Micromax X556 Manual de usuario
S120 L2 Service Manual
Please paste Handset Picture here
S120 L2 Service Manual
1. Technical Specifications :
Please fill below information in Remarks, Below given remarks are for reference only
Particular Remarks
Key Matrix For Flashing SPRD Flashing tool
Chipset SC6531DA
Android Version NA
Processor Frequency 900/1800MHz
Network Mode GSM
ROM 32Mb
RAM 32Mb
Internal memory 4MB
Expandable Memory 8GB
Factory mode code #*868*#
Good Earpiece value in ohms 32 Ohm
Good Loudspeaker value in ohms 8 Ohm
Good Mic value in ohms 330 Ohm
Good Vibrator value in ohms NA
2. CAUTIONS
I. Flashing & Servicing must be undertaken by qualified personnel only.
II. Ensure all work is carried out at an anti-static workstation and that an anti-static wrist strap is worn.
III. Use only approved Tools & components as specified in the parts list.
IV. Ensure all components, modules, screws, and insulators are correctly re-fitted after servicing and
alignment
V. Ensure all cables and wires are repositioned correctly if Handset disassembled
VI. Electrostatic discharge can easily damage the sensitive components of electronic products. Therefore,
Service Centre must adhere the precautions which mentioned above.
S120 L2 Service Manual
3. L2 Level trouble shooting
Please add trouble shooting/ Repairing steps against below given symptoms
Images must paste against every suggested troubleshooting hint
1）Main Components
LED BT
SPK
MIC
Motor
S120 L2 Service Manual
2）Display issue
NO
Description Reason Solution
SW FLASH THE SW
Soldering issue Re-soldering the LCD
LCD issue Change the LCD
1
Segments missing, Fading,
Contrast issue, Black lines, Color
issue, Backlight issue, Blank
display, Bad pixel, Flickering
CPU Refer to the service guide L3
2 Mechanically broken LCD issue Change the LCD
Back Camera
LCD
Receiver
S120 L2 Service Manual
3）Camera
NO
Description Reason Solution
Soldering issue Re-solder it
Camera issue Change it
1 Bad image
CPU Refer to the service guide L3
Soldering issue Re-solder it
Camera issue Change it
2 Camera not ready
CPU Refer to the service guide L3
Soldering issue Soldering issue
Camera issue Change camera
3 DEAD,No functionality
CPU CPU
4 Canot turn to front
camera Camera issue Change front camera
5 Canot turn to back
camera Camera issue Change back camera
LCD TESTING JIG
S120 L2 Service Manual
4）Speaker
NO
Description Reason Solution
The SPK with dust Clean the SPK
SPK foam issue Change it
Spk issue Change it
1 Noise/crack
CPU Refer to the service guide L3
Soldering issue Re-soldering it
SPK issue Change it
2 No volume
CPU Refer to the service guide L3
Soldering issue Re-soldering it
SPK issue Change it
3 Low volume
CPU Refer to the service guide L3
The volume of good SPK is 8Ω +/-0.5
Back camera with
flashlight
S120 L2 Service Manual
5）Microphone
NO
Description Reason Solution
Some dust with MIC Clean the MIC
Assembly issue Assembly it
MIC issue Change it
1 Noise with uplink side
CPUor related component Refer to the service guide L3
Soldering issue Re-solder it
MIC issue Change it
2
Volume low/no
volume with uplink
side
CPUor related component Refer to the service guide L3
3 TDD noise MIC issue Change it
SPK
S120 L2 Service Manual
1, The volume of good mic K is 2.2kΩ +/-0.5%2，Soldering temperature is 330+/-10℃
6）Receiver
NO
Description Reason Solution
There is dust with receiver Clean the receiver
Receiver issue Change it
1 Noise/crack
CPU Refer to the service guide L3
Connection issue Assembly it again
Receiver issue Change it
2 No voice/ volume low
CPU Refer to the service guide L3
MIC
S120 L2 Service Manual
1. The volume of RECEIVER is 32Ω +/-15% Ohm(at 1KHZ,179mV input)
7）Vibrator
NO
Description Reason Solution
Motor assembly issue Assembly it again
1 Vibrating is not
properly Motor issue Change it
Motor soldering issue Soldering it again
Motor issue Change it
2 No vibrating
CPU Refer to the service guide L3
The volume of good Vibrator is 30Ω +/-5%
Soldering temperature is 330+/-10℃
RECEIVER
S120 L2 Service Manual
8）Battery
NO
Description Reason Solution
the voltage of battery is less
than 3.3V
The voltage of battery is more than
1V, and its volume is 150mΩ+/
-10%,
then the battery is good, you can
charge it by DC power (
4V) directly
the voltage of battery is less
than 3.5V
Keep charging it until its voltage to be
3.7V
1 no output
the voltage of battery is 0 Change battery
the voltage of battery is less
than 3.5V
Keep charging it until its voltage to be
3.7V
the voltage of battery is 0 Change battery
2 no charging
CPU or charging IC with issue Refer to the service guide L3
3 Auto charging CPU or charging IC with issue Refer to the service guide L3
Motor
Otros manuales para X556
1
Tabla de contenidos
Otros manuales de Teléfono móvil de Micromax
Micromax
Micromax Q7 Manual de usuario
Micromax
Micromax Q427+ Guía de referencia
Micromax
Micromax X118 Manual de usuario
Micromax
Micromax Canvas 2 Colours A120 Manual de usuario
Micromax
Micromax A111 Manual de usuario
Micromax
Micromax Q66- Eclipse Manual de usuario
Micromax
Micromax Unite 3 Manual de usuario
Micromax
Micromax X081 Manual de usuario
Micromax
Micromax A104 Manual
Micromax
Micromax A69 Manual de usuario
Micromax
Micromax W900 Manual de usuario
Micromax
Micromax A190 Manual
Micromax
Micromax S300 Manual de usuario
Micromax
Micromax Bolt D200 Manual de usuario
Micromax
Micromax A54 Manual de usuario
Micromax
Micromax A62 Manual de usuario
Micromax
Micromax E4817 Manual de usuario
Micromax
Micromax X275 Manual de usuario
Micromax
Micromax A66 Manual de usuario
Micromax
Micromax Q346 Manual de usuario
