5.1 Preparation before Installation…………………………………………………..3
5.2 Range Hood Installation…………………………………………………………3
6. Components Dismantling………………………………………………..4
6.1 Filter Mounting and Dismounting………………………………………4
6.2 Check Valve and Fan Cover Dismantling ………………………5
6.3 Spotlight Dismantling…………………………………………………….5
6.4 Dismantle Control Box Assembly ………………………………...5
6.5 Volute Assembly Dismantling……………………………………………….6
6.6 Motor Dismantling ………………………………………………………………..7
6.7 Dismantle Power Cord………………………………………………………….9
6.8 Lamp Holder Dismantling ……………………………………………………….10
7. Troubleshooting…………………………………………………..11
7.1 Electrical Appliance Faults…………………………………………………11
7.2 Main Components Maintenance and Detection…………………….11
-- 1
1. Precaution
1.1 Safety Precaution
1、Please follow the following instructions to avoid hurting the user or other property damage.
2、Faulty operation due to neglecting the instructions will caused injury or damage.
3、Please read the following instructions carefully before the maintenance.
1.2 Warning
1. When replacing the power cord, please use the insulation power cord with model number no less than
3*0.75mm^2 and heat resistance over 70℃.
2. All appliances within 50mm around the product should be heat resistant over 75°C,otherwise, the
surrounding appliances will be deformed in the process of using the product.
3. When remove the packaging material, metal piece, bubble bag, foam and screw, etc should be kept
beyond the reach of children to avoid potential threat, for example, children might swallow smaller
component or suffer suffocation in the process of playing packaging bag.
2. Dimension
-- 2
Note: Dimension data is only for reference.
3. Function
3.1 Lighting Function
As shown in the picture, press or toggle the button indicated by the red circle, the lamp is on; press or toggle
again, lamp is off;
3.2 Smoke Absorption Function
3.2.1 Mechanical Switch
MODEL
X
Y
Z
A24MABOF50
597mm
500mm
140mm
A30MABOF50
757mm
500mm
140mm
A35MABOF50
897mm
500mm
140mm
E60MEBOF52
597mm
500mm
150mm
E76MEBOF52
757mm
500mm
150mm
E90MEBOF52
897mm
500mm
150mm
E60MEBOF96
597mm
500mm
135mm
E76MEBOF96
757mm
500mm
135mm
E90MEBOF96
897mm
500mm
135mm
-- 3
As shown in the picture, press the button indicated by the red arrow, smoke exhaust function of large airflow
is on; press the button indicated by the yellow arrow, switched to smoke exhaust function of middle airflow;
press the button indicated by the green arrow, switched to smoke exhaust function of small airflow; press the
button indicated by the brown arrow, all smoke exhaust functions except lamp are cancelled. All smoke
exhaust function buttons will be auto reset.
3.2.2 Toggle Switch
As shown in the picture, the button indicated by the red circle is toggle switch smoke exhaust control
button, 0,1,2,3 respectively indicate stop, low speed, middle speed and high speed; toggle the switch to the
left and right, the airflow and switch of range hood can be switched freely.
Note: please refer to the User Manual for the specific operation steps of hood function
4. Circuit Diagram
Note: the above is the circuit diagram of basic models, please be subject to the circuit diagram in
product instruction book if there is difference.
5. Installation
5.1 Preparation before Installation
1. Please remove the package first, then install according to the dimension in the following instruction;
(Please dispose the packaging material properly)
2. No inflammable, explosive or non-heat-resistant article should contact or approach around the range
hood.
3. The wall where the hood is hung should have sufficient strength and flatness to ensure that the product
has adequate stability.
-- 4
5.2 Range Hood Installation
Methods 1: as shown in Figure（1）, to ensure the thin range hood in the cabinet, wooden plank should be
parallel to the four lock holes of thin hood top. Install the four screws in the cabinet according to
the relative position of four lock holes and tighten them.
Methods 2: as shown in Figure（2）, first ascertain the relative position on the wall according to the four lock
holes at the back of thin range hood, then punch hole on the top two positions of the wall and
install expansion screw, mount screw within the expansion screw, set aside 3-5mm distance at
screw end, align the two hanging holes at the hood back with the screw, then hang on the wall,
tighten the screw and install the screws at below two holes.
6. Components Mounting and Dismounting
6.1 Filter Mounting and Dismounting
-- 5
Clasp the filter buckle by hand, press down and pull out
6.2 Check Valve and Fan Cover Mounting and Dismounting
Step: as shown in the picture, hold the check valve or fan cover respectively, rotate until the blade
rotated to the vacant position from the board, then, the check valve or fan cover can be taken
down.
6.3 Dismantle Spotlight
Tool: Cross screwdriver
Step: first remove the transparent lamp panel in the front, then hold the incandescent lamp and rotate
inward, take out the bulb, as shown in the following picture.
-- 6
6.4 Dismantle Control Box Assembly
Tool: Cross screwdriver
Step 1: twist off the two fixing screws of control box assembly with cross screwdriver, as shown in the
picture
Step 2: pull out the terminal connecting control box assembly to fan, the control box assembly
dismantling is done, as shown in the picture.
Rotate the bulb in the arrow direction,
take out the bulb
Remove the screw of lamp panel, tilt the
right and push out the lamp panel in the
arrow direction
-- 7
6.5 Volute Assembly Dismantling
Tool: Cross screwdriver
Step: as the above step, pull out the terminal connecting control box assembly to terminal box, twist off
six volute fixing screws on the body top and one grounding screw, take out volute assembly, as
shown in the picture.
6.6 Motor Dismantling
Tool: Cross screwdriver, M4 hex nut sleeve and M5 hex nut sleeve.
Grounding screw of power cord
Volute assembly dismantling is completed.
Grounding screw
Pull out the terminal
Control box assembly
dismantling is completed.
-- 8
Step: as the above step, pull out the terminal connecting the motor to control box assembly, twist off the
four fixing screws of air inlet cover with cross screwdriver, then take out motor impeller assembly,
as shown in the picture.
Black decoration cover and
motor fixing nut
Motor, impeller and air inlet cover
dismantling are completed.
Motor shaft nut and impeller blade
Este manual sirve para los siguientes modelos
8
Tabla de contenidos
Otros manuales de Campana de ventilación de Midea
Midea
Midea MHT60BL Manual de usuario
Midea
Midea MH90A3200W-ES Manual de usuario
Midea
Midea 330173 Manual de usuario
Midea
Midea MHC90GSS Manual de usuario
Midea
Midea MCH-90B68AT Manual de usuario
Midea
Midea MCH-90B65 Manual de usuario
Midea
Midea MCH-90B82 Manual de usuario
Midea
Midea MHB90S Manual de usuario
Midea
Midea WHK 7.62 BL Manual de usuario
Midea
Midea MCHC70J72 Manual de usuario
Midea
Midea MCHC90B68 Manual de usuario
Midea
Midea MH60B3250X-ES Manual de usuario
Midea
Midea 52T01 Manual de usuario
Midea
Midea MHC90CGSS Manual de usuario
Midea
Midea CMPTRAL-SG60 Manual de usuario
Midea
Midea 330152 Manual de usuario
Midea
Midea E60MEW0A09 Manual
Midea
Midea E60MEW2A09 Manual de usuario
Midea
Midea MCH-90J52 Manual de usuario
Midea
Midea MHT90SS Manual de usuario
