Microtek ScanMaker 8700 Manual de usuario

Page 1

Quick Ceph®Systems

Doc ID# 1033ScanMaker8700_Setup - Revision 4/ 3/0

Microtek ScanMaker 8700 Setup

http://www.quickceph.com/docs/1033ScanMaker8700_Setup.pdf

Installing Scanner Software

To allow x-rays to be scanned, remove the default sliding tray from the scanner and replace it with the Glass Film

Holder, as shown on the illustration above. Then, connect the scanner to either the FireWire port on the computer or

the USB hub. Both ports are supported, although using the FireWire port frees up a USB port on the hub.

Now that you have connected the scan-

ner to the computer, it is time to install

the scanner software. Insert the

“Amethyst CD v.1.3” CD-ROM found in

the scanner package.

An icon will appear on

your desktop. Double

click on this icon.

The folder shown to the right will open.

Double click on the icon labeled

“ScanWizard 5 V5.71”, which is highlight-

ed in the image. The program will start

installing onto your computer. You will

need to click on the Restart button after

the installation is finished.

Turn the scanner on its side to reveal the locking screw. To unlock the scanner, use a coin or screwdriver and turn the

locking screw counterclockwise. The screw will push out slightly when unlocked. The scanner should only be locked

for storage or transport.

3When the computer reboots, there will be two new icons on your desktop,

“ScanWizard 5 V5.71” and “My Images”. Both of these icons are aliases

(shortcuts). The original items are found in “ScanWizard 5 Folder” with-

in the Macintosh HD. The ScanWizard 5 V.71 program activates the

scanner and the “My Images” folder stores the scanned images. You

should arrange the icons as shown on the image to the right.

Your desktop should resemble

the one shown above when the

software installation has concluded.

Preparing the Scanner and Connecting it to the Computer

4If the “ScanWizard 5 V5.71” alias is not

automatically created, you can create

one manually. Open the “ScanWizard 5

Folder” within the Macintosh HD and

click once to highlight the icon

“ScanWizard 5 V5.71”. Then, go to the

File menu and select “Make Alias”. This

will create an alias of the ScanWizard

application, as shown to the right. Place

this alias on the desktop.

Quick Ceph®Systems

Doc ID# 1033ScanMaker8700_Setup - Revision 4/ 3/0

Microtek ScanMaker 8700 Setup

http://www.quickceph.com/docs/1033ScanMaker8700_Setup.pdf

Once the software for the Microtek ScanMaker 8700 has been installed, you can begin scanning x-rays.

The following section covers the recommended settings for Quick Ceph 000 and Quick Ceph Image Pro.

Place the x-ray on the Glass Film Holder, as shown on the right. The

x-ray should be placed face-down on the glass with the nose facing

toward the back of the Film Holder. Slide the Glass Film Holder back

into the scanner. You are now ready to turn on the software.

Double click on the “ScanWizard 5 V5.71” icon to launch the scanner

software. The Standard Control Panel window for the scanner set-

tings will appear. Click on the red arrow icon in the upper right corner

of the control panel, as highlighted below to open the Advanced

Control Panel.

After the Advanced Control Panel appears, click on the face icon found

under the menu bar of the preview window and select the “Positive

Transparency” option. This turns on the transparency option.

Page

Setting up the Scanner Interface

Type of Image:

X-Ray images should be set to “Gray Scale (16-bit)” for bet-

ter quality.

Resolution:

The image resolution for Quick Ceph 000 is: 144 dpi

The image resolution for Quick Ceph Image Pro is: 7 dpi

Dimensions:

These are the marquee settings. To change these values, type

in the values shown below for the different Quick Ceph software.

Note: The units must initially be changed to pixels.

The recommended dimensions for Quick Ceph 000 are:

W: 1150 pixels x H: 1150 pixels at 100%

The recommended dimensions for Quick Ceph Image Pro are:

W: 5 0 pixels x H: 5 0 pixels at 100%

Image Rotation:

This button allows you to rotate the scanned images 90º

once they are scanned. This is necessary for QCIPro. For

QC 000, users can rotate the image 90º during the import of

the x-ray images.

On the Settings menu, adjust the scanner to the recommend-

ed settings, as shown below.

Note: Settings displayed are for QC 000.

Quick Ceph®Systems

Doc ID# 1033ScanMaker8700_Setup - Revision 4/ 3/0

Microtek ScanMaker 8700 Setup

http://www.quickceph.com/docs/1033ScanMaker8700_Setup.pdf Page 3

Scanning with the ScanMaker 8700

Overview Button:

Click this button once the scanner

settings have been entered to pre-

view the x-ray.

Image Correction:

If the image requires adjustment,

click on the Correction menu and

select the “Brightness and Contrast”

option to lighten or darken the x-ray,

The “Brightness and Contrast”

menu is shown below. The images

preview the effect of the changes.

To apply the changes, click on “OK”.

Saving the File:

Once the desired corrections have

been made to the image, you can

save the file. Click once on the

“Scan To” icon at the top of the pre-

view window.

By default, the image will be

scanned to a file, and the window

shown to the right will appear.

Hold down the Scan To button

brings up an option menu to allow

you to send the scanned image to

a different location, such as the

printer, for example.

Click on “Save” to save the image.

2This window displays

where the scanned files

will be saved to. By

default, it saves it to the

My Images folder,

which has a shortcut on

the desktop.

We recommend naming

the files with the name

of the patient, followed

by the type of x-ray.

This allows for easier

identification.

The file format should

be set to TIFF for high-

er image quality.

Otros manuales para ScanMaker 8700

Tabla de contenidos

Otros manuales de Escáner de Microtek

Microtek

Microtek ObjectScan 1600 Manual de usuario

Microtek

Microtek ArtixScanDI 3130c Manual de usuario

Microtek

Microtek ScanMaker 3700 Manual

Microtek

Microtek ScanMaker V6UPL Manual de usuario

Microtek

Microtek ScanMaker i900 Manual

Microtek

Microtek Artix Scan1100 Manual de instalación

Microtek

Microtek ScanMaker 4 Manual de usuario

Microtek

Microtek ArtixScan DI 2020 Manual de usuario

Microtek

Microtek ScanMaker 1000XL Plus Manual de usuario

Microtek

Microtek ScanMaker i800 Manual

Microtek

Microtek LS-4600 Manual de usuario

Microtek

Microtek ScanMaker 1000XL Manual de usuario

Microtek

Microtek ScanMaker 4600 Manual de usuario

Microtek

Microtek ScanMaker 4 Manual de instrucciones

Microtek

Microtek ScanMaker 3630 Manual de usuario

Microtek

Microtek ArtixScanDI 2015c Manual de usuario

Microtek

Microtek ScanMaker 3880 Manual de usuario

Microtek

Microtek Vantas 3100 Manual de usuario

Microtek

Microtek ScanMaker i460 Manual de instrucciones

Microtek

Microtek ScanMaker 1000XL Plus Manual de instrucciones

Microtek

Microtek LightLid 35 Manual de usuario

Microtek

Microtek XT3300 Manual de instrucciones

Microtek

Microtek ArtixScan DI 5230 Manual de instrucciones

Microtek

Microtek ScanMaker 8700 Pro Manual de usuario

Manuales populares de Escáner de otras marcas

Plustek

Plustek Scanner Manual de usuario

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manual de usuario

Renkforce

Renkforce DS100-5M Manual de usuario

Image Access

Image Access WideTEK A2 Manual de usuario

Canon

Canon imageFORMULA CR-120N Manual de usuario

Fujitsu

Fujitsu FI-4860C2 Manual de usuario

GeoSlam

GeoSlam ZEB Horizon Instrucciones de instalación

Kodak

Kodak i5800 Scanner Manual de usuario

Kodak

Kodak i7300 Manual de usuario

Revopoint

Revopoint POP Manual de usuario

Fujitsu

Fujitsu fi-4860C Manual de usuario

Eddyfi Technologies

Eddyfi Technologies Floormap X Manual de usuario

Faselase

Faselase F6 Manual de usuario

Fujitsu

Fujitsu CardMinder Manual de usuario

Uniden

Uniden BC340CRS Manual de usuario

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manual de usuario

Mustek

Mustek PageExpress 4800 Pro Manual de usuario

Optex

Optex 750830 Manual de usuario