Mi-Light MiBOXER FUT041 Manual de usuario
Single Color LED Strip Controller (433MHz )
Model No.: FUT041
Subordinate New Brand
This controller adopt the widely used 433MHz wireless
technology with the features of low power consumption, long
signal transmitting and strong anti-interference, etc. Widely
used on the controlling of hotel lighting and home lighting.
Features
37.5mm 22mm55.5mm
119mm
114mm
22mm
Input 1 (DC
5.5*2.1mm
)
Pilot lamp
Input 2
433MHz RF wireless
transmission technology
Remote control
Control distance 30m
Dimmable
control
Parameters
Products Key Diagram
Working Voltage: 3V(2*AAA Battery)
Working Temp.: -20~60°C
RF: 433MHz
Standby Power: 20uA
Transmitting Power: <10mW
Modulation Method: ASK
Control Distance: 30m
Remote Control
Input Voltage: DC12V~24V
Output: 12A/Channel
Total Output: Max 12A
Working Temp.: -20~60°C
RF: 433MHz
Control Distance: 30m
Output Connection: Common anode
Strip Controller
Maximum brightness
Minimum brightness
Medium brightness
Dimming ring
Lowest
ON
OFF
Highest
Factory setting is one remote control one receiver. Users can group it
as per the need. One remote can control countless receivers,but one
receiver just can bel controlled by max 4 remotes.
Connect diagram
Always lighting means working normally; Flash means receiving remote
signal.
Input: DC12V/24V
V- V+
V+
W
Single Color LED Strip Controller
(433MHz)
Model No.: FUT041
Input Voltage: DC12V~24V
Output: 12A/Channel
Total Output: Max 12A
Made in China
Working Temp.: -20~60°C
RF: 433MHz
Controlling Distance: 30m
V+W
OUTPUT
Pilot lamp instruction:
Note
ON
OFF
Linking the controller
Unlinking the controller
The light blink 3 times slowly means the linking is done successfully.
If the light not blink slowly, the linking failed, Pls switch off
the light again, and follow the above steps again.
When the light on, short press
" " 1 time within 3 seconds.
Switch off the light, after 10
seconds switch on again.
+
W
Power
Supply
controller
The light blinking 6 times quickly, means the unlinking successfully.
If the light not blink quickly, the unlink failed, pls switch off
the light again, and follow the above steps to unlink again.
Switch off the light, after 10
seconds switch on again.
Link/Unlink
button
+
W
Power
Supply
controller
When the light on, short press
" " 5 times within 3 seconds.
ON
OFF
Link/Unlink
button
Attention
1. Please check whether the input voltage of the constant voltage
power supply is in accordance with the controller, and please
check the connection of both the cathode and anode,
otherwise the controller will be damage.
2. Please don’t connect wires with power on. Please turn on
again only when it is in right connection and no short circuit.
3. Non-professional user cannot dismantle the controller directly,
otherwise it may damage the controller.
4. Please do not use the controller in the place with widely range
metal area or strong electromagnetic wave nearby, otherwise,
the remote distance will be seriously affected.
When the light on, short press
" " 5 times within 3 seconds.
Made in China
Tabla de contenidos
Otros manuales de Controladores de Mi-Light
Mi-Light
Mi-Light FUT086 Manual de usuario
Mi-Light
Mi-Light MiBoxer FUT037SA Manual de usuario
Mi-Light
Mi-Light FUT089 Manual de usuario
Mi-Light
Mi-Light SYS-PT1 Manual de usuario
Mi-Light
Mi-Light MiBOXER RGB-MZ Manual de usuario
Mi-Light
Mi-Light MiBOXER LC2-ZR Manual de usuario
Mi-Light
Mi-Light FUT092 Manual de usuario
Mi-Light
Mi-Light MiBoxer FUT039SA Manual de usuario
Mi-Light
Mi-Light MiBOXER FUT035S Manual de usuario
Mi-Light
Mi-Light MIBOXER FUT035Z Manual de usuario
