Microchip Technology PICDEM Manual de usuario

PICDEM™ Mechatronics Demo Board

Quick Start Guide

The PICDEM Mechatronics Demo Board is programmed at the factory with a demonstration program. The board must

be conﬁgured as described in this chapter in order to use the demonstration program. Once the board is conﬁgured

and powered up, the speed of the Brushed DC (BDC) motor on the board may be varied using the potentiometer

(POT1). The 8-bit hexadecimal interpretation of the position of POT1 is displayed on the LCD.

Board Setup

Using the provided wire jumpers, screwdriver and shunts (2-pin black hard plastic jumpers), conﬁgure the

board as shown in the Quick Board Setup Schematic.

1. Attach the leads of the brushed DC motor to Drive 1 and Drive 2 using the screwdriver.

2. Connect POT1 (on J4) to C1- (on J13) using a wire jumper.

3. Connect P1 (on J1) to RD7 (on J10) using a wire jumper.

4. Connect N2 (on J1) to RD2/CCP2 (on J10) using a wire jumper.

5. Connect +5 VDC to the center pin on JP8 using a shunt.

Board Power-Up

Supply power to the board in one of the following ways:

• Connect a 9-12 VDC (0.75 amp minimum) supply using J9 (see note below)

• Connect a 9-12 VDC (0.75 amp minimum) supply to the P21 and P20 screw terminals.

• Connect a 9 VDC battery to the battery connector.

• Connect a 5 VDC (1.2 amp minimum) supply to TP2 and TP3.

Demonstration Program

Press CLR FAULT (SW5), which is near the bottom right corner of the board. Turn POT1 clockwise to

increase the speed of the motor. Note that the number displayed on the LCD increases as you turn the

potentiometer clockwise.

Try experimenting with the other sensors on the board:

• Move the jumper wire on POT1 (J4) to Light (J4). Vary the intensity of light shining on the light sensor

located near the top left corner of the board. Notice what happens to the motor.

• Move the same jumper wire to TEMP (J4). Blow on the temperature sensor located on the top left corner

of the board. Note what happens to the number displayed on the LCD.

• Move the jumper wire back to POT1. Move the jumper wire from N2 (J1) to D0 (J14). Watch what

happens to the intensity of LED D0 as you turn the potentiometer.

Microchip Technology Inc. •2355 W. Chandler Blvd. •Chandler, AZ 85224-6199 USA •(480) 792-7200 •FAX (480) 792-7277

The Microchip name and logo, and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. In-Circuit Serial

Programming, ICSP and PICDEM are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. All other trademarks mentioned herein are property of

DS51562B *DS51562B*

Quick Board Setup Schematic

Tabla de contenidos

Otros manuales de Placa madre de Microchip Technology

Microchip Technology

Microchip Technology MCP6 series Manual de usuario

Microchip Technology

Microchip Technology MCP4725 SOT-23-6 Manual de usuario

Microchip Technology

Microchip Technology MCP1726 Manual de usuario

Microchip Technology

Microchip Technology MCP1633 SEPIC Manual de usuario

Microchip Technology

Microchip Technology EVB-USB5744 Manual de usuario

Microchip Technology

Microchip Technology ATSAMB11 Manual de usuario

Microchip Technology

Microchip Technology AVR-BLE Manual de instalación

Microchip Technology

Microchip Technology SAM D21 Manual de usuario

Microchip Technology

Microchip Technology SAM L10 Xplained Pro Manual de usuario

Microchip Technology

Microchip Technology MCP2221 Manual de usuario

Microchip Technology

Microchip Technology ATECC608A Manual de usuario

Microchip Technology

Microchip Technology PAC1934 Manual de usuario

Microchip Technology

Microchip Technology MCP6S2 Series Manual de usuario

Microchip Technology

Microchip Technology RN-2483-PICtail Manual de usuario

Microchip Technology

Microchip Technology MCP39F521 Manual de usuario

Microchip Technology

Microchip Technology PIC18F57Q84 Curiosity Nano Manual de instalación

Microchip Technology

Microchip Technology EVB-USB7056 Manual de usuario

Microchip Technology

Microchip Technology PIC18F46J50 Manual de usuario

Microchip Technology

Microchip Technology dsPICDEM MCSM Manual de usuario

Microchip Technology

Microchip Technology ATmega4809 Xplained Pro Manual de usuario

Microchip Technology

Microchip Technology EVB-LAN9252-3PORT Manual de usuario

Microchip Technology

Microchip Technology 28-Pin LIN DM164120-3 Manual de usuario

Microchip Technology

Microchip Technology MCP1664 Manual de usuario

Microchip Technology

Microchip Technology PRO MATE II Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario