MFJ MFJ-1795 Manual de usuario

MFJ-1795 Vertical Antenna Instructions

MFJ-1795 Vertical Antenna

INTRODUCTION

The MFJ-1795 HF antenna was designed to provide portable or permanent operation from

restricted locations. When combined with the MFJ Ground-Coupled™ Portable Antenna Base or

other suitable grounding system, such as radial system, the result is a small vertical antenna

under 10 feet in height.

The reduction in size is accomplished by adding separate loading coils and capacitance hats for

each band at the top of the antenna. The efficient end loading coils are wound on fiberglass

forms. The high quality materials and construction of the HF loading system allows a maximum

power rating of 1500 watts SSB PEP on 40, 20, 15 and 10 meters.

The power rating of this antenna varies from band to band. The PEP ratings are primarily

determined by the voltage breakdown of the components, while the CW ratings are generally

determined by the components heating.

The following chart lists the power rating and the 2:1 VSWR bandwidth of this antenna:

Band Power Bandwidth

CW SSB RTTY

40m 700 1500 500 100KHz

20m 1250 1500 750 400KHz

15m 1250 1500 1000 1800KHz

10m 1250 1500 750 1200KHz

The weight and wind load of this antenna are 10 pounds and approximately two square feet

respectively.

WARNING: Improper installation and assembly can be hazardous! Read

these instructions thoroughly before attempting to assemble, install, or

operate this product! High power transmitting devices produce voltages that

can cause severe burns or other injuries.

CHOOSING A LOCATION FOR THE ANTENNA

The best performance on receiving and transmitting will be obtained by mounting the antenna in

a clear location above or away from buildings, towers, feed-lines, utility wires, and other

antennas. While your own ingenuity and particular circumstances will determine the final

mounting method, we will pass along a few ideas for both permanent and portable installation.

MFJ-1795 Vertical Antenna Instructions

WARNING: Always mount this antenna so that it is out of the reach of adults as well as

children. The capacitance elements can cause injury and or severe RF burns.

•

Never place this antenna in a location that will permit people to encounter the loading

spokes or any other part of the antenna.

•

Never place this antenna where a mechanical failure might allow the antenna to contact

power lines or other utility wires.

•

Always ground the feed-line at the point where it enters a building to a good earth ground

for lightning protection.

•

Follow the guidelines for antenna installations as recommended by the US consumer

product safety commission.

ANTENNA HEIGHT

The height of the radiating element is adjustable from 5 to 8 feet. Maximum radiation will be

obtained by setting the height of the radiating element at 8 feet. Some installations may require

the antenna height to be reduced. An example may be the installation of the antenna inside a

backyard fence for concealment. Height adjustment will be discussed in the assembly section of

this manual.

INSTALLATION

The MFJ-1795 was designed as a low profile, portable antenna. When combined with the MFJ

Ground-Coupled™ Portable Antenna Base the antenna will provide permanent or portable

communications. This is an ideal antenna for restricted locations. However, the antenna

installation MUST be protected with non-metallic fencing to provide personal safety and to

prevent antenna damage. The antenna can be installed using the supplied mounting bracket and

a suitable ground radial system.

IMPORTANT:A suitable ground plane must be installed with this antenna.

PORTABLE SETUP

The antenna may be disassembled to the extent necessary for transporting to a temporary

location. Before the antenna is disassembled, some type of marks should be placed on the mast

of the antenna to ensure it will be the same height as before. Some retuning may be required

after moving the antenna.

MFJ-1795 Vertical Antenna Instructions

WARNING: If the antenna falls it will be damaged and may cause serious injury.

Whatever type of installation you choose, remember that the antenna should be installed

where it can never be contacted by people or animals.

TOOLS AND TIME REQUIRED FOR ASSEMBLY

The estimated assembly time for this antenna is 1 hour. Antenna assembly requires the following

hand tools:

[ ] soldering iron and solder

[ ] 5/16" nut driver (or 1/4" flathead screwdriver)

[ ] 7/16" open end wrench

[ ] large wire cutters

[ ] small pliers

[ ] #1 phillips screwdriver

[ ] #2 phillips screwdriver

[ ] suitable eye protection

In addition, you will need two stable supports at least 30" tall (i.e. saw horses or trash cans) and a

short (6 to 8 feet) temporary mast (1 to 1-1/2 inches outside diameter) for temporary mounting

during tuning.

MFJ-1795 PARTS LIST

As you unpack your antenna you should find the parts in the following list.

[ ] 3 bundles of wire capacitance spokes 12 short, 4 medium, (and 4 spare long spokes)

[ ] 5' radiator 1 1/8"

[ ] 30”x 1” radiator

[ ] 9”x 1 1/8” radiator

[ ] loading coil assembly

[ ] base mounting bracket

[ ] hollow fiberglass rod insulator

[ ] One Hardware Bag containing

[ ] 4 1.5” hose clamps

[ ] bag of short 6-32 stainless screws

[ ] 4 U-bolts with hardware

[ ] two plastic tie wraps

[ ] 2 solder lugs

For installation you will need some additional items not supplied with the antenna installation

kit.

MFJ-1795 Vertical Antenna Instructions

[ ] Quality low-loss 50-Ohm coax with a PL-259 to go from the antenna to the transmitter.

[ ] Either a SWR meter or Analyzer (MFJ-259, 269)

SAFETY PRECAUTIONS:

WARNING: You can be killed if the antenna, feedline, or the equipment used to install

the antenna accidentally contacts any utility lines. Never install an antenna near power

lines!

1. Be careful while carrying the antenna. It is heavy enough to cause you to lose your balance if

it is handled too casually or if the capacitance spokes become entangled in obstructions.

2. Mount the antenna in a way so that it is out of reach. The ends of the capacitance spokes can

cause eye injury, serious RF burns or both.

3. Make sure that a mast, if used, is sturdy enough to support the weight and the wind load.

ASSEMBLY AND INSTALLATION PROCEDURE

During assembly of this antenna refer to the figures in this manual and the picture on Page 1.

NOTE: Wear safety glasses whenever working on or near this antenna.

Do not tighten the screws that connect the loading coil terminal lugs to the capacitance hats or

you will BREAK the fiberglass form. If the terminal lugs loosen tighten the NUT on the lug.

STEP-BY-STEP PROCEDURE

[ ] 1. Prepare a temporary work surface, such as a table, two saw horses, or trash cans, to be

used while installing the parts onto the antenna.

[ ] 2. Sort out the parts you have unpacked into groups of similar parts. Be sure all the parts are

available.

[ ] 3. After examining the antenna parts, gather the tools needed for basic assembly. At the

minimum these consist of:

[ ] #1 Long Phillips screwdriver for capacitance spoke screws

[ ] 1/4" flathead screwdriver or a 5/16" nut driver for hose clamps.

MFJ-1795 Vertical Antenna Instructions

[ ] Two 7/16" open end wrenches or one wrench and one nut driver for the U-bolts.

[ ] Heavy Wire cutters for trimming capacitance spokes.

[ ] Safety glasses.

[ ] 4. Decide on the approximate height of the antenna. Maximum height will be just under 10

feet while minimum will be 6 1/2 feet.

[ ] 5. The 6 1/2 foot level can be reached by using the 5’ radiator. If this is the desired height

steps 6-8 may be skipped. Heights above this level will be reached using the additional

pieces of tubing.

[ ] 6.Now take the 1.0” x 30” piece of aluminum and place at a minimum 2 inches into the

long aluminum element (5’ x 1 1/8”). The end of the long (5’) piece used should be the

one without the hole drilled in it. See Figure 1.

[ ] 7. A hose clamp should be placed around the 1 1/8” pipe to secure it in place. Tighten it with

the 5/16” nut driver.

[ ] 8.A minimum of 2 inches of the 9” x 1 1/8” pipe should be placed onto the 1.0” x 30” piece

of aluminum and secured with a hose clamp.

Figure 1

NOTE: The length of tubing placed inside 1 1/8” tubing will determine the overall height of

the antenna.

[ ] 9. Now the hollow fiberglass insulator should be placed approximately 3 1/2” into the 60” x

1 1/8” aluminum tubing. See Figure 2.

Fiberglass Insulator

Solder Lug

60 x 1 1/8 Mast Pipe

Antenna Feed Point

Hose Clamp

Figure 2

MFJ-1795 Vertical Antenna Instructions

[ ] 10. Place one of the hose clamps around the aluminum tubing and snug the clamp using a

5/16” nut driver . The center conductor of the coax will be connected to the antenna using

a solder lug placed under the clamp. Refer to figure 2.

[ ] 11. Install the short 6/32” screws in the rings of the loading coil assemblies and place a 6/32”

nut on each screw. Put the four medium capacitance spokes in the four holes on the rings

of the coil assembly. Then, tighten the screws until the spokes are snug. Now you should

be able to turn the coil assembly over and they should balance on the long spokes. See

Figure 3.

6-32” screw

Loading Coil Assembly

Figure 3

IMPORTANT: Do not use a high torque electric screwdriver to mount the capacitance

spokes. The screw heads will be sheared off if too much torque is applied.

[ ] 12. Install four short capacitance spokes in the next 3 sets of rings. Again, tighten these spokes

as was done in step 9. (See Figure 3)

[ ] 13. Slide a hose clamp over the top radiator. Mount the top coil assembly to the antenna by

inserting the fiberglass insulator in the top radiator. Tighten the metal strap from the coil

assembly under the hose clamp. See Figure 4.

MFJ-1795 Vertical Antenna Instructions

Loading Assembly

40 m 20 m 15 m 10 m

Hose Clamp

Figure 4

[ ] 14. Double check the tightness of all the hardware you installed. Then, mount the antenna on

the short temporary tuning mast or the MFJ Ground Coupled Portable Antenna Base.

[ ] 15. Secure the mounting bracket to the fiberglass insulator as shown in Figure 5. Make sure

the antenna mast does not contact the U-bolts. The next four steps may be skipped if the

antenna uses the MFJ-1904 Antenna Base.

MFJ-1795 Vertical Antenna Instructions

Figure 5

[ ] 16. Ground radials should be attached to the U-bolts on the Base Mounting Bracket.

[ ] 17. The antenna should be fed using a good quality 50-Ohm low-loss coax such as RG-8 or

RG-58. Approximately 4 inches of the outer insulation should be removed. The center

conductor of the coax should be soldered to the solder lug that was placed on the _” bolt in

step 10 of the assembly. The outer shield of the coax should be soldered to the additional

solder lug supplied in the parts bag. Place this solder lug onto one of the U-bolts located

on the mounting bracket Secure it using one of the _ “nuts supplied with the U-bolts.

WARNING: Serious burns can be received with improper use of a soldering iron.

[ ] 18. Tune the antenna by following the instructions under the section “Frequency and SWR

Adjustment”.

[ ] 19. Mount the antenna in its permanent location. Slight retuning and height adjustment may

be necessary.

USING THE MFJ GROUND-COUPLED™ PORTABLE ANTENNA BASE WITH THE

MFJ-1795

The antenna base should be assembled using the instructions supplied with the unit. The

following instructions will explain the installation of the MFJ-1795 to the antenna base.

[ ] 1. The U-bolts should be attached to the base through the holes as indicated in Figure 5.

[ ] 2. The So-239 connecter, supplied with the base, should then be installed on the top of the

base plate mount as indicated in Figure 6 using two 6/32” x 3/8” screws and kep nuts

supplied with the base. One of the feed-points at the bottom of the base may also be used.

The insulated wire supplied with the MFJ-1904 will be long enough for this application.

This will increase the radiating length of the antenna.

MFJ-1795 Vertical Antenna Instructions

Figure 6

U-bolts

Bushing

SO-239

Anetnna Base

[ ] 3. The plastic bushing supplied in the parts should be placed in the hole under the SO-239

connector.

[ ] 4. Now the 15” piece of insulated wire should be passed through the plastic bushing to the

antenna feed-point.

SO-239

Bus Wire

Figure 7

MFJ-1795 Vertical Antenna Instructions

WARNING: Serious burns can be received with improper use of a soldering iron.

[ ] 5. The wire should now be soldered to the center pin of the SO-239 connecter.

[ ] 6. Remove the fiberglass tubing from the aluminum tubing of the assembled antenna by

loosening the hose clamp. Place the solder lug, under the hose clamp and retighten.

[ ] 7. Insert the fiberglass tubing through the U-bolts and tighten the nuts. This will make base

installation much easier.

[ ] 8. Adjust the wire length so that it approaches the soldering lug at the antenna feed-point.

[ ] 9. Carefully solder the insulated wire to the solder lug.

[ ] 10. Tighten the nuts on the U-bolts firmly.

[ ] 11. Re-attach the antenna to the fiberglass tubing by tightening the hose clamp. Remember to

place the solder lug attached to the center conductor of the coax under the hose clamp

[ ] 12.Make sure that the aluminum tubing, the insulated wire, and solder lugs DO NOT COME

INTO CONTACT WITH THE ANTENNA BASE. Small readjustments of the

fiberglass insulator may necessary.

REMOVING THE ANTENNA FROM THE BASE OR BRACKET

The antenna may be quickly removed to be hidden from view. This is easily accomplished by

loosening the hose clamp at the base of the antenna shown in Figure 2. Carefully pick up the

antenna mast. Be sure to watch for overhead tree limbs and other objects that could come in

contact with the antenna during removal. These objects could cause the antenna to become

unbalanced and fall, resulting in personal injury and damage to the antenna. Store the antenna in

a safe place to prevent damage.

FREQUENCY AND SWR ADJUSTMENT

This antenna covers wider frequency ranges on the higher bands, and narrower segments on the

lower frequency bands. The 40 meter band has the narrowest range of operation (approximately

40 KHz) and is the most sensitive to adjustments.

The entire antenna must be accessible during initial tuning and testing. If the MFJ Ground

Coupled™ Portable Antenna Base is used, attach the antenna to the base and place it in a

location away from buildings or other objects that could affect the measurements. If the portable

antenna base is not used, it is best to install the antenna on a short, temporary mast or pipe.

Tabla de contenidos

Otros manuales de Antena de MFJ

MFJ

MFJ MFJ-1799 Manual de usuario

MFJ

MFJ 1801 Manual de usuario

MFJ

MFJ MFJ-1866 Manual de usuario

MFJ

MFJ MFJ-1982LP Manual de usuario

MFJ

MFJ MFJ-1756 Manual de usuario

MFJ

MFJ Super Hi-Q Loop MFJ-1786 Manual de usuario

MFJ

MFJ MFJ-918BP Manual de usuario

MFJ

MFJ Box Fan -1780 Manual de usuario

MFJ

MFJ MFJ-1886 Manual de usuario

MFJ

MFJ MFJ-1786 Manual de usuario

MFJ

MFJ 1779C Manual de usuario

MFJ

MFJ MFJ-1795W Manual de usuario

MFJ

MFJ MFJ-1422 Manual de usuario

MFJ

MFJ MFJ-1024 Manual de usuario

MFJ

MFJ MFJ-2289 Big Ear Manual de usuario

MFJ

MFJ MFJ-1754 Manual de usuario

MFJ

MFJ MFJ-1838 Manual de usuario

MFJ

MFJ 1790 Manual de usuario

MFJ

MFJ MFJ-1762 Manual de usuario

MFJ

MFJ IntelliTuner -991 Manual de usuario

MFJ

MFJ MFJ-918WM Manual de usuario

MFJ

MFJ MFJ-1742 Manual de usuario

MFJ

MFJ Super Hi-Q Loop Manual de usuario

MFJ

MFJ Mobile Big Stick MFJ-1652 Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario