MG M2BS2 Manual de usuario

BEFORE USE ....

Thank you for choosing us. Before use, please check con-

tents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact our sales ofﬁce or representatives.

■PACKAGE INCLUDES:

Installation base..................................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■POWER INPUT RATING & OPERATIONAL RANGE

• Refer to signal conditioner data sheet. Choose the same

power input speciﬁcation for all units.

■GENERAL PRECAUTIONS

• Before you remove the unit from the base or mount it,

turn off the power supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the installation base inside proper housing and

ventilate it.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +55°C

(23 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

• Be sure that the ventilation slits are not covered with ca-

bles, etc.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

COMPONENT IDENTIFICATION

■REAR VIEW

Specifications

MOUNTING REQUIREMENTS unit: mm (inch)

■M2BS2-04

100 (3.94)

190 (7.48)

4–M5 SCREW

■M2BS2-08

100 (3.94)

280 (11.02)

4–M5 SCREW

■M2BS2-16

100 (3.94)

460 (18.11)

4–M5 SCREW

INSTALLATION BASE MODEL M2BS2

EM-5007 Rev.1 P. 1 / 4

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

INSTRUCTION MANUAL

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

• M2BS2-041 (INPUT BASE)

1234

FG1

13 14

CH4CH1

CT PROTECTOR (CTM2)

130 (5.12)

100 (3.94)

6 (.24)

170 (6.69)

190 (7.48)

210 (8.27)

27 (1.06)

2–M3 POWER

TERMINALS

16–M3 INPUT TERMINALS

125 (4.92)*

130 (5.12)

* 165 (6.50) required for pneumatic tubing for M2PV.

** Attached to M2CA and M2CE.

• M2BS2-042 (OUTPUT BASE)

FG1

13 14

1234

CH1 CH2 CH3 CH4

6 (.24)

8–M3 OUTPUT

TERMINALS

2–M3 POWER

TERMINALS

125 (4.92)

130 (5.12) 130 (5.12)

100 (3.94)

170 (6.69)

190 (7.48)

210 (8.27)

• M2BS2-081 (INPUT BASE)

12345678

5588

14 14

CH7CH1

FG1

13 14

CH8

CT PROTECTOR (CTM2)

130 (5.12)

100 (3.94)

6 (.24)

260 (10.24)

280 (11.02)

300 (11.81)

27 (1.06)

2–M3 POWER

TERMINALS

32–M3 INPUT TERMINALS

125 (4.92)*

130 (5.12)

* 165 (6.50) required for pneumatic tubing for M2PV.

** Attached to M2CA and M2CE.

• M2BS2-082 (OUTPUT BASE)

FG1

13 14

12345678

CH3 CH4 CH5 CH6 CH7 CH8

CH1 CH2

6 (.24)

16–M3 OUTPUT

TERMINALS

130 (5.12)

100 (3.94)

260 (10.24)

280 (11.02)

300 (11.81)

2–M3 POWER

TERMINALS

125 (4.92)

130 (5.12)

M2BS2

EM-5007 Rev.1 P. 2 / 4

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

• M2BS2-161 (INPUT BASE)

CH5CH1

FG1

13 14

12345

5858585858

6789

1414141414

11 12 13 14 15 16

CH10CH6 CH16CH11

130 (5.12)

100 (3.94)

6 (.24)

440 (17.32)

460 (18.11)

480 (18.90)

27 (1.06)

2–M3 POWER

TERMINALS

64–M3 INPUT TERMINALS

125 (4.92)*

130 (5.12)

* 165 (6.50) required for pneumatic tubing for M2PV.

** Attached to M2CA and M2CE.

CT PROTECTOR (CTM2)

• M2BS2-162 (OUTPUT BASE)

FG1

13 14

123456789

10 11 12 13 14 15 16

CH11 CH12 CH13 CH14 CH15 CH16

CH6 CH7 CH8 CH9 CH10

CH1 CH2 CH3 CH4 CH5

6 (.24)

32–M3 OUTPUT TERMINALS

130 (5.12)

100 (3.94)

440 (17.32)

460 (18.11)

480 (18.90)

2–M3 POWER

TERMINALS

125 (4.92)

130 (5.12)

M2BS2

EM-5007 Rev.1 P. 3 / 4

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

■CONNECTION DIAGRAM

Ch.16*

INPUT

Ch.1

INPUT

U(+)

V(–)

POWER

FG1

■INPUT BASE

Ch.16*

OUTPUT

Ch.1

OUTPUT

■OUTPUT BASE

*Up to Ch.4 for M2BS2-04, Ch.8 for M2BS2-08.

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable.

Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)

Recommended manufacturer: Japan Solderless Terminal

MFG.Co.Ltd, Nichifu Co.,ltd

6 (.24) max

3.3 (.13) max

mm (inch)

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagrams of the in-

stallation base and the mounted signal conditioners.

2) Power input voltage

3) Installation & environments

LIGHTNING SURGE PROTECTION

We offer a series of lightning surge protector for protec-

tion against induced lightning surges. Please contact us to

choose appropriate models.

M2BS2

EM-5007 Rev.1 P. 4 / 4

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Este manual sirve para los siguientes modelos

Otros manuales de Sistema de E/S de MG

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario