Midea VCP6P Manual de usuario
This manual is for reference only, the information has
been carefully checked, if there are any discrepancy, the
factory specifications shall prevail
Quick Start Guide
Cordless Cyclone Vacuum Cleaner
VCP6P
Main unit
Extension tube
Flat nozzle
Electric bed brush
When cleaning high places, accessories can be installed on the extension tube.
Manual
2-in-1 brush Storage buckle
assembly
Storage base
assembly
Power adapter
Electric floor brush
Product Introduction
Installation and component introduction
Parts List
Tips
1. Before placing the machine on the storage rack or when the storage rack is left alone,
be sure to place it on a horizontal surface to avoid falling and damaging the machine;
2. Whether the machine is at work or placed on a storage rack, it must be handled
gently to avoid damage;
1. Installation of storage rack:
Install the storage buckle assembly and storage base as shown in the figure, and
place the assembled storage rack assembly vertically on the horizontal surface as
shown on the right;
Functional Operation
Installation and use of storage rack
Note
2. Placement of the machine:
Before placing the machine on the storage rack assembly, please confirm whether
the placement position is horizontal, and make sure that the machine is turned off
and stopped working. Place the machine on the position of the storage rack gently as
shown in the figure below and leave after the machine is stable.
Functional Operation
Installation and use of storage rack
1. The battery is not charged when shipped from the factory. Please be sure to fully
charge it before use;
2. Do not charge in the environment below 5°C or above 40°C;
3. If the battery power is insufficient during operation, the battery power indicator will flash;
4. When the battery life of the machine becomes significantly shorter and the charging
time becomes longer, please ask qualified personnel to replace the battery. Do not
disassemble the machine yourself in order to avoid danger;
Place the main unit on the storage base smoothly;
Charging time: 4-6 hours
Discharge time: Up to 10 minutes for high power, about 20 minutes for medium
power, and about 1 hour for low power.
Connect one end of the power cord to the socket, and the other end to the
charging port at the end of the battery pack of the main unit. The power
indicator flashes. After the battery is fully charged for a period of time, the
indicator turns off;
Functional Operation
Battery charging
Note
No. Instructions
Indicator light Switch
button
Speed button
LED1
(battery
indicator)
LED3
(speed control
indicator)
LED2
(battery indicator)
Speed button
Switch button
Press the “Switch” button once to start cleaning;
Press the “Switch” button again to stop cleaning;
Battery indication when working (discharging): When LED1 and LED2 are
on, the battery power is sufficient. When LED1 flashes or LED2 turns off,
the battery power is low and needs charging.
When LED1, LED2 and LED3 are all flashing, it indicates an alarm; please
ask qualified personnel to repair;
The default mode is medium power (LED1, LED2 and LED3 are all on)
when power is full; when the “Speed” button is pressed once, it enters high
power (LED1 and LED2 on, LED3 blue); when the “Speed” button is
pressed again, it enters low power (LED1 and LED2 on, LED3 off);
Battery indication when charging: When LED1 or LED2 flashes, the battery power
is low, and the battery needs charging. When both LED1 and LED2 are on, the
battery power is full, and the indicators will turn off after a period of time.
1. To avoid blocking the air duct, please clean up large pieces of garbage in the area
first (such as large pieces of paper, packaging film, etc.);
2. Do not use and store the battery in an environment below 5°C or above 40°C;
3. When disposing of this product, please remove the battery from the machine;
4. It is strictly prohibited to modify the machine, accessories and adapter.
Functional Operation
Clean up
Note
No. Instructions
Take out
Press
Press
Press
To maintain the suction power of the vacuum cleaner, please clean the dust regularly.
Dust cup disassembly
Place the machine flat as shown, press the main lock button with one hand and take out
the dust cup assembly with the other hand.
Dust cup cleaning
Method 1:
Keep the machine body vertical, press the
button, open the lower cover of the dust
cup and pour the dust;
Method 2:
Remove the dust cup as shown in the
figure above, and then press the bottom
cover of the dust cup to pour the dust.
Cleaning and Maintenance
Dust cup disassembly and cleaning
Note
1. The parts in the dust cup are washable;
2. Please make sure that all parts are dry before cleaning and installing them back.
1. Hold the ribs on both sides with your
hands, and gently remove the filter
assembly from the dust cup assembly;
3. After removing the filter assembly, rotate and remove the cyclone as shown in the
figure to clean it. After fully drying, install it back according to the disassembly steps.
Filter
assembly
Uninstall Install back
Filter sponge
Cyclone
assembly
2. Take out the filter sponge and cyclone
components in turn;
Cleaning and Maintenance
Filter disassembly and cleaning
Note
1. Press the button to remove the electric floor brush;
2. Unscrew the roller brush gland according to the instructions, lift the roller brush gland
upward, remove the roller brush for cleaning, and follow the disassembly steps to
install it back after cleaning.
Press
Remove the roller brush gland Remove the roller brush
Cleaning and Maintenance
Disassembly and cleaning of electric floor brush
1. In order to avoid affecting the operation of the electric floor brush, please clean and
maintain it when the roller brush or wheels are tangled or dirty.
2. Before disassembling and maintaining, be sure to stop the operation of the electric
floor brush;
3. It is not recommended to wash the floor brush. The tangled hair can be cleaned with
scissors or a blade, and the dust stuck to the roller brush can be cleaned with a brush.
Note
1. Press the button to remove the
electric bed brush;
3. Wrap disposable chopsticks with paper towels or cloth strips and wipe the inside. If
the roller brush is tangled by hair, use scissors to cut along the roller brush, and then
clean it. After cleaning, follow the disassembly steps above to install it back.
2. Pull out the buckle as shown in the figure
below, and then rotate to remove the
bottom plate;
Pull down
Cleaning and Maintenance
Electric bed brush cleaning
1. When the dust blocks the air duct of the electric bed brush, please use disposable
chopsticks to remove it;
2. Except for the bottom cover, the brush can’t be washed with water;
3. During operation, do not touch the roller brush that rotates at the bottom;
4. To avoid affecting the operation of the electric bed brush, please perform cleaning
and maintenance when the roller brush is tangled or dirty.
Note
Tabla de contenidos
Otros manuales de Aspiradora de Midea
Midea
Midea VCL10 Manual de usuario
Midea
Midea VCS7P Manual de usuario
Midea
Midea P3-L Guía del administrador
Midea
Midea M7 Manual de usuario
Midea
Midea M7 Manual de usuario
Midea
Midea VC-02A14S Manual de usuario
Midea
Midea M7 Manual de usuario
Midea
Midea Eureka I5C Manual de usuario
Midea
Midea C5 PRO Guía del administrador
Midea
Midea VCB42A3670G Manual de usuario
Midea
Midea VCS861P Manual de usuario
Midea
Midea KH19P Manual de usuario
Midea
Midea B8 Series Manual de usuario
Midea
Midea MVC-12M-GR Manual de usuario
Midea
Midea MSB 5.700bs Guía del administrador
Midea
Midea V19P13A20Q0C Manual de usuario
Midea
Midea VCWX10 Manual de usuario
Midea
Midea P12 FLEX Manual de usuario
Midea
Midea C600 Guía del administrador
Midea
Midea M7 Manual de usuario
