MFTech USB-Interface Manual de usuario
Quickstart USB-Interface
1. Transmitter settings
Connect your R/C transmitter (in PPM mode, without RF part /
unplugged crystal) with the Interface only if it is switched off!
The R/C Interface is connected with the buddy box. Thus, the
transmitter acts like a slave transmitter. You should set up your
transmitter for slave mode and make any settings necessary for
slave operation. For further information see the instruction
manual of your transmitter(how to switch off the RF part, unplug
the crystal oscillator, special settings, ..).
Detach all servos, motor controllers, devices and the battery
from the R/C receiver and only connect the receiver cord. The
USB-Interface supplies the receiver with power, no battery may
be connected additionally. First connect the receiver with the
USB-Interface, then connect the Interface with your PC.
Use Stick Mode “Stick Mode 1”in IntCon for the operation with
an receiver. The default setting is “RF G2”.
For USB-Interface III:
2. Driver installation
Windows 2000 / XP / Vista:
Windows 98 SE / ME:
Connect the Interface with your PC wait a short-time LED glows
Switch on your R/C transmitter LED flashes finished
Connect the USB-Interface with your PC Windows starts the
hardware assistant select “choose manually”select “HID-
compliant device”
Insert the Windows CD to copy the drivers LED glows switch on
your R/C transmitter LED flashes finished
If the hardware assistant does not start automatically: Start the
assistant In Control Panel | Hardware manually “choose manually”
→ →
→ → →
→
→ →
→ →
→ →
→
short time after connection..
..2 new items in device manager
then choose HID see Win XP→
3. Test
Test in
Control Panel | Game Controller:
do calibrate, test only!
not
4. Simulator
Connect the Interface with your PC before you attach the
R/C transmitter!
FMS
Easyfly
Aerofly Pro
Realflight G2
: Controls Analog Control Joystick Interface
Mapping / Calibration calibrate
: Select joystick calibrate
: Calibrate Joystick Properties
calibrate, Controls Joystick Properties assign
channels
: Settings Calibrate device Device:
select Joystick (manually) calibrate, assign channels
in Advanced Settings
Other Simulators:
The USB-Interface can control all simulators (Aerofly,
Piccofly, MS Flight Simulator, ..), car simulators and
games, that can be controlled by a normal joystick, too.
→ → →
→
→
→ → →
→ → →
→ →
→
USB-Interface
Quickstart USB-Interface
5. Install IntCon
Installation
1. Download IntCon from .
2. Extract / install the content of the archive to C:\Program
Files\IntCon\.
1. Connect the USB-
Interface with your PC.
2. Double-click on
intcon.exe to open IntCon.
3. Mark the USB-Interface
in the table
(Name RC USB,
Vendor MFTech).
4. Click “Open”.
5. Configure the USB-Interface.
Start
http://www.mftech.de/software.htm
6. Configure the Interface
7. irmwareUpdate f
1. Plug the Interface into the PC.
2. Start IntCon USB-Interface is listed.
3. Double click the Interface, check "Activate Bootloader".
4. Click “Apply”and close the window.
5. If you unplug the Interface and reconnect it again, a new joystick
named “Loader”is detected. Windows will install new drivers for it. After
a delay of 10 seconds the boot loader disappears and the normal
“RC USB”joystick is back again. The boot loader will always start
directly before the normal joystick after connecting. If you want to switch off the boot loader
(e.g. after a successful firmware update) then uncheck “Activate Bootloader”.
6. Now you can update the firmware with the “Firmware...”button. Connect the Interface, do
“Erase”, then “Program”(and optionally “Verify), then “Reset”.“LED”causes the Interface to
toggle the LED. This is just for communication test purpose.
Software for the Interface is located at
→
http://forum.mftech.de
8. Further informationen
Website:
this quickstart:
detailed instruction manual:
MFTech .Ralf Kretschmann .Kaiserstraße 25a .67722 Winnweiler
info@MFTech.de .www.MFTech.de
http://www.mftech.de
http://www.mftech.de/quickstart_en.pdf
http://www.mftech.de/usb-interface.pdf
5.3.2007
Set up joystick buttons automatically:
- 1. button controlled by 5th R/C channel
- 1. button controlled by 3rd R/C channel
- all buttons off
Set up joystick axis
automatically:
- Throttle/ aileron right
- Throttle left, ailerons right
- Throttle right, ailerons left
- Throttle/ ailerons left
Set up joytick buttons
manually:
Button is triggered by
selected R/C channel
Button is triggered if R/C
channel exceeds this limit
Set up axis manually:
Axis is controlled by the
selected R/C channel
Invert direction of motion
of the axis
Set up mixers
Set up buttons manually:
I
Button can be triggered or
is always off
nvert the state of the button
Write configuration
to the RC-Interface
Read configuration
from the RC-Interface
store configuration
in the RC-Interface
Close window
Save settings
in file
Read settings
(for transmitter/
simulators)
from file
Manuales populares de Interfaz USB de otras marcas
PASCO
PASCO SCIENCEWORKSHOP 750 Manual de usuario
Phonic
Phonic FIREFLY 302 USB Manual de usuario
OHAUS
OHAUS Scout STX Series Manual de usuario
Denon
Denon DN-HC4500 - DJ Mixer USB Controller Manual de usuario
Lutron Electronics
Lutron Electronics Stanza SZ-CI-USB-CPN5138 Manual de usuario
Paradox
Paradox PMC5-TI00 Manual de usuario
Thorsis Technologies
Thorsis Technologies isDNet USB Manual de usuario
Thorsis Technologies
Thorsis Technologies isHRT USB Manual de usuario
microHAM
microHAM DigiKeyer Manual de usuario
Apogee
Apogee Jam X Manual de usuario
RigExpert
RigExpert TI-3000 Manual de usuario
microHAM
microHAM USB Interface II Manual de usuario