Microchip Technology ATtiny416 Xplained Nano Manual de usuario
ATtiny416 Xplained Nano
ATtiny416 Xplained Nano Evaluation Kit User's Guide
Preface
The ATtiny416 Xplained Nano Evaluation Kit is a hardware platform to evaluate the ATtiny416 microcontroller.
Supported by the Atmel Studio and MPLAB® X integrated development platform, the kit provides easy access to the
features of the ATtiny416 and explains how to integrate the device into a custom design.
The Xplained Nano series of evaluation kits include an on-board mini embedded programmer, and no external tools
are necessary to program the ATtiny416.
© 2019 Microchip Technology Inc. User Guide DS50002683B-page 1
Table of Contents
Preface........................................................................................................................................................... 1
1. Introduction............................................................................................................................................. 3
1.1. Features....................................................................................................................................... 3
1.2. Kit Overview................................................................................................................................. 3
2. Getting Started........................................................................................................................................ 4
2.1. Xplained Nano Quick Start........................................................................................................... 4
2.2. Design Documentation and Relevant Links................................................................................. 4
3. Xplained Nano.........................................................................................................................................6
3.1. Mini Embedded Debugger............................................................................................................6
3.2. Power Sources............................................................................................................................. 6
3.3. Xplained Nano Standard Pinout................................................................................................... 7
3.4. Disconnecting mEDBG.................................................................................................................8
4. Hardware User Guide............................................................................................................................. 9
4.1. Connectors...................................................................................................................................9
4.2. Current Measurement.................................................................................................................. 9
4.3. Peripherals................................................................................................................................. 10
5. Embedded Debugger Implementation...................................................................................................11
5.1. UPDI........................................................................................................................................... 11
5.2. Virtual COM Port.........................................................................................................................11
6. Hardware Revision History and Known Issues..................................................................................... 12
6.1. Identifying Product ID and Revision........................................................................................... 12
6.2. Fuse masking............................................................................................................................. 12
6.3. Revision 4...................................................................................................................................12
7. Document Revision History...................................................................................................................13
The Microchip Website.................................................................................................................................14
Product Change Notification Service............................................................................................................14
Customer Support........................................................................................................................................ 14
Microchip Devices Code Protection Feature................................................................................................ 14
Legal Notice................................................................................................................................................. 14
Trademarks.................................................................................................................................................. 15
Quality Management System....................................................................................................................... 15
Worldwide Sales and Service.......................................................................................................................16
ATtiny416 Xplained Nano
© 2019 Microchip Technology Inc. User Guide DS50002683B-page 2
1. Introduction
1.1 Features
• ATtiny416 Microcontroller
• One Yellow User LED
• One Mechanical Button
• mEDBG
– Auto-ID for board identification in Atmel Studio/Microchip MPLAB® X IDE
– One green board status LED
– Programming
– Virtual COM port (CDC)
• USB Powered
1.2 Kit Overview
The Microchip ATtiny416 Xplained Nano Evaluation Kit is a hardware platform to evaluate the ATtiny416.
Figure 1-1. ATtiny416 Xplained Nano Evaluation Kit Overview
NC
UPDI
NC
NC
VREG
VUSB
GND
CLK OUT
CDC TX
CDC RX
VCC
PA0
PA1
PA2
PA3
PA4
PA5
GND
PC3
PC2
PC1
PC0
PB0
PB1
Micro USB Connector
User LED User button
mEDBG
(ATmega32U4)
ATtiny416
Power disconnect mEDBG dis connectStatus LED
UPDI
USER L ED USER BTN
CDC T X
CDC RX
Power
Ground
Clock
Serial
Target I/O
Shared I/Os
Program/Debug
PA6
PA7
PB5
PB2
PB3
PB4
ATtiny416 Xplained Nano
Introduction
© 2019 Microchip Technology Inc. User Guide DS50002683B-page 3
2. Getting Started
2.1 Xplained Nano Quick Start
Steps to start exploring the Microchip Xplained Nano platform:
1. Download Atmel Studio/Microchip MPLAB® X IDE.
2. Launch Atmel Studio/Microchip MPLAB® X IDE.
3. Optional: Use MPLAB® Code Configurator or Atmel START to generate drivers and examples.
4. Write your application code.
5. Connect a USB cable (Standard-A to Micro-B or Micro-AB) between the PC and the debug USB port on the
kit.
When the Xplained Nano kit is connected to your computer for the first time, the operating system will perform a
driver software installation. The driver file supports both 32- and 64-bit versions of Microsoft® Windows® XP,
Windows Vista®, Windows 7, Windows 8, and Windows 10. The drivers for the kit are included with Atmel Studio/
Microchip MPLAB® X IDE.
Once the Xplained Nano board is powered, the green status LED will blink and Atmel Studio/Microchip MPLAB® X
IDE will auto-detect which Xplained Nano board is connected. Atmel Studio/Microchip MPLAB® X IDE will present
relevant information like data sheets and kit documentation. The ATtiny416 device is programmed and debugged by
the on-board Mini Embedded Debugger and therefore, no external programmer or debugger tool is required.
2.2 Design Documentation and Relevant Links
The following list contains links to the most relevant documents and software for the ATtiny416 Xplained Nano.
•Xplained Products - Xplained Evaluation Kits are a series of easy-to-use evaluation kits for Microchip
microcontrollers and other Microchip products.
– Xplained Nano - used for low pin count devices and provides a minimalistic solution with access to all I/O
pins of the target microcontroller.
– Xplained Mini - used for medium pin count devices and adds Arduino Uno compatible header footprint and
a prototyping area.
– Xplained Pro - used for medium-to-high pin count devices that features advanced debugging and
standardized extensions for peripheral functions.
Note: All the above kits have on-board programmers/debuggers, which creates a set of low-cost boards for
evaluation and demonstration of features and capabilities of different Microchip products.
•Atmel Studio - Free IDE for the development of C/C++ and assembler code for microcontrollers.
•MPLAB® X IDE - MPLAB® X IDE is a software program that runs on a PC (Windows®, Mac OS®, Linux®) to
develop applications for Microchip microcontrollers and digital signal controllers. It is called an Integrated
Development Environment (IDE) because it provides a single integrated “environment” to develop code for
embedded microcontrollers.
•MPLAB® Code Configurator - MPLAB® Code Configurator (MCC) is a free software plug-in that provides a
graphical interface to configure peripherals and functions specific to your application.
•IAR Embedded Workbench® for AVR® - This is a commercial C/C++ compiler that is available for 8-bit AVR.
There is a 30-day evaluation version as well as a 4 KB code-size-limited kick-start version available from their
website.
•Atmel START - Atmel START is an online tool that helps the user to select and configure software components
and tailor your embedded application in a usable and optimized manner.
•Microchip Sample Store - Microchip sample store where you can order samples of devices.
•Data Visualizer - Data Visualizer is a program used for processing and visualizing data. The Data Visualizer
can receive data from various sources such as the EDBG Data Gateway Interface found on Curiosity Nano and
Xplained Pro boards and COM Ports.
•ATtiny416 Xplained Nano website - Kit information, latest user guide and design documentation.
ATtiny416 Xplained Nano
Getting Started
© 2019 Microchip Technology Inc. User Guide DS50002683B-page 4
3. Xplained Nano
Xplained Nano is an evaluation platform that provides a set of small boards with access to all microcontroller I/O’s.
The platform consists of a series of low pin count Microcontroller (MCU) boards, which are integrated with Atmel
Studio/Microchip MPLAB® X IDE to present relevant user guides, application notes, data sheets, and example code
through Atmel Studio/Microchip MPLAB® X IDE. The platform also features a Virtual COM port for serial
communication to a host PC.
3.1 Mini Embedded Debugger
The ATtiny416 Xplained Nano contains the Mini Embedded Debugger (mEDBG) for on-board programming and
debugging. The mEDBG is a composite USB device of two interfaces: a debugger and a virtual COM port.
Together with Atmel Studio, the mEDBG debugger interface can program and debug the ATtiny416. On ATtiny416
Xplained Nano, the UPDI interface is connected between the mEDBG and the ATtiny416.
The virtual COM port is connected to a UART on the ATtiny416 and provides an easy way to communicate with the
target application through the terminal software. It offers variable baud rate, parity, and Stop bit settings.
Note: The settings on the ATtiny416 must match the settings given in the terminal software.
Info: The virtual COM port in the mEDBG requires the terminal software to set the Data Terminal Ready
(DTR) signal to enable the UART pins connected to the ATtiny416. If the DTR signal is not enabled the
UART pins on the mEDBG are kept in high-z (tri-state), rendering the COM port unusable. The DTR signal
is automatically set by some terminal software, but it may have to be manually enabled in the target
terminal.
The mEDBG controls one status LED on the ATtiny416 Xplained Nano. The table below shows how the LED is
controlled in different operation modes.
Table 3-1. mEDBG LED Control
Operation Mode Status LED
Power-up LED is briefly lit
Normal operation LED is not lit
Programming Activity indicator; the LED flashes when programming/
debugging with the mEDBG
3.1.1 Xplained Nano Clock Output
The mEDBG outputs its CPU clock to the CLK pin 8, as shown in 3.3 Xplained Nano Standard Pinout. The clock
output can be used to feed the target device with a more accurate clock if this is needed for the application.
3.2 Power Sources
The kit can be powered by different sources. By default the kit will have a 5V supply and the voltage is taken directly
from the USB port through a 500 mA PTC fuse. The voltage from the USB connector can vary between 4.4V to 5.25V
(according to USB spec).
If other voltages are required, the kit must be disconnected from the USB to avoid damage or contention to the USB
power. The mEDBG must also be disconnected from the target section of the board. The board can be powered by
applying a voltage to one of the power connections on the board, according to the table below. To avoid any power
leakage through the mEDBG, this should also be disconnected by removing the resistors shown in Figure 3-3. For
placement of power connections, see 3.3 Xplained Nano Standard Pinout.
ATtiny416 Xplained Nano
Xplained Nano
© 2019 Microchip Technology Inc. User Guide DS50002683B-page 6
Table 3-2. Power Connections
Power Connection Description
VUSB USB Voltage output when USB is connected (behind a PTC fuse). Can be used as power
input when USB is not used.
VREG Regulated voltage from VUSB. If the kit does not have a regulator, this is directly connected
to VUSB.
VCC Target voltage supply. By default, connected to VREG through a 0Ω resistor. Apply external
voltage here if the resistor is removed.
Figure 3-1. Power Supply Block Diagram
USB Target MCUPTC
Power source
Power connection
Power consumer
0-ohm Resistor
VUSB /
VREG VCC
mEDBG
3.3 Xplained Nano Standard Pinout
Xplained Nano kits have a standard pinout in the mEDBG section, as shown in the tables and figure below. The
program/debug pins will change depending on the target interface but will remain at the same locations.
Xplained Nano kits have a target section where all I/O pins will be available and fanned out. Except for the VCC and
GND pins with fixed positions, there are no defined pin functions in this area. The first pin in the target area is the
VCC pin, located right next to the VREG pin of the standard section. The last pin is GND, and it is located next to the
CDC RX pin in the standard section. For reference, see the figure below.
3.3.1 Standard Pinout for UPDI
Table 3-3. Xplained Nano Standard Pinout for UPDI
Pin Number Name Description
1 NC No Connect
2 UPDI UPDI program/debug line
3 NC No Connect
4 NC No Connect
5 VREG Regulated voltage or VUSB if no regulator present
6 UART RX mEDBG UART RX line
7 UART TX mEDBG UART TX line
8 CLK mEDBG clock output
9 GND Ground
10 VUSB USB voltage
ATtiny416 Xplained Nano
Xplained Nano
© 2019 Microchip Technology Inc. User Guide DS50002683B-page 7
Figure 3-2. Xplained Nano Standard Pinout for UPDI
NC
UPDI
NC
NC
VREG
VUSB
GND
CLK OUT
CDC TX
CDC RX
VCC GND
Micro USB ConnectormEDBGPower disconnect Status LED
3.4 Disconnecting mEDBG
The target device can be completely separated from the mEDBG, but this requires some small modifications to the
board using a soldering iron. By removing the resistors in the sections shown in the figure below, the mEDBG is
completely disconnected from the target controller. If desired to connect the mEDBG again, solder in 0Ω resistors or
solder in 100-mil headers on the header footprints and use wire-straps to connect the interfaces.
Figure 3-3. Kit Modifications
Power disconnect mEDBG disconnect
ATtiny416 Xplained Nano
Xplained Nano
© 2019 Microchip Technology Inc. User Guide DS50002683B-page 8
4. Hardware User Guide
4.1 Connectors
4.1.1 ATtiny416 Xplained Nano Pinout
The ATtiny416 Xplained Nano has a direct fan-out of the I/O pins of the device and all I/O’s are accessible at the
edge connectors.
Table 4-1. Edge Connector
Edge
Connector
ATtiny416 Pin Functions Shared Functionality
1 VCC Power supply
2 PA[0] ADC0_0/UPDI/RESET mEDBG UPDI
3 PA[1] ADC0_1/MOSI0/TxD0/SDA0 mEDBG CDC TX
4 PA[2] ADC0_2/MISO0/EVOUT0/RxD0/SCL0 mEDBG CDC RX
5 PA[3] ADC0_3/SCK0/WO3/CLKIN/XCK0
6 PA[4] ADC0_4/ADC1_0/XY0/SS0/WOA/XDIR
7 PA[5] ADC0_5/ADC1_1/XY1/ACOUT/WO4/WOB
8 PA[6] ADC0_6/ADC1_2/XY2/ACN0/DACOUT/WO5
9 PA[7] ADC0_7/ADC1_3/XY3/ACP0/
10 PB[5] ADC0_8/ACN1/CLKOUT/WO2 User LED
11 PB[4] ADC0_9/ACP1/WO1 User button
12 PB[3] TOSC1/EVOUT1/RxD0/WO0
13 PB[2] TOSC2/TxD0/WO2
14 PB[1] ADC0_10/XY4/XCK0/SDA0/WO1
15 PB[0] ADC0_11/XY5/XDIR0/SCL0/WO0
16 PC[0] ADC1_6/WOC/SCK0
17 PC[1] ADC1_7/WOD/MISO0
18 PC[2] ADC1_8/EVOUT2/MOSI0
19 PC[3] ADC1_9/SS0/WO3
20 GND Ground
4.2 Current Measurement
The power to the target controller ATtiny416 is connected from the VREG supply to the targets VCC supply with a 0Ω
resistor, as shown in the figure below. To measure the power consumption of the device, remove the 0Ω resistor and
replace it with an ammeter. The ammeter can be connected between the VREG and VCC pads for easy
measurement.
ATtiny416 Xplained Nano
Hardware User Guide
© 2019 Microchip Technology Inc. User Guide DS50002683B-page 9
Tip: To connect the two power domains again, solder in a 0Ω resistor on the footprint or a 100-mil header
on the header footprint at the edge of the board and place a jumper between VREG and VCC.
CAUTION
Removing the resistor while the kit is powered without an ammeter or jumper may cause the ATtiny416 to
be powered through its I/O pins. This may cause permanent damage to the device.
Figure 4-1. Current Measurement
VREG
VCC
Power disconnect
4.3 Peripherals
4.3.1 LED
There is one yellow LED available on the ATtiny416 Xplained Nano board that can be turned ON and OFF. The LED
can be activated by driving the connected I/O line to GND.
Table 4-2. LED Connection
ATtiny416 Pin Function Shared Functionality
PB5 Yellow LED0 Edge connector
4.3.2 Mechanical Buttons
ATtiny416 Xplained Nano contains one mechanical button. This is a generic user configurable button and when a
button is pressed it will drive the I/O line to GND.
Info: There is no pull-up resistor connected to the generic user button. Remember to enable the internal
pull-up in the ATtiny416 to use the button.
Table 4-3. Mechanical Button
ATtiny416 Pin Description Shared Functionality
PB4 User button Edge connector
ATtiny416 Xplained Nano
Hardware User Guide
© 2019 Microchip Technology Inc. User Guide DS50002683B-page 10
Tabla de contenidos
Otros manuales de Placa madre de Microchip Technology
Microchip Technology
Microchip Technology MIC4802 Manual de usuario
Microchip Technology
Microchip Technology MCP1663 Manual de usuario
Microchip Technology
Microchip Technology dsPICDEM MCSM Manual de usuario
Microchip Technology
Microchip Technology UCS81003 Manual de usuario
Microchip Technology
Microchip Technology EVB-LAN7500-LC Manual de usuario
Microchip Technology
Microchip Technology UCS2112 Manual de usuario
Microchip Technology
Microchip Technology MCP6 series Manual de usuario
Microchip Technology
Microchip Technology MCP3911 Manual de usuario
Microchip Technology
Microchip Technology MCP73855 Manual de usuario
Microchip Technology
Microchip Technology WINC1500 Manual de usuario
Microchip Technology
Microchip Technology PICDEM Manual de usuario
Microchip Technology
Microchip Technology PIC32CM LE00 Manual de usuario
Microchip Technology
Microchip Technology SAM D21 Manual de usuario
Microchip Technology
Microchip Technology SAM L10 Xplained Pro Manual de usuario
Microchip Technology
Microchip Technology MCP19114 Manual de usuario
Microchip Technology
Microchip Technology MCP651 Manual de usuario
Microchip Technology
Microchip Technology MCP1664 Manual de usuario
Microchip Technology
Microchip Technology MCP2221 Manual de usuario
Microchip Technology
Microchip Technology dsPICDEM MCLV-2 Manual de usuario
Microchip Technology
Microchip Technology MIC23356 Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
