MFJ MFJ-1736 Manual de usuario

MFJ-1736 Six-Meter Roll-up J-Pole Antenna Instruction Manual

1

MFJ-1736 Six-Meter Roll-up J-Pole Antenna

INTRODUCTION

The MFJ-1736 was designed for fixed or portable six-meter FM operation. Despite its

light weight and simplicity, the J-pole is a time-proven design that radiates efficiently and

exhibits low VSWR. When correctly installed, your antenna's resonant frequency should

fall around 52.5 MHz and exhibit a VSWR of less than 2:1 over most FM segments of the

band.

THEORY OF OPERATION

The MFJ-1736 consists of a 1/2-wave radiator which is voltage-fed by a matching stub.

Coax is tapped onto the stub at the correct low-impedance feedpoint to provide a 50-ohm

match. Both sides of the radiating portion are tied together to increase apparent element

diameter and improve operating bandwidth.

A special water-proof sealant has been applied to the coax braid and to all solder

connections to prevent water migration into the cable. Heat shrink has been applied to

provide more durability to the connections. The MFJ-1736 comes ready to use.

However, be sure to seal all coaxial connectors against weather and moisture in normal

fashion.

INSTALLATION

The coax cable makes it possible to connect directly to an SO-239 connector or an

extension of any length needed. The antenna may be supported over any convenient tree

limb or non-metallic structure with inexpensive nylon string. Avoid installing the MFJ-

1736 near wires, other feedlines, or large metallic surfaces that could distort the radiation

pattern or detune the element.

WARNING:Never install near power lines.

MFJ-1736 Six-Meter Roll-up J-Pole Antenna Instruction Manual

2

Since the J-pole must also support its feedline, use light-weight cable. RG-58 is

satisfactory for runs less than 30 feet. RG-8M is recommended for longer runs. This

cable has low loss at 50-MHz, is relatively inexpensive and light-weight. As with most

VHF antennas, the higher you raise the J-pole, the better it will perform.

The bottom 2 to 3 inches of the stub (below the feedpoint) should be bent away from the

coax to prevent detuning by the coax shield.

TECHNICAL ASSISTANCE

If you have any problem with this unit first check the appropriate section of this manual.

If the manual does not reference your problem or your problem is not solved by reading

the manual, you may call MFJ Technical Service at 662-323-0549 or the MFJ Factory at

662-323-5869. You will be best helped if you have your unit, manual and all information

on your station handy so you can answer any questions the technicians may ask.

You can also send questions by mail to MFJ Enterprises, Inc., 300 Industrial Park Road,

Starkville, MS 39759; by Facsimile (FAX) to 662-323-6551; or by email to

[email protected]. Send a complete description of your problem, an

explanation of exactly how you are using your unit, and a complete description of your

station.

Tabla de contenidos

Otros manuales de Antena de MFJ

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario