Micromax Q452 Manual de usuario
Q452 L3 Service Manual
1：Technical Specifications
Particular
Remarks
Key Matrix For Flashing
NA
Chipset
MT6737
Android Version
Android M
Frequency
Quad Core, 1.1GHz LTE CAT4
Network Mode
850MHz/900MHz/1800MHz/1900MHz
3G Band
B1,B8,B5
4G Band
B3,B7,B8
ROM
16G
RAM
2G
Internal SD Card memory
10.8G
Expandable Memory
64G
Factory mode code
Press Vol-/ power key at the same time
Good Earpiece volume
32Ω± 15%
Good Loudspeaker volume
8Ω± 5%
Good MIC volume
2.2kΩ± 5%
Good Vibrator volume
30Ω± 5%
2：CAUTIONS
I. Flashing & Servicing must be undertaken by qualified personnel only.
II. Ensure all work is carried out at an anti-static workstation and that an anti-static wrist strap is worn.
III. Use only approved Tools & components as specified in the parts list.
IV. Ensure all components, modules, screws, and insulators are correctly re-fitted after servicing and
alignment
V. Ensure all cables and wires are repositioned correctly if Handset disassembled
VI. Electrostatic discharge can easily damage the sensitive components of electronic products. Therefore,
Service Centre must Adhere the precautions which mentioned above.
3. L3 Service Manual
RF 2G PA
（U1200）
（）
Flash
（U401）
CPU
（U400）
BT/WIFI/GPS/
FM
( U1300)
Receiver
Connector
（SC4/SC5）
Main camera
connector
(J1501)
P-Sensor
( U1703)
XTAL
（Y801）
Power IC
(U601)
USB
Connector
（J1804）
3/4G PA
Backlight driver
(U1401)
RF IC
（U800）
（）
1. Unable to load Software:
Solution:
First check the computer can recognize the device or not, if not, Re-load it.
Then check the USB port to master control circuit is normal or not.：format the flash and upgrade again if fail in
the Proceed of downloading.
Use a fresh data cable
Earphone
Connector
(J1601）
Switch
charge IC
(U1802)
Audio PA
(U1600)
LCD
Connector
(J800)
Front Camera
connector
(J1500)
TP
connector
(J1402)
SIM
connector
(J1800)
Side KEY
connector
(J703)
Battery
connector
(J1802)
T-Flash
connector
(J1803)
Flashlight
driver
(U1502)
Flashlight
(D1502)
SIM
connector
(J1801)
4G NET
ANT
(E1101/E1102
)
WIFI/BT/GPS
ANT
(E1300/E1301)
G-Sensor
(U1700)
Check the I/O connector soldering quality, if not , Re-sold it or change it.
Check the CPU work normally or not. Re-Solder the CPU or change it
USB
Connector
CPU
Flash
2. No power on
Solution:
Flash the handset with latest SW
Check the battery have capacity or not ,if not ,Change it
Charging with transferred to 4.0 V dc power supply to the mainboard on battery Re-soldering ,check
The mainboard work current, the normal starting current will be from 100 ma jump to light screen
Enter boot LOGO 400 ma to completely started around 500 ma, if the current not right then check
Whether has short circuit or open circuit phenomenon or not.
Check the Power IC work normally or not ,Re-Solder it or change it
The output voltage normally or not
Check the 26M crystal work normally or not ,Re-Solder it or change it
Check the CPU work normally or not, Re-Solder CPU or change it
26M
crystal
CPU
Power
IC
3. Not charging:
Solution:
Flash the handset with latest SW
Plug in the charger to check whether the machine has a charging icon, if don’t have, then check the
5V power pin of USB port connect the mainboard or not
Check the voltage of battery when charging If it reaches 4.2V, has shown in front of the
Transmission, now maybe is the battery bad so that no charging.
Check the I/O connector work well or not ,if not , Re-Solder or change it
Check the charging switch work well or not ,if not , Re-Solder or change it
Check the Power IC work normally or not, Re-Solder CPU or change it
Check the CPU work normally or not. Re-Solder the CPU or change it
I/O
connector
Power IC
Switch
Charging IC
switch IC
4. LCD / Display problem:
Solution:
Flash the handset with latest SW
Check the connect ribbon cable saddle normally or not , Re-assembly LCD.
Check the LCD connector work normally or not, Re-Solder LCD connector or change it
Check the CPU work normally or not, Re-Solder CPU or change it
.
CPU
LCD
connector
5. Touch panel is not working
Flash the handset with latest SW
Check the connect ribbon cable saddle normally or not , Re-assembly TP.
Check the TP connector work normally or not, Re-Solder TP connector or change it
Check the CPU work normally or not, Re-Solder CPU or change it
TP
connector
CPU
Otros manuales de Teléfono móvil de Micromax
Micromax
Micromax X225 Manual de usuario
Micromax
Micromax X550-Qube Manual de usuario
Micromax
Micromax A54 Manual de usuario
Micromax
Micromax A065 Manual de usuario
Micromax
Micromax Canvas Hue 2 A316 Manual de usuario
Micromax
Micromax A190 Manual de usuario
Micromax
Micromax A114 Manual de usuario
Micromax
Micromax X771 Manual de usuario
Micromax
Micromax A80 Manual de usuario
Micromax
Micromax A47 Manual de usuario
Micromax
Micromax GC232 Manual de usuario
Micromax
Micromax X660 Manual de usuario
Micromax
Micromax X245 Manual de usuario
Micromax
Micromax A310 Manual de usuario
Micromax
Micromax AE90 Manual de usuario
Micromax
Micromax GC256 Manual de usuario
Micromax
Micromax A069 Manual de usuario
Micromax
Micromax X220 Manual de usuario
Micromax
Micromax Q427+ Manual de usuario
Micromax
Micromax E4817 Manual de usuario
