Mi-Light Fullwat TRIAC CONTROL Manual de usuario

Owners manual

TRIAC CONTROL

Smart LED control system

Dimming Controller for LED systems and conventional lighting systems

by means of an end-of-phase triac system (ELV) with push button.

Compatible with Alexa and Google Home through LENNY-WIFOX1 gateway.

TRIAC CONTROL

Smart LED control system

TRIAC controller

Modelo LENNY-TRIAC1

Input voltage AC 100-240V 50/60Hz

Output voltage AC 100-240V

Output current MAX 1.36A

Output power 150W@100VAC;

300W@240VAC

Regulation method Wireless RF, push button, APP

RF range 30m

Working temperature -10-40ºC

WiFi gateway

Model LENNY-WIFOX1

Working voltage DC5V/500mA (Micro USB)

Working temperature -20~60°C

Communication WiFi-IEEE 802.11b/g/n 2.4GHz

Working frequency 2.4GHz

Transmission power 6dBm

* Suggested AC/DC adaptors (not included): MWMU10GS

FU-ADPY10-5-USB

Control rotativo

Modelo LENNY-PAN-K1

Tensión de trabajo 3V (batería CR2032)

Potencia de transmisión 6dBm

Consumo en espera <6uA

Frecuencia de funcionamiento 2.4GHz

Distancia de control 30m

Temperatura de trabajo -10~40ºC

25 49

Technical specifications

90,5 15

2.4GHz Gateway

Model No.: LENNY-WIFOX1

INPUT

DC5V / 500mASET

Input Voltage: DC5V/500mA (Micro USB)

Working Temperature: -20~60°C

Communication Mode: WiFi-IEEE 802.11b/g/n 2.4GHz

RF: 2.4GHz

2.4GHz RF Transmitting Power 6dBm

2.4GHz RF Control Distance: 30m

Link

SYS

Support amazon alexa and

google assistant control

Scan to Install APP

Made in PRC

2786

• There is no need to modify the previous installation or install new wiring.

• Low cost

• 2.4RF Remote control regulation with 30 m length performances.

• Push button regulation available.

• Trailing Edge technology (ELV)

• No gap soft regulation stepping from 10% to 100%

• Fast minimum level remote control regulation.

• Overheating and overload automatic detection to turn OFF

• Supports auto transmission and synchronization so that remote control distance to be unlimited.

• Simple connection handling with input/output terminal blocks.

• Polycarbonate fire resistant housing.

TRIAC CONTROL

Smart LED control system

Installation diagram

Functioning

Short press: Switches the connected device ON/OFF.

Long press (press and hold): increases or decreases the intensity of the light.

Connection

The maximum number of TRIACs is 25 pieces and maximum wiring distance from the push button is 20m.

To control everything with a single push button, LENNY-TRIACs must be connected in cascade according to the

connection diagram.

Connection drawing

Push button controlr

Installation

Push button

Input: AC100~240V

NC NLL1

INPUT

OUTPUT

Input: AC100~240V

NC NLL1

INPUT

OUTPUT

Input: AC100~240V

NC NLL1

INPUT

OUTPUT

Push

button

Input: AC100~240V

NC NLL1

INPUT

OUTPUT

Triac dimmable LED lighting.

Traditional filament lamp.

Halogen lamp

or AC led strip (ACCX sieres)

Triac dimmable LED lighting.

Traditional filament lamp.

Halogen lamp

or AC led strip (ACCX sieres)

Triac dimmable LED lighting.

Traditional filament lamp.

Halogen lamp

or AC led strip (ACCX sieres)

Triac dimmable LED lighting.

Traditional filament lamp.

Halogen lamp

or AC led strip (ACCX sieres)

TRIAC CONTROL

Smart LED control system

Remote and panel controls

Compatible Remote and panel controls

K1: Linking, unlinking and working.

Unlinking

Linking

LENNY-PAN-B1 LENNY-PAN-B2 LENNY-PAN-K1

LENNY-MD-087LENNY-MD-006 LENNY-MD-007

1. Learning model enter.

Procedure 1:

Soft push on “SET” button from LENNY-

TRIAC1 device. Indicator led will flash very fast.

Procedure 2:

Switch off, main AC source for 10 sec,

then re-connect again.

Procedure 3: Soft push on external push button while

lighting up dimming.

Procedure 1:

LENNY-TRIAC1

Push button SET continuously for 3 sec. until indicator

led flashes quickly.

Procedure 2:

Enter learning mode

Procedure 1:

Short Push on “SET” button from LENNY-

TRIAC1. Indicator led will flash quickly.

Procedure 2:

Disconnect main AC source for 10 sec

and connect again.

Procedure 3:

Soft push on external push button while

lighting up dimming.

2. Push “SET BUTTON” on panel device LENNY-

PAN-K1 5 times during the first 3 seconds

since previous step implemented.

Indicator led light from device flashes 10

times very fast as unlinking confirmation is

reached.

2. Push “SET BUTTON” on panel device LENNY-PAN-K1

3 times during the first 3 seconds since previous

step implemented.

Indicator led light from device flashes 3 times as

linking confirmation is reached.

Indicator light

SET SET

Minimum brightness setting

This device must be paired to a remote control before this setting can be accessed.

1. Press and hold SET button for 3 seconds until indicator LED on the panel flashes once and indicator LED on

LENNY-TRIAC1 starts flashing.

2. Short press on panel to set between 10 brightness levels: 3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%.

3. Short press on panel wheel to confirm settings set or wait 10 seconds for automatic confirmation and exit

configuration mode.

TRIAC CONTROL

Smart LED control system

FUT006, FUT007, B1/T1, B2/T2, FIT087: Linking, unlinking and working.

Linking

Unlinking

1. Enter learning mode

Procedure 1: Short Push on “SET” button. Indicator

led will flash quickly.

Procedure 2: Disconnect main voltage source for

10 sec and connect again.

Procedure 3: Soft push on external push button

while lighting up dimming.

1. Enter learning mode

Procedure 1: Short Push on “SET” button. Indicator

led will flash quickly.

Procedure 2: Disconnect main voltage source

for 10 sec and connect again.

Procedure 3: Soft push on external push button

while lighting up dimming.

2. Push ON button from selected zone on

panel or remote control, during first 3

seconds since previous step implemented

Indicator led light from device flashes 3

times as linking confirmation is reached.

2. Push ON button 5 times from selected zone

on panel or remote control, during first 3

seconds since previous step implemented.

Indicator led light from device flashes 10

times as linking confirmation is reached.

led indicador

SET

Link /Unlink button

Minimum brightness setting

This device must be paired to a remote before this setting can be accessed.

1. Press and hold OFF button on the remote until LED indicator flashes once and LED indicator on the remote

starts flashing.

2. Press OFF button to set between 10 brightness levels: 3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%.

3. Press any button except OFF to confirm setting.

TRIAC CONTROL

Smart LED control system

Device auto-sync

This device can transmit the signal to another device within 30m range.

The control distance is unlimited if a device is placed every 30m.

Caution: all dimmers must be linked to a remote control device.

Important facts

1.- Main source must be switched off while installing or handling.

2.- Before anything check main AC voltage.

3.- These devices should be handled by technical staff only.

4.- Do not use devices close to metal or magnetic surfaces as they may interfere with the control signal.

Triac dimmer Triac dimmer

Auto-transmitting

TRIAC CONTROL

Smart LED control system

Mobile phone pairing (LENNY-WIFOX1)

Download and install the application on your mobile phone:

a. Via QRl code

b. Searching the Play Store for “MiBoxer”.

We will receive an e-mail with a registration verification code, which we will have to enter in the application to finish

registering account.

Once on the main screen and our session started, we must add the LENNY-WIFOX1 device. To do this:

Insert your email

adress

Insert your country Choose password Accept conditions

and terms

Push “+” to

add device

Push

“add sharing”.

Select device model:

In this case, click on “2.4GHz

Gateway WL-Box1”.

It is necessary a 5Vdc/500mA power

adaptor with micro-USB to supply

LENNY-WIFOX1.

If “SYS” indicator is not flashing, press

for 3 sec on “SET” button.

Enter network name and

password.

Attention: only 2.4GHz network is

supported (no 5G) and click on

“Start configuration”.

If you wish to link your LENNY system

with our smartphone app, LENNY-

WIFOX1 gateway is necessary.

TRIAC CONTROL

Smart LED control system

A countdown will appear and once paired, it will

indicate that pairing has been successful.

Our device will appear in the list of paired devices.

Linking your smartphone.

Once you get LENNY-WIFOX1 linking, we must get

driver linking with our smartphone app.

Click on suitable device.

First we must choose whether we are going to

configure one or more zones. In this case, as it is

a zone, we enter the “change” section and select

FUT006/FUT007.

On the screen of our mobile phone we will see image as follows:

ON / OFF

Zone

If you want to change the remote

control / remote panel, click on

“change” and select the one you

have chosen from the list.

Change temperature color if our

connected device allows it.

Brightness control

Link / Unlink

Timer

TRIAC CONTROL

Smart LED control system

Now we must link our receiver with smartphone application.

In the application we can control up to 4 zones (minimum one LENNY-TRIAC1 per zone).

To do this, we must select the zone to which we are going to link our LENNY-TRIAC1.

Once the zone has been selected, we can link / unlink the device:

In the case of unlink LENNY-TRIAC1:

• Click on “Link/Unlink”.

• Click on “unlink”.

• Remove the power supply to controller for 10 seconds.

• After 10 seconds, power the controller and in the first 3 seconds, click on the mobile screen on “unlink”.

• The light will flash three 10 times and confirm correct unlinking.

Multizone with the smartphone:

If we want to control several zones only with our smartphone we will need:

• WIFI gateway (LENNY-WIFOX1). It allows us to control up to 4 zones.

• One LENNY-TRIAC1 for each zone.

Click on “Link/Unlink”.

Click on “Link”.

Remove the power supply to controller for 10

seconds.

After 10 seconds, power the controller and in

the first 3 seconds, click on the mobile screen

on “link”.

The light will flash three times and confirm

correct linking.

TRIAC CONTROL

Smart LED control system

ALEXA linking

To control our system with Alexa, we need WIFI gateway: LENNY-WIFOX1 and link it to the smartphone (see section

“Linking with smartphone”, page 7).

Multizone with Alexa: If we want to control several zones with Alexa:

• One LENNY-WIFOX1 gateway for each zone.

• One LENNY-TRIAC1 for each zone.

Install Alexa app and log in using your account.

We need to install Mi-Light Smart skill. To do so:

Once we have reached this point, we must search for devices we want to link.

Click on “more”

and select “Skill and

games”.

In the search engine

type “Mi-Light Smart”

and click on this

option.

We allow

application using.

MiBoxer data.

If everything is

correctly done,

we will see a message

of successful linking

We have to “detect devices”. There will

be a countdown and when device is

detected, we will get a message.

Configure device we have just detected.

Select the group to which we want to link it

in Alexa.

(with intention of saying: Alexa, turn off

“bedroom” and then turn it off). So it will

tell us that it has been configured correctly.

Tabla de contenidos

Otros manuales de Sistema de control de Mi-Light

Mi-Light

Mi-Light fullwat LENNY-MD-092 Manual de usuario

Mi-Light

Mi-Light MIBOXER LDRF-RGB6-TC4 Manual de usuario

Mi-Light

Mi-Light LS3 Instrucciones de instalación

Mi-Light

Mi-Light FUT027 Instrucciones de instalación

Mi-Light

Mi-Light fullwat LENNY-PAN-B0 Manual de usuario

Mi-Light

Mi-Light MiBoxer S1-B Manual de usuario

Mi-Light

Mi-Light MIBOXER FUT043A Manual de usuario

Manuales populares de Sistema de control de otras marcas

Pentair Pool Products

Pentair Pool Products Compool Manual de usuario

ComfortNET

ComfortNET CTK04 Manual de usuario

Fireye

Fireye InSight II 95DSS3 Manual de usuario

CAME

CAME G3000 Manual de usuario

Idemia

Idemia MorphoAccess VP MD Manual de usuario

Axis

Axis P1445-LE-3 Manual de usuario

HEIDENHAIN

HEIDENHAIN TNC 150 B Manual de usuario

CNC-Step

CNC-Step High-Z T-Series Manual de usuario

Doosan

Doosan DVF Series Manual de usuario

Honeywell

Honeywell KAP 140 Manual de usuario

Honeywell

Honeywell vk41 series Manual de usuario

AirBench

AirBench FPW Guía de instalación

Cypress

Cypress HHR-3160 Manual de usuario

CAME

CAME GLT40AOS Manual de usuario

Zonex

Zonex GEN II -VVT Guía del usuario

Altronics

Altronics K 9650 Manual de usuario

micro-trak

micro-trak RoadMaster Manual de usuario

micro-trak

micro-trak Calc-An-Acre II Manual de usuario

Mi-Light fullwat TRIAC CONTROL Manual de usuario

Manuales populares de Sistema de control de otras marcas