Microtek ArtixScan DI 3130c Manual de instrucciones

Install Software

Unpack Contents

Unpack your scanner package and check for

major components.

Important: You must install software before

connecting your scanner.

Always close any open programs and turn off

Anti-virus utilities before installing software.

I49-005049 A, June 2016

A. Turn on your computer.

B. Place the Microtek Software CD/DVD into a drive, and follow the on-screen

instructions to install the scanner driver and software.

C. Restart your computer at the end of all software installation.

NOTE: If the Microtek Software Installer screen does not come up automatically, double-click the

following in succession: “My Computer”; the CD/DVD-ROM icon; then cdsetup.exe to start the

installer program.

Start Here

Installing your Microtek ArtixScan DI 3130c

1. ArtixScan DI 3130c scanner

2. Document feed tray

3. Hi-Speed USB cable

4. Software CDs/DVDs

5. Card Holder

6. Power adapter

7. Power cord

Install the Document Feed Tray

Before using the Document Feed Tray with your scanner, you need to install it on the

scanner. Follow the instructions and graphs below to correctly install the Document Feed

Tray.

A. Lift up the Release button in the

direction of the arrow shown to open

the scanner cover.

B. Install the Document Feed Tray on the

scanner;

a). insertthefouranges(tabs)of

the feed tray into the holes on the

scanner, indicated in the graphic by

blue circles.

b). pushdownthetwoanges(tabs)

located at the rear of feed tray into

another two holes, indicated in the

graphic by red circles.

Make sure the Document Feed Tray

snaps into place and sits tightly on the

scanner.

C. Close the scanner cover. You would

hear a click sound when the scanner

cover returns to its original position.

Connect Scanner

To the power adapter

A. Connect the power adapter to the back of the scanner.

B. Plug one end of the power cord into

the power adapter, and plug

the other end of the power cord into

a wall outlet or other power source.

To the Hi-Speed USB cable

C. Connect one end of the cable to your computer.

D. Connect the other end of the cable to the scanner’s USB port.

E. Turn the power switch at the back panel of your scanner to “On”; once the scanner

isdetectedbyyoursystem,theLED(green)willbrighten,andthescannerisreadyto

scan.

Customize the Function Button

The ArtixScan DI 3130c is equipped with one Select and one Enter buttons, used to

automateanumberofcustomizedandpredenedoperations,suchasscanningtoale,

sending an image to your printer, scanning for OCR, etc. Customizing is done through

the Scanner Button Settings interface in the ScanWizard DI, refer to the scanner’s User’s

Manual for more details.

Enter button

Select button

LED Display:

Show the selected

function number. • Select: Toggle through the number lists of

your preferred functions.

• Enter: Start scan and carry out the result

of the selected function number.

Position Documents

The scanner supports scanning of document in various materials, such as A4 printouts,

insurance papers, legal documents, postcards, credit cards, business cards, and etc. A

stack of up to 100 sheets can be fed in the scanner’s Document Feed Tray. Paper sizes

canrangefrom2.91”x2.1”(74mmx52mm)to8.5”x65”(216mmx1651mm).

To load a stack of documents

1. Pull out the Feed Tray Extender for

better paper support if needed.

2. Pull out the Output Tray to carry the

scanned documents. Flip up the Output

Tray Extender to carry the longer

documents if needed.

3. Load and center the stack of documents

onto the Document Feed Tray, with the

side to be scanned facing down and

the top edge facing toward the feeder.

Then, slide the two Guide Arms toward

the stacked papers if needed. Guide Arms

Output Tray Extender

Document Feed Tray

Feed Tray Extender

Output Tray

To Load Cards

1. Slide the Guide Arms toward the center

of the feed tray and free up the enough

space to put the Card Holder.

2. To install the Card Holder into the feed

tray, with its front side up, slide the

Card Holder along the sides of the Guide

Arms down until it completely hangs on

the arms.

After installed, there will be a slot

hollow space between the Card Holder

and the Document Feed Tray for loading

the card.

Guide Arms

Card Holder

PositionDocuments(Cont.)

3. Insert the card into the slot hollow

space between the Card Holder the feed

tray until it meets resistance, with the

side to be scanned facing up and the

top edge facing toward the feeder.

NOTE: When scanning a card, you have to

choose ADF (Duplex) in the Scan Source

drop-down menu as your image input device;

otherwise, it may cause incorrect or unwanted

results for your scanned images.

Basic Scanning

1. Load the document to be scanned into the document feed tray of the scanner.

WARNING: Do not place photo paper or fragile sheets of paper on the feed tray, as doing this

will damage the original photo or frail papers during the feeding process.

2. Launch ScanWizard DI as a stand-alone program by clicking on the ScanWizard DI icon

on the desktop.

3. Click the Scan Setup button in the interface to activate the Scan Setup interface.

4. In the Scan Setup interface, follow the steps below to specify your basic settings.

a) Select ADF (Front Side), ADF (Back Side) or ADF (Duplex)

in the Scan Source drop-down menu as your image input

device.

b) Select the appropriate image type in the Color Mode as

your image output type.

– Select RGB Color (24 bits) to scan the image in color.

– Select Grayscale (8 bits) to scan the image in

grayscale.

– Select Black & White (1 bit) to scan the image in black-and-white.

– Select Auto Color Detection to scan the image in color or non-color based on

the automatic judgement and detection of the system.

– Select Complex to scan the image in color, grayscale or non-color based on the

customization. Refer to the “The Scan Setup Interface” section in the back for

how to customize a desired image output type.

c) Select a dimension in the Paper Size as your preview

image size.

d) Select a desired resolution in the Resolution for your

image output resolution.

e) If necessary, select “Text Orientation Recognition” in the

Rotate menu to ensure the scanned images in a readable

orientation. When it is selected, you can select the

preferredlanguageusedasanidenticationintheoptions

menu.

f) If “Auto-crop” & “Auto-deskew” is selected, the

scanner automatically detects the size of the original

image,cropsthefullscanframetottheimage,

and removes unwanted black borders after the scan,

as well as corrects the distorted image for proper

alignment.

5. Click the Show Preview Window and Show Setting Window tabs in the Scan Setup

interface to display other interfaces which are helpful for your scanning processing.

6. Click the Preview button to perform a preliminary view of the entire image. When

done, a preview image appears in the Preview window.

Do not forget to put the document back on the document feed tray.

7. Go to the “General” panel by clicking the General tab in the Settings window. Specify

the settings for your requirements there.

a) If necessary, specify the image settings for the

front or back side of documents separately by

using the Sides of Material control when Scan

Sourceissetas“ADF(Duplex)”.

b) Select the image type in the Document Type as

your input image type.

– Select Photo to scan color prints.

– Select Text to scan text.

c) If necessary, check “Double Feed” to prevent multiple pages from being fed

together while papers are fed through the ADF.

d) If necessary, check “Remove Blank Page” and “Remove Punch Hole” to enhance

the quality of the scanned images.

8. Ifnecessary,gotothe“ImageProcess”panelbyclickingtheImage Process tab in

the Settings window. Use the image correction tools presented there to enhance the

imagequalityaccordingtoyourspecicrequirements.

9. Click the OK button to close the Scan Setup interface and return to the Main interface

of ScanWizard DI.

10. In the Main interface, click the File Formatmenubuttontoselectaleformatforthe

scanned images.

11. In the Main interface, click the File Namemenubuttontospecifyalenamingmethod

for the scanned images.

12. In the Main interface, select and click the Normal Scan button to start scanning.

 Whendone,thescannedimageswillbeautomaticallysavedintothefolderdenedin

the File Location menu box. At the same time, the scanned images will be displayed

inthumbnailsizesintheThumbnailViewwindowandlabeledwiththelenameand

leformatspeciedearlier.

13. Click the Open Folder button to locate the scanned images if you want to view.

NOTE: For more details on other scanning scenarios applicable to your scanner, refer to the scanner’s

User’s Manual in the Microtek Software CD/DVD.

APcontrolpanel(Maininterface)

TWAINdrivercontrolpanel(ScanSetupinterface)

File Location

menu box

Click on a

thumbnail image

to enlarge it in

the Image View

Window at the

right side of the

interface.

Fixing Paper Jams

1. Lift up the Release button in the

direction of the arrow shown to open

the scanner cover.

2. Remove the jammed paper by taking out

it in a forward-moving direction.

3. Close the scanner cover. You would

hear a click sound when the scanner

cover returns to its original position.

NOTE: Do not take out a jammed paper by force

from the scanner when the scanner cover closes.

If doing so, it may damage the rollers and cause

the scanner work improperly.

Scanner cover

Release button

Problems?

The LED on the scanner cover indicates the status of the scanner.

First,makesurethatyouhavefollowedSteps1to4asdescribedinthisguide(unpack,

install, connect). Then if your problem is listed here, try the suggested solution.

1. No light comes on when the scanner is turned on.

Make sure your scanner is connected to your computer and plugged into a power

source.

2. The Add/Remove Hardware Wizard appears on your screen.

Click the “Cancel” button and close the ScanWizard DI Control Panel. Disconnect

the Hi-Speed USB cable from the back of your computer, and refer to the installation

instructions in this guide or the ArtixScan DI 3130c User’s Manual.

3. When trying to scan, an error message appears on your screen that reads, “Can’t Find

Scanners”.

Make sure your scanner is connected to your computer and plugged into a power

source(seeStep4).

Uninstall and reinstall the ScanWizard DI software.

4. After clicking scan, a blank screen appears.

Uninstall and reinstall the ScanWizard DI software.

5. When trying to scan, an error message appears on your screen that reads, “Code -206,

ADF paper jam or roller failure.”

 ClickOKrst;thenopenthescannercover,asillustratedinthepervioussection“Fixing

Paper Jams”.

• Iftheproblemisoccurringfromapaperjam,followtheprocedureslaidoutinthe

“Fixing Paper Jams” section of this guide.

• Iftheproblemisoccurringfromsituationsotherthanapaperjam,followthe

procedures laid out in the “Position Documents” section.

Finally, close the scanner cover and restart scanning.

LED

Green On: Ready to scan.

Flashing Green: Scanning.

Red: Scanning errors happens.

Off: Scanner is off.

Tabla de contenidos

Otros manuales de Escáner de Microtek

Microtek

Microtek SCAN-IN-DEX 1000 Manual de usuario

Microtek

Microtek ArtixScan 120tf Manual de usuario

Microtek

Microtek ScanMaker 3700 Manual de usuario

Microtek

Microtek ArtixScan M2 Instrucciones de montaje

Microtek

Microtek ArtixScanDI 6240S Manual de usuario

Microtek

Microtek ScanMaker 1000XL Manual de usuario

Microtek

Microtek ArtixScanDI 3130c Manual de usuario

Microtek

Microtek ScanMaker i2400 Manual del propietario

Microtek

Microtek ScanMaker i450 Manual del propietario

Microtek

Microtek TMA 1600 Manual de usuario

Microtek

Microtek ScanMaker 8700 Manual de usuario

Microtek

Microtek ScanMaker 3700 Manual

Microtek

Microtek ArtixScan F2 Manual de instrucciones

Microtek

Microtek XT3300 Manual de instrucciones

Microtek

Microtek ArtixScan DI 2020 Instrucciones de montaje

Microtek

Microtek XT7000 HS Manual de usuario

Microtek

Microtek ArtixScan DI 2020 Manual de usuario

Microtek

Microtek ScanMaker 9700XL Manual de usuario

Microtek

Microtek ScanMaker 1000XL Manual de usuario

Microtek

Microtek ScanMaker 3750i Manual de usuario

Microtek

Microtek Vantas 3100 Manual de usuario

Microtek

Microtek ArtixScan 6000XY Manual de usuario

Microtek

Microtek Bio-5000 Plus Manual del propietario

Microtek

Microtek ScanMaker i700 Manual de usuario

Manuales populares de Escáner de otras marcas

Plustek

Plustek Scanner Manual de usuario

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manual de usuario

Renkforce

Renkforce DS100-5M Manual de usuario

Image Access

Image Access WideTEK A2 Manual de usuario

Canon

Canon imageFORMULA CR-120N Manual de usuario

Fujitsu

Fujitsu FI-4860C2 Manual de usuario

GeoSlam

GeoSlam ZEB Horizon Instrucciones de instalación

Kodak

Kodak i5800 Scanner Manual de usuario

Kodak

Kodak i7300 Manual de usuario

Revopoint

Revopoint POP Manual de usuario

Fujitsu

Fujitsu fi-4860C Manual de usuario

Eddyfi Technologies

Eddyfi Technologies Floormap X Manual de usuario

Faselase

Faselase F6 Manual de usuario

Fujitsu

Fujitsu CardMinder Manual de usuario

Uniden

Uniden BC340CRS Manual de usuario

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manual de usuario

Mustek

Mustek PageExpress 4800 Pro Manual de usuario

Optex

Optex 750830 Manual de usuario